PE60 www.vishay.com Vishay Sfernice Power Panel 6 W Potentiometer FEATURES • High power rating 6 W at 50 °C • Cermet element • Full sealing • Mechanical strength • Industrial and professional grade • Tests according to CECC 41000 or IEC 60393-1 • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02") PE 60 L PE 60 F FR = 50 (1.969) 150 (5.872) min. Ø 25 18 (0.709) FG = 16 GR = 50.8 (2) 150 (5.872) min. FL = 25 (0.984) (0.630) 8 18 (0.709) GB = 12.7 (1/2) GJ = 22.22 (7/8) Ø6 (0.236) Ø 6.35 (0.250) Slot 1 x 1.8 deep Thread M 10 x 75 (0.039 x 0.071) 12 (0.472) Thread 3/8 32-UNEF-2A 9.52 Wrench = 14 (0.551) OPTION D: DBAN SHAFT LOCKING Slot 1 x 1.8 deep (0.039 x 0.071) (3/8) Wrench = 12.5 (0.492) OPTION L: PE 60 LPRP - WITH LOCATING PEG Wrench = 14 (0.551) Ø6 (0.236) 0.8 (0.031) 3 (0.118) Wrench = 12 (0.472) 12.5 (0.492) 9.2 (0.362) Ø 1.8 (0.071) 2.3 (0.091) 3 (0.118) 6.5 (0.256) Available on PE 60 L and PE 60 F 15 (0.591) Available only with PE 60 L Panel sealed version PE 60 M OPTION E: Including locating peg (available only for PE 60 M) 8 ± 0.2 (0.315 ± Ø 1.2 0.008) (0.047) Ø 10.5 (0.413) 21 (0.825) 0.7 (0.028) 9 (0.356) Flat located Ø6 (0.236) Sealing ring FD = 13 (0.514) FJ = 22 (0.868) FP = 47 (1.852) Available only with bushing M10 x 0.75 and shafts Ø 6 mm Revision: 25-Mar-15 Document Number: 51005 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PE60 www.vishay.com Vishay Sfernice ELECTRICAL SPECIFICATIONS Resistive Element Cermet Electrical Travel Resistance Range 270° ± 10° 1 to 1 M Linear Taper 100 to 2.2 M Logarithmic Taper Standard Series e3 Tolerance 1 - 2 - 2.5 - 5 Standard ± 20 % On Request ± 10 % % TOTAL RESISTANCE 100 Taper 80 F 60 A L 40 20 0 0 20 40 60 80 100 % CLOCKWISE SHAFT ROTATION Yellow Green (3) (1) Circuit Diagram CW (2) Red LIN. TAPER “A” Power Rating Linear Logarithmic 6 W at 50 °C 3 W at 50 °C POWER IN W 6 LOG. TAPER “L and F” 3 0 0 20 40 60 70 80 100 125 140 AMBIENT TEMPERATURE IN °C Temperature Coefficient See Standard Resistance Element Data Limiting Element Voltage (Linear Taper) 350 V Contact Resistance Variation (Linear Taper) 3 % Rn or 1 % 0.5 or 1 % End Resistance (Typical) Dielectric Strength (RMS) 2500 V Insulation Resistance (500 VDC) 105 M MECHANICAL SPECIFICATIONS Mechanical Travel ENVIRONMENTAL SPECIFICATIONS 300° ± 5° Temperature Range Operating Torque (Typical) 3 Ncm max. Climatic Category End Stop Torque 70 Ncm max. Sealing Tightening Torque of Mounting Nut Unit Weight Revision: 25-Mar-15 -55 °C to +125 °C 55/125/56 Fully sealed - Container IP67 250 Ncm 25 g to 35 g max. Document Number: 51005 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PE60 www.vishay.com Vishay Sfernice OPTIONS Length is measured from the mounting surface to the free end of the shaft. The screwdriver slot is aligned with the wiper within ± 10°. Special shafts are available, in accordance to drawings supplied by customers. We recommend that customers should not machine shafts, in order to avoid damage. The panel sealing device consists of a ring located in a groove on the potentiometer face. Sealing is obtained by tightening the ring against the panel when mounting the potentiometer. The shaft locking device consists of a tapered nut tightening a slotted notched washer against both bushing and shaft. DBAN tightening torque is 200 Ncm, shaft locking torque being 30 Ncm. DBAN is also available with all special types. This device is normally supplied in a separate bag. Can be pre-mounted on request. Location is obtained by fitting a special washer on the potentiometer face. The peg can therefore be positioned at 90°, 180°, 270° and 360°. Command Shaft Panel Sealing: PE60M Shaft Locking: DBAN Locating Peg: LPRP PERFORMANCE TESTS TYPICAL VALUES AND DRIFTS CONDITIONS RT/RT (%) R1-2/R1-2 (%) OTHER ±3% - Contact res. variation: < 3 % Rn ± 0.5 % ±1% - Damp Heat, Staedy State 1000 h at rated power 90’/30’ - ambient temp. 25 °C Phase A dry heat 125 °C Phase B damp heat Phase C cold -55 °C Phase D damp heat 5 cycles 56 days ± 0.5 % ±1% Insulation resistance: > 104 M Change of Temperature 5 cycles, -55 °C at +125 °C ± (0.5 % ± 0.1 ) - - Mechanical Endurance 25 000 cycles 50 g’s at 11 ms, 3 successive shocks in 3 directions 10 Hz to 55 Hz, 0.75 mm or 10 g’s during 6 h ±3% - Contact res. variation: < 5 % Rn ± 0.1 % ± 0.2 % - ± 0.1 % ± 0.2 % - Electrical Endurance Climatic Sequence Shock Vibration Note • Nothing stated herein shall be construed as a guarantee of quality or durability. STANDARD RESISTANCE ELEMENT DATA STANDARD MAX. RESISTANCE POWER VALUES at 50 °C LINEAR TAPER TYPICAL TCR MAX. MAX. CUR. - 55 °C WORKING THROUGH + 125 °C VOLTAGE WIPER W V mA 1 2 5 10 20 25 50 100 200 250 500 1K 2K 2.5K 5K 10K 20K 25K 50K 100K 200K 250K 500K 1M 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 4.90 2.45 1.23 0.61 0.49 0.25 0.12 2.4 3.5 5.5 7.7 11.0 12.2 17.3 24.5 34.6 38.7 54.8 77.5 110 122 173 245 346 350 350 350 350 350 350 350 2449 1732 1095 775 548 490 346 245 173.2 154.9 109.5 77.5 54.8 49.0 34.64 24.49 17.32 14.00 7.00 3.50 1.75 1.40 0.70 0.35 Revision: 25-Mar-15 ppm/°C MARKING Printed: - Vishay trademark - Part number - Manufacturing date PACKAGING ± 500 - In box of 5 pieces ± 250 Document Number: 51005 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PE60 www.vishay.com Vishay Sfernice ORDERING INFORMATION (part number) P E 6 0 L 0 F G W 2 MODEL BUSHING OPTION SHAFT LEADS PE60 M = Panel sealed L = STD F = 3/8" 0 = None For L bushing FG 16 mm, slotted FL 25 mm, slotted FR 50 mm, plain W: Wire For L bushing D = DBAN L = LPRP B = DBAN and LPRP For F bushing L = LPRP For M bushing E = Peg 0 OHMIC VALUE 204 = 200 k 4 M A TOLERANCE TAPER ± 20 % On request: ± 10 % ±5% A = Linear L = Clockwise logarithmic F = Clockwise inverse logarithmic For F bushing GB 1/2", slotted GJ 7/8", slotted GR 2", slotted SPECIAL NUMBER (if applicable) Given by Vishay for custom design For M bushing FD = 13 mm, slotted FJ = 22 mm, slotted FP = 47 mm, plain PART NUMBER DESCRIPTION (for information only) PE60 L 0 FG W 200 k 20 % A BO5 MODEL BUSHING OPTION SHAFT LEADS OHMIC VALUE TOL. TAPER PACKAGING Revision: 25-Mar-15 e4 SPECIAL SPECIAL LEAD (Pb)-FREE Document Number: 51005 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000