Integrated Circuits Inc. aIVR8511 APLUS MAKE YOUR PRODUCTION A-PLUS Data Sheet aIVR8511 – 85 sec APLUS INTEGRATED CIRCUITS INC. Address: 3 F-10, No. 32, Sec. 1, Chenggung Rd., Taipei, Taiwan 115, R.O.C. (115)台北市南港區成功路一段 32 號 3 樓之 10. Sales E-mail: [email protected] TEL: 886-2-2782-9266 FAX: 886-2-2782-9255 WEBSITE : http: //www.aplusinc.com.tw 2 Support E-mail: [email protected] Aug 23, 2010 Integrated Circuits Inc. aIVR8511 FEATURES Standard CMOS process. Embedded EPROM. Embedded 8-bit MCU. 85sec voice duration at 6 KHz sampling with 4-bit ADPCM compression. Combination of voice building blocks to extend playback duration. Table entries are available for voice block combinations. User selectable PCM or ADPCM data compress. Voice Group Trigger Options: Edge / Level; Hold / Un-hold; Retrigger / Non-retrigger. Programmable I/Os, Timer Interrupt and Watch Dog Timer. Built-in oscillator with fixed Rosc, software control sampling frequency 2.2V – 3.6V single power supply and < 5uA low stand-by current. PWM Vout1 and Vout2 drive speaker directly with two levels of volume selection. D/A COUT with ramp-up ramp-down option to drive speaker through an external BJT. DESCRIPTION Aplus’ aIVR8511 is a 8-bit MCU based Voice chip. It is fabricated with Standard CMOS process with embedded voice storage memory. It can store 85sec voice message with 4-bit ADPCM compression at 6KHz sampling rate. 8-bit PCM is also available as user selectable option to improve sound quality. There are eleven programmable I/O pins. Key trigger and Parallel CPU trigger mode can be configured according to different application requirement. User selectable triggering and output signal options provide maximum flexibility to various applications. Built-in resistor controlled oscillator, 8-bit current mode D/A output and PWM direct speaker driving output minimize the number of external components. Two levels volume control for PWM speaker direct drive is available. 3 Aug 23, 2010 Integrated Circuits Inc. aIVR8511 PIN CONFIGURATION PIN DESCRIPTIONS Pin Names VOUT1 VOUT2_COUT Description PWM output to drive speaker directly PWM output or COUT DAC output select by programmable option VSS Power Ground OSC Oscillator input VDDA Positive Power Supply VDD Positive Power Supply PB0~PB3 Programmable I/O port B PC0~PC3 Programmable I/O port C PD0~PD2 Programmable I/O port D RSTB Reset pin, Low active Note: PB, PC and PD ports are software programmable I/O pins that can be set to different configurations such as pure input, input with pull-up, input with pull-down and output. The programmable I/O pins set up will take effect immediately after chip RESET is applied. Pins for memory programming are: VDD, VDDA, VSS, PB0, PB1, OSC, VOUT2 and RSTB. 4 Aug 23, 2010 Integrated Circuits Inc. aIVR8511 BLOCK DIAGRAM OSC VDD Oscillator MEMORY GND Clock Tree Generator PB0 ~ 3 PC0 ~ 3 PD0 ~ 2 VDDA 8-bit MCU I/O PWM Driver & 8-bit DAC VOUT1 VOUT2_ COUT ABSOLUTE MAXIMUM RATINGS Symbol Rating Unit VDD - VSS -0.5 ~ +4.0 V VIN VSS - 0.3<VIN<VDD + 0.3 V VOUT VSS <VOUT<VDD V T (Operating): -40 ~ +85 ℃ T (Junction) -40 ~ +125 ℃ T (Storage) -55 ~ +125 ℃ 5 Aug 23, 2010 Integrated Circuits Inc. aIVR8511 DC CHARACTERISTICS ( TA = 0 to 70℃, VDD = 3.0V, VSS = 0V ) Symbol Parameter Min. Typ. Max. Unit VDD Operating Voltage 2.2 3.0 3.6 V ISB Standby current 1 5 µA I/O properly terminated IOP Operating current 7 mA I/O properly terminated VIH "H" Input Voltage 2.5 3.0 3.5 V VDD=3.0V VIL "L" Input Voltage -0.3 0 0.5 V VDD=3.0V IVOUTL_N VOUT low O/P Current (Normal Volume) 130 mA Vout=1.0V IVOUTL_H VOUT low O/P Current (High Volume) 200 mA Vout=1.0V IVOUTH_N VOUT high O/P Current (Normal Volume) -130 mA Vout=2.0V IVOUTH_H VOUT high O/P Current (High Volume) -200 mA Vout=2.0V ICO COUT O/P Current -2 mA Data = 80h IOH O/P High Current -10 mA VOH=2.5V IOL O/P Low Current 17 mA VOL=0.3V RNVOUT VOUT pull-down resistance 100K Ω VOUT pin set to internal pull-down RNPIO Programmable IO pin pull-down resistance 1M Ω PBx, PCx, PDx set to internal pull-down RUPIO Programmable IO pin pull-up resistance 3.3K 4.7K Ω PBx, PCx, PDx set to internal pull-up ∆Fs/Fs Frequency stability -3 +3 % ∆Fc/Fc Chip to chip Frequency Variation -5 6 +5 % Conditions VDD = 3V +/- 0.4V Also apply to lot to lot variation Aug 23, 2010 Integrated Circuits Inc. aIVR8511 TYPICAL APPLICATIONS R1 1M C1, 0.1uF VDD,VDDA ROSC=610K OSC VOUT1 PB0 PB1 PB2 3.3V C2 SP VOUT2_ COUT PB3 Rrst = 4.7K RSTB VSS Crst = 0.1uF Note: 1. PB0 to PB2 are set to input; PB3 is set to output 2. C1 must be connected directly on the VDD and VSS pins of the chip 3. R1 is optional for fast discharge of C1 and Crst when power off. 4. C2 is added according to the table below: VOUT Volume SPK C2 Normal 8, 16 or 32 Ω Not needed High 16 or 32 Ω Not needed High 8Ω 1000pF (102) High <8Ω 2000pF (202) Using 3.3V Battery Direct Drive Speaker HT7335 C1, 0.1uF ROSC = 610K 8Ω 1/4W Speaker VDD,VDDA OSC 4.5V VOUT2_ COUT PB0 PB1 PB2 Tr Rb 4.7K RSTB VSS 0.1uF Note : PB0 to PB2 are set to input C1 must be connected directly on the VDD and VSS pins Output driving of HT LDO: HT7133 (30mA, 3.3V) HT7536 (100mA, 3.6V) HT7335 (250mA, 3.5V) Using 4.5V Battery with COUT speaker drive 7 Aug 23, 2010 Integrated Circuits Inc. aIVR8511 VIN=+5V VOUT=+3.5V HT7335 C1, 0.1uF ROSC =610K 4.7K 8Ω 1/4W Speaker VDD,VDDA OSC MCU Addr[0] Addr[1] Addr[2] PB0 PB1 PB2 PB3 IO0 VOUT2_ COUT Tr Rb RSTB 0.1uF VSS Note : PB0 to PB2 set to internal pull-up Addr[0] to [2] are open drain output drive 5V CPU Control with COUT Note for COUT speaker drive: 1. C1 must be connected as close to the chips VDD and VSS pins as possible. 2. Rb is base resistor from 120 Ohm to 390 Ohm depends on value of VDD and transistor gain. 3. Tr is an NPN transistor with beta larger than 150, e.g. 8050D. 4. Rosc = 610K Ohm with Vdd=3.0V can support sampling rate up to 14KHz. 5. For sampling rate higher than 14KHz, smaller value of Rosc should be used. Bonding Diagrams Note: Substrate must be connected to VSS 8 Aug 23, 2010