Multi-Deck Rotary Switches SERIES 08 SERIES 09

Multi-Deck Rotary Switches
SERIES 08
SERIES 09
0.5" Diameter, 1/4 Amp,
Standard, Military SR13
FEATURES
• Proven Quality in Thousands of
Applications
• Gold-plated Contact System
• 30°, 36°, 45°, 60° and 90° Angle
of Throw Options
• MIL Qualified Versions MIL-S-3786/13
DIMENSIONS
In inches (and millimeters)
Standard Style
Rear Views
Series 09
30° Angle of Throw
Front view shows terminal location
of Series 8, 36° angle of throw.
Transpose rear view for terminal
location of other angles of throw.
DIM. A + .046 – .020
(+ 0,05 – 0,51)
.135 ± .015 (3,43 ± 0,38)
0 9
1
11
1 12
#0 THREAD
.250 ± .020
(6,35 ± 0,51)
15°
2
SEE NOTE
.387 (9,83) SER.8
.453 (11,51) SER. 9
± .015 (0,38)
30°
.125 + .001 – .002
(3,18 + 0,03 – 0,05)
DIA.
COMMON LUG
COMMON LUG
.045 ± .003 (1,14 ± 0,08) DIA.
HOLE AFTER PLATING
NON-TURN TAB .062 ± .005
(1,58 ± 0,13) WIDE BY
.020 ± .003 (0,51 ± 0,08) THICK
Series 08
36° Angle of Throw
INTEGRAL ASSEMBLY NUT,
DO NOT REMOVE
1/4-32 UNEF-2A THREAD
.687 ± .015
(17,45 ± 0,38)
OVER
TERMINALS
Note: Common location for a single pole per
deck switch. For common location on
multi-pole switches, see circuit diagrams.
.500 ± .020
(12,7 ± 0,51)
DIA.
Dimension
B
.960
1.228
1.496
1.764
2.032
2.550
.062
.062
.062
.062
.062
.312
(24,38)
(31,19)
(38,00)
(44,81)
(51,61)
(64,77)
(1,57)
(1,57)
(1,57)
(1,57)
(1,57)
(7,92)
12
14
16
18
20
22
16.0
18.5
21.0
23.5
26.0
28.5
7
8
9
10
11
12
Dimension
A
2.818
3.086
3.354
3.622
3.890
4.158
(71,58)
(78,38)
(85,19)
(91,00)
(98,81)
(105,61)
Dimension
B
.312
.312
.312
.312
.312
.312
(7,92)
(7,92)
(7,92)
(7,92)
(7,92)
(7,92)
Grayhill part number and date code marked on standard style detent cover label.
Customer part number marked on request. Grayhill part number and date code
printed on military style cover. Military number printed when required.
Rotary
16
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
24
26
28
30
32
34
31.0
33.5
36.0
38.5
41.0
43.5
36°
COMMON
LUG
GRAYHILL
Approx. Weight
Grams
Srs. 08 Srs. 09
1
Approx. Weight No.
Grams
of
Srs. 08 Srs. 09 Decks
4
1
2
3
4
5
6
Dimension
A
5
No.
of
Decks
7
6
10 9
8
2
Rotary Switches
.562 (14,27) SER. 8
.625 (15,88) SER. 9
8
7 6 5
.094 ± .010
(2,38 ± 0,25)
GRAYHILL
.375 ± .020
(9,53 ± 0,51)
3
CL OF NON-TURN
TAB
.750 ± .015
(19,05 ± 0,38)
OVER TERMINALS
DIM. B REF.
STUD
PROJECTION
3
.312 ± .020
(7,92 ± 0,51)
4
.260 ± .015
(6,60 ± 0,38)
.562 ± .020
(14,27 ± 0,51)
DIA.
.033 ± .002
(0,84 ± 0,05) DIA.
HOLE AFTER
PLATING
For rear view of 45°, 60° and 90°,
see circuit diagrams.
60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
Multi-Deck Rotary Switches
CIRCUIT DIAGRAMS: Solder Lug Terminals
Switch is Viewed From Shaft End and Shown in Position No. 1
Note: All common terminals are located above base terminals as shown.
11
C3
9
10
C1
6
1
6
5
2
ONE POLE
7
12
CL
1 C1
6
CL
1 C1
5
2
4
3
11
12
2
C2
3
TWO POLE
THREE POLE
C5
9 10
C4
9
8
C3
10 11
7
8
12
C4
CL
1 C1
6
5
2
4
3
4
7
6
1
2
5
C3
3
Series 08
36° Angle
of Throw
8
9
6
5
CL OF
NON-TURN
TAB
C2
C1
5
10
1
4
3
7
9
10 C
L
4
1
3
2
TWO POLE
4
1
7
6
C2
5
4
CL
1 C1
C1
2
C3 5
8
4
1
2
3
7
6
8
COMMON LUG
SINGLE POLE
CL
C1
15°
6
45°
2
3
7
4
5
8
C4
Rotary Switches
Rear Views
CL OF
NON-TURN
TAB
7
3
C1
2
5
Series 09
45° Angle
of Throw
8
6
ONE POLE
6
FIVE OR SIX POLE
8
7
CL
C1
3
C2
4
C2
FOUR POLE
C6
11
12
1
4
10
GRAYHILL
5
8
11
C2 7
12
7
9
8
2
8
Series 09
30° Angle
of Throw
CL OF
NON-TURN
TAB
10
3
9
C2
6
COMMON LUG
SINGLE POLE
6
5
6
4
3
3
2
C2
2
ONE POLE
TWO POLE
C OF
L
NON-TURN
TAB
4
CL
1 C1
CL
1 C1
C1
1
1
4
15°
2
C2
4
3
60°
2
THREE POLE
4
COMMON LUG
SINGLE POLE
4
2
ONE POLE
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
1 C1
2
15°
2
CL
C1
1
1
C2 3
3
3
Series 09
90° Angle
of Throw
5
6
4
Series 09
60° Angle
of Throw
C3
5
GRAYHILL
C OF
L
NON-TURN
TAB
5
THREE OR FOUR POLE
GRAYHILL
TWO POLE
3
ONE POLE
90°
TWO POLE
60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
Rotary
17
Multi-Deck Rotary Switches
SERIES 08
SERIES 09
.5" Diameter, 1/4 Amp, PC Mount
FEATURES
• Gold-plated Contact System
• 30°, 36°, 60° or 90° Angle of
Throw Options
• Compatible with Logic Level
Voltages and Currents
DIMENSIONS In inches (and millimeters)
PC Mount Style
Rear Views
Series 09
30° Angle of Throw
CL CL CL
2
3
4
5
1.200 ± .020
(30,48 ± 0,51)
TYP.
.562 (14,27) SER. 8
.625 (15,88) SER. 9
± .015 (0,38)
.125 + .001 – .002
(3,18 + 0,03 – 0,05)
DIA.
COMMON LUG
1/4-32 UNEF-2A THREAD
Note: Common location for a single pole per
deck switch. For common location on
multi-pole switches, see circuit diagrams.
2
3
10
9
7
Grayhill part number and date code marked on detent cover label. Customer
part number marked on request.
1
9
Special switches with one-sided termination can be made for circuitry which would
require two-sided termination in standard switches. Contact Grayhill for a special
part number. See also Special Options, page J-10.
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
.140 ± .015
(3,56 ± 0,38)
TYP.
.500 ± .020
(12,7 ± 0,51)
DIA.
*Termination
A standard switch uses the entire 360° of each deck as required by the circuitry.
Thus one-sided termination is standard for Series 08, 36°, 1 pole switches with 1 to
5 positions per pole; it is also standard for Series 09, 30°, 1 pole switches with 1 to
6 positions per pole. Two-sided termination is standard for 1 pole switches with more
positions per pole and for switches of 2 or more poles per deck.
Rotary
18
TERMINAL DIMENSIONS AT
THIS POINT ARE .032 + .000 – .010
(0,81 + 0,00 – 0,25) WIDE
BY .015 + .000 – .003
(0,38 + 0,00 – 0,08) THICK
4
SEE NOTE
INTEGRAL ASSEMBLY NUT,
DO NOT REMOVE
Series 08
36° Angle of Throw
GRAYHILL
NON-TURN TAB .062 ± .005
(1,58 ± 0,13) WIDE BY
.020 ± .003 (0,51 ± 0,08) THICK
GRAYHILL
.187 ± .015
(4,75 ± 0,38)
TYP.
#0 THREAD
5
.250 ± .020
(6,35 ± 0,51)
.134
± .010
(3,40
± 0,25)
6
.375 ± .020
(9,53 ± 0,51)
.134 ± .010
(3,40 ± 0,25)
11
8
CL OF NONTURN
TAB
6
.135 ± .015 (3,43 ± 0,38)
.588 ± .020
(14,73 ± 0,51)
12
1
DIM. B REF.
STUD
PROJECTION
9
Rotary Switches
.094 ± .010
(2,38 ± 0,25)
DIM. A + .046 – .020
(+ 0,05 – 0,51)
.312 ± .020
(7,92 ± 0,51)
10
.260 ± .015
(6,60 ± 0,38)
.070 ± .010
(1,78 ± 0,25)
TYP.
.140 ± .015
(3,56 ± 0,38)
TYP.
.562 ± .020
(14,27 ± 0,51)
DIA.
7
Front view shows terminal location of
36° angle of throw. Transpose rear
view for terminal location of 30° angle
of throw. See Circuit Diagrams for 60°
and 90° angles of throw.
.187 ± .015
(4,75 ± 0,38)
TYP.
1.125 ± .020
(28,58 ± 0,51)
TYP.
60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
Multi-Deck Rotary Switches
CIRCUIT DIAGRAMS: PC Mount
Switch is Viewed From Shaft End and Shown in Position No. 1
Note: All common terminals are located above base terminals as shown.
12
11
Series 09
30° Angle
of Throw
CL OF
NON-TURN
TAB
1
2
10
3
9
4
C1
8
Series 08
36° Angle
of Throw
10
3
9
4
8
8
10
C1
4
C1
4
6
C2
C2 8
3
C1 CL
C1 CL
2
4
3
3
TWO POLE
CL OF
NON-TURN
TAB
1
Series 09
90° Angle
of Throw
1
5
ONE POLE
2
4
1
C2
C1
4
C1 CL
2
2
4
7
5
6
ONE POLE
1
2
1
9
3
CL OF
NON-TURN
TAB
5
5
C OF
L
NON-TURN
TAB
2
6
C1 CL
TWO POLE
1
7
Series 09
60° Angle
of Throw
6
7
6
9
6
2
ONE POLE
10
1
C2
5
7
12
11
5
3
3
ONE POLE
TWO POLE
TWO POLE
PC BOARD MOUNTING PATTERN
36° Angle of Throw
30°, 60° and 90° Angle of Throw
.134 (3,40) TYP.
.134 (3,40) TYP.
.134 (3,40) TYP.
BASE TERMINAL
ROW HOLE LOCATION
(SEE CHART)
TYP.
E
1 Pole Per Deck
2 Poles Per Deck
C
D
SHAFT END
OF SWITCH
Number of Poles
Per Deck
Common Terminal
Hole Location
A
A
F
.140
(3,56)
TYP.
A
SHAFT END
OF SWITCH
B
C
E
D
.140
(3,56)
.070 TYP.
(1,78)
COMMON TERMINAL ROW
HOLE LOCATION (SEE CHART)
Angle of Throw
Base Terminals
Hole Location
30°
60°
90°
All
E and F
D and F
Diagrams shown for a two deck switch. Bushing mounting is
recommended for all PC mount rotary switches.
SHAFT AND PANEL SEAL
A shaft and panel seal is available to provide watertight mounting of the Series 08
and 09. Standard and Military Style rotary switches. Sealing is accomplished by
O-ring shaft seal and panel seal washer. When the panel seal is compressed,
dimensions are approximately the same as an unsealed switch. Sealed switches are
provided with a double flat bushing. Non-turn feature can be accomplished by proper
fit of this bushing into panel hole and/or by allowing non-turn tab to extend into (but
not through) panel. Military Style rotary sealed switches do not have a non-turn tab.
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
Rotary
19
Rotary Switches
.134 (3,40) TYP.
.210
.280 (5,33)
(7,11) TYP.
Multi-Deck Rotary Switches
MILITARY QUALIFIED
Switch Bases: Melamine per (MIL-M-14) ASTMD-5948
Cover, Deck Separators and End Plate: Phenolic
per (MIL-M-14) ASTM-D-5948
Rotor Mounting Plate: Thermoplastic
Mounting Bushing: Brass, tin/zinc-plated.
Shaft, Retaining Rings, Through Bolts, Shaft
Extension, Stop Washers, Stop Arm, Thrust
Washers, Nuts, Cover Plate and Rear Support
Plate: Stainless steel
Detent Balls: Steel, nickel-plated
Detent Springs: Tinned Music wire
Terminals, Stator (Base) Contacts and
Common Plate: Brass, gold plate .00001"
minimum over silver plate .0003" minimum
Rotor Contact: Silver alloy, gold-plated .00001"
minimum
Mounting Hardware: Two mounting nuts .062"
(1,57) thick by .312" (7,92) across flats and one
internal lockwasher are supplied with switch.
Lockwasher: Stainless steel
Mounting Nuts, Washers: Brass, tin/zincplated and or stainless steel.
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
10 9
1
36°
7
GRAYHILL
1 12
Materials and Finishes
Standard Style
GRAYHILL
2
Rotary
20
The Series 08M and 09M also meet the
requirements of MIL-DTL-3786 SR13 for moisture
resistance, stop strength, rotational torque,
vibration (10 to 2,000 cps), medium and high
shock, salt spray, explosion, thermal shock (65°C to 85°C) and terminal pull. When tested at
sea level, 25°C and 68% relative humidity with
failure criteria of 50 milliohms maximum contact
resistance and 500 Vac breakdown voltage, these
switches will make and break 250 mA at 28 Vdc
inductive (250 millihenries): 1/2 amp: at 28 Vdc
resistive: 1/2 amp; at 115 Vac: 60 Hz resistive for
10,000 cycles of operation.
3
The switches have also been tested at reduced
barometric pressure (70,000 feet), 25°C at
approximately 68% relative humidity to make and
break the following loads as stated in MIL-DTL3786/SR13. 50 milliamperes 28 Vdc resistive; 20
milliamperes 115 Vac resistive. When tested to
the above loads at the stated conditions, the
Series 08M and 09M switches meet the following
life-limiting criteria after 25,000 cycles of operation
in accordance with MIL-DTL-3786.
Contact Resistance: 50 milliohms maximum after
life
Insulation Resistance: 1,000 megaohms
minimum between terminals and shaft
Dielectric Strength: 500 Vac (atmospheric
pressure) and 350 Vac (reduced pressure)
between mutually insulated parts.
4
Qualified to the following MIL-DTL-3786/13
Circuit Values: (Also see Standard Style
description.) The Series 08M and 09M have been
tested to meet the requirements of MIL-S-3786,
Style SR13, the majority of which are listed. At
85°C, approximately 68% relative humidity and
sea level pressure, the switches have been tested
to make and break the following loads, as stated
in MIL-DTL-3786/SR13: 125 milliamperes at 28
Vdc resistive: 75 milliamperes at 115 Vac resistive.
SEE NOTE
30°
.094 ± .010
(2,38 ± 0,25)
Note: Common location for a single pole per
deck switch. For common location on
multi-pole switches, see circuit diagrams.
8
8
2
Electrical Ratings
Military Qualified
15°
10 9
4
Rotary Switches
Rated: To make and break the following loads:
1/4 amp, 115 Vac resistive; 1/4 amp, 6-28 Vdc
resistive; 20 mA, 115 Vdc resistive; 50 mA, 115
Vac inductive; 20 mA, 28 Vdc inductive; to carry
4 amps continuous.
Contact Resistance: After 25,000 cycles of
operation, 50 milliohms maximum
Insulation Resistance: 1,000 megohms
minimum between terminals and shaft
Voltage Breakdown: 1,000 Vac initially
(500 Vac or better after most environmental tests)
Life Expectancy: 50,000 mechanical cycles of
operation. Note: Actual life is determined by a
number of factors, including electrical loading,
rate of rotation and environment, as well as
maximum contact resistance, minimum insulation
resistance and minimum voltage breakdown
required at the end of life.
11
.500 ± .020
(12,7 ± 0,51)
DIA.
5
Electrical Ratings
Standard Style
CL OF NON-TURN
TAB
.718 ± .020
(18,24 ± 0,51)
OVER
TERMINALS
6
SPECIFICATIONS
.260 ± .015
(6,60 ± 0,38)
.562 ± .020
(14,27 ± 0,51)
DIA.
.781 ± .020
(19,83 ± 0,51)
OVER TERMINALS
Series 08
36° Angle of Throw
7 6 5
The military style is dimensionally the same as
the standard except for the solder lug. Convert
standard style switch drawings to military style
drawings by including this terminal detail and
changing the over-terminal dimensions shown
here. Grayhill can provide complete specification
drawings. Qualified switches can be ordered by
the Grayhill number or the "M" number; they will
be marked per MIL-DTL-3786/13.
Series 09
30° Angle of Throw
Front view shows terminal location of
Series 09, 30° angle of throw.
Transpose rear view for terminal location
of other angles of throw.
3
Series 08 and 09 military switches are qualified
to MIL-DTL-3786/13. They include 30°, 36°, 45°
and 60° angles of throw with solder lug terminals
in sealed and unsealed styles. See front and
rear views at right. Standard variations which do
not affect switch performance can also be marked
as qualified product–contact Grayhill.
Terminal Detail
.034 ± .003
(0,86 ± 0,08)
.068 ± .005
(1,73 ± 0,13)
Materials and Finishes
Military Qualified
Deck Separators, End Plate and Switch Bases:
Diallyl per (MIL-M-14) ASTM-D-5948
Rotor Mounting Plate: Thermoplastic
Mounting Bushing: Brass, tin/zinc-plated.
Shaft, Cover, Stop Plate, Retaining Ring,
Through Bolts, Shaft Extension, Stop Arm,
Thrust Washers, Cover Plate and Rear Support
Plate, Lockwashers and Nuts: Stainless steel
Detent Balls: Steel, nickel-plated
Detent Springs: Tinned music wire
Terminals, Stator (Base) Contacts and
Common Plate: Brass, gold plate .00001"
minimum over silver plate .0003" minimum
Rotor Contact: Silver alloy, gold-plated .00001"
minimum
Mounting Hardware: Two mounting nuts .062"
(1,57) thick by .312" (7,92) across flats and one
internal tooth lockwasher are supplied with this
switch.
Mounting Nuts, Washers: Brass, tin/zincplated and or stainless steel.
ADDITIONAL CHARACTERISTICS
Standard Style and Military Qualified
Contacts: Shorting or Non-shorting contacts
available in 30°, 36° and 45° angle of throw rotary
switches. Non-shorting contacts available in 60°
and 90° angle of throw switches. All are wiping
contacts with over 100 grams of contact force.
Stop Strength: 12 lb-inches minimum
Rotational Torque: 8-64 oz-in depending upon
the number of poles per deck and the number of
decks
Extended Studs: Switches of six decks or more
have longer studs with extra stud nuts for
recommended double end mounting.
60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
Multi-Deck Rotary Switches
CHOICES AND LIMITATIONS
Series
08
Style and Designation
Angle
of Throw
A = Standard
S = Standard, Shaft/Panel Seal
M = Military Style
MS = Style M, Shaft/Panel Seal
36°
P = Standard, PC Mount
SP = Style P, Shaft/Panel Seal
MP = Military Style, PC Mount
MSP = Style MP, Shaft/Panel Seal
A = Standard
S = Standard, Shaft/Panel Seal
M = Military Style
MS = Style M, Shaft/Panel Seal
Stops
01 thru 12
01 thru 09
01 thru 12
01 thru 09
1
2
02 thru 10
02 thru 05
Printed
Circuit
01 thru 12
01 thru 09
01 thru 12
01 thru 09
1
2
02 thru 10
02 thru 05
Solder
01 thru 12
01 thru 09
01 thu 06
01 thru 04
01 thru 03
01 thru 03
01 thru 12
01 thru 09
01 thru 06
01 thru 04
01 thru 03
01 thru 03
1
2
3
4
5
6
02 thru 12
02 thru 06
02 thru 04
02 or 03
02
02
Printed
Circuit
01 thru 12
01 thru 09
01 thru 12
01 thru 09
1
2
02 thru 12
02 thru 06
01 thru 12
01 thru 06
01 thru 04
01 thru 03
01 thru 12
01 thru 06
01 thru 04
01 thru 03
1
2
3
4
02 thru 08
02 thru 04
02
02
Not
Available
01 thru 06
01 thru 03
01 or 02
1
2
3
02 thru 006
02 or 03
02
Printed
Circuit
Not
Available
01 thru 06
01 thru 03
1
2
02 thru 06
02 or 03
Solder
Not
Available
01 thru 06
01 thru 03
1
2
02 thru 04
02
Printed
Circuit
Not
Available
01 thru 06
01 thru 03
1
2
02 thru 04
02
Fixed
Solder
A = Standard,
S = Standard, Shaft/Panel Seal
M = Military Style
MS = Style M, Shaft/Panel Seal
Number of
Positions/Pole
60°
P = Standard, PC Mount
SP = Style P, Shaft/Panel Seal
MP = Military Style, PC Mount
MSP = Style MP, Shaft/Panel Seal
A = Standard
S = Standard, Shaft/Panel Seal
90°
P = Standard, PC Mount
SP = Style, Shaft/Panel Seal
ORDERING INFORMATION
Series: determined by the angle of throw
Style*: Letter(s) from the Choices and Limitations chart
Angle of Throw: Must agree with Series Number
09A30–03–1–12N–F
Stop Arrangement: Add letter C or F to a one pole per deck switch with the maximum number of positions
for a stop between position 1 and the last position.
Type of Contacts: N = Non-shorting; S = Shorting
Positions Per Pole: Requires 02 positions as a minimum to the maximum allowable dependent on the angle
of throw and poles per deck
Poles Per Deck: As limited by angle of throw and switch style
Number of Decks: As limited by the angle of throw, the poles per deck, switch style and types of contacts
* All rotary switches that are required to have military designated markings and testing adhering to MIL-3786 are to be ordered by specifying
the military part number identified on the appropriate slash sheet.
Available from your local Grayhill Distributor
For prices and discounts, contact a Local Sales Office, an authorized local Distributor or Grayhill.
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
Rotary
21
Rotary Switches
45°
Poles
Per Deck
Solder
30°
A = Standard,
S = Standard, Shaft/Panel Seal
M = Military Style
MS = Style M, Shaft/Panel Seal
Number of Decks
Shorting Non-Shorting
Fixed
P = Standard, PC Mount
SP = Style P, Shaft/Panel Seal
MP = Military Style, PC Mount
MSP = Style MP, Shaft/Panel Seal
09
Terminals