SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents Standard Metal Film Leaded Resistors FEATURES • Small size (SFR16S: 0204, SFR25 / SFR25H: 0207) • Low noise (max. 1.5 μV/V for R > 1 M) • Compatible to both lead (Pb)-free and lead containing soldering processes • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • General purpose resistors A homogeneous film of metal alloy is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned connecting leads of electrolytic copper are welded to the end-caps. The resistors are coated with a colored lacquer (light-blue for type SFR16S; light-green for type SFR25 and red-brown for type SFR25H) which provides electrical, mechanical, and climatic protection. The encapsulation is resistant to all cleaning solvents in accordance with IEC 60068-2-45. TECHNICAL SPECIFICATIONS DESCRIPTION DIN size Resistance range SFR16S SFR25 SFR25H 0204 0207 0207 1 to 3 M; Jumper (0 0.22 to 10 M; Jumper (0 0.22 to 10 M Resistance tolerance ± 5 %; ± 1 % Temperature coefficient Rated dissipation, P70 Thermal resistance Operating voltage, Umax. AC/DC ± 250 ppm/K; ± 100 ppm/K 0.5 W 0.4 W 0.5 W 170 K/W 200 K/W 150 K/W 200 V 250 V 350 V Operating temperature range -55 °C to 155 °C Permissible film temperature 155 °C Max. resistance range at rated dissipation |R/R max.|, after 1000 h ± (2 % R + 0.05 ) Note • R value is measured with probe distance of 24 mm ± 1 mm using 4-terminal method. Revision: 13-May-15 Document Number: 28722 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE TOLERANCE ±5% TCR RESISTANCE ± 250 ppm/K 1 to 4.7 ± 100 ppm/K 4.7 to 100 k ± 250 ppm/K > 100 k to 3 M ± 100 ppm/K 5.6 to 100 k ± 250 ppm/K > 100 k to 3 M - 30 m; Imax. = 3 A ± 250 ppm/K 0.22 to 4.7 ± 100 ppm/K > 4.7 to 1 M ± 250 ppm/K > 1 M to 10 M ± 250 ppm/K 1 to 4.7 ± 100 ppm/K > 4.7 to 1 M ± 250 ppm/K > 1 M to 10 M - 30 m; Imax. = 5 A SFR16S E-SERIES E24 ±1% E24; E96 Jumper (0 - ±5% E24 SFR25, SFR25H ±1% E24; E96 Jumper (0 ) (1) - Note (1) Jumper is only available for SFR25. PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: SFR2500001001FA500 S F R 2 5 0 0 0 0 1 0 0 1 F A 5 0 0 TYPE VARIANT TCR/MATERIAL RESISTANCE TOLERANCE PACKAGING SPECIAL SFR16S0 SFR2500 SFR25H0 0 = neutral Z = value overflow (special) 0 = standard Z = jumper 3 digit value 1 digit multiplier MULTIPLIER F=±1% J=±5% Z = jumper N4 A5 A1 R5 The 2 digits are used for all special parts. 00 = standard 7 = *10-3 8 = *10-2 9 = *10-1 0 = *100 1 = *101 2 = *102 3 = *103 4 = *104 5 = *105 Z = 0000 PRODUCT DESCRIPTION: SFR25 1 % A5 1K0 SFR25 1% TYPE TOLERANCE SFR16S SFR25 SFR25H ±1% ±5% A5 PACKAGING 1K0 (1) N4 A5 A1 R5 RESISTANCE VALUE 47K = 47 k 51R1 = 51.1 Notes • The products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER. • N4 packaging indicates SFR25 and SFR25H radial version. Revision: 13-May-15 Document Number: 28722 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents PACKAGING TYPE SFR16S CODE QUANTITY PACKAGING STYLE WIDTH PITCH DIMENSIONS A5 5000 Taped acc. to IEC 60286-1 fan-folded in a box R5 5000 Taped acc. to IEC 60286-1 on a reel A1 (1) 1000 Taped acc. to IEC 60286-1 fan-folded in a box 75 mm x 28 mm x 262 mm A5 5000 Taped acc. to IEC 60286-1 fan-folded in a box 75 mm x 98 mm x 270 mm R5 5000 Taped acc. to IEC 60286-1 on a reel A1 (1) 1000 Taped acc. to IEC 60286-1 fan-folded in a box N4 (2) 4000 Taped acc. to IEC 60286-2 fan-folded in a box 75 mm x 73 mm x 270 mm 52 mm 52 mm 5 mm 5 mm 92 mm x 278 mm x 278 mm 93 mm x 300 mm x 298 mm SFR25, SFR25H 75 mm x 28 mm x 262 mm - 12.7 mm 45 mm x 262 mm x 330 mm Notes (1) A1 packaging only available for resistors with ± 5 % tolerance. (2) N4 packaging only available for SFR25 and SFR25H radial version. MARKING The nominal resistance and tolerance are marked on the resistor using four or five colored bands in accordance with IEC 60062, marking codes for resistors and capacitors. Revision: 13-May-15 Document Number: 28722 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents Power in % FUNCTIONAL PERFORMANCE 100 80 60 40 20 0 -55 0 50 100 70 125 155 180 Ambient Temperature in °C Derating Maximum dissipation (Pmax.) in percentage of rated power as a function of the ambient temperature (Tamb) 90 100 ΔT (K) ΔT (K) SFR25 80 70 60 SFR25H 50 40 30 20 10 0 0.2 0.4 P (W) 0.6 SFR16S Hot-spot temperature rise (T) as a function of dissipated power 0 0.1 0.2 0.3 0.5 0.4 P (W) SFR25/SFR25H Hot-spot temperature rise (T) as a function of dissipated power Note • The maximum permissible hot-spot temperature is 155 °C. Revision: 13-May-15 Document Number: 28722 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents 103 Pmax. (W) 102 10 t p /ti = 1000 500 200 100 50 20 10 5 2 1 10-1 10-6 10-5 10-4 10-3 10-2 10-1 t i (s) 1 SFR16S Pulse on a regular basis; maximum permissible peak pulse power ( P max.) as a function of pulse duration (ti) 600 Umax. (V) 500 400 300 200 100 0 10-6 10-5 10-4 10-3 10-2 10-1 t i (s) 1 SFR16S Pulse on a regular basis; maximum permissible peak pulse voltage ( U max.) as a function of pulse duration (ti) 103 Pmax. (W) 102 10 t p /t i = 1000 500 200 100 50 20 10 5 1 10-1 10-6 2 10-5 10-4 10-3 10-2 10-1 t i (s) 1 SFR25 Pulse on a regular basis; maximum permissible peak pulse power ( P max.) as a function of pulse duration (ti) Revision: 13-May-15 Document Number: 28722 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents 600 Umax. (V) 500 400 300 200 100 0 10-6 10-5 10-4 10-3 10-2 10-1 t i (s) 1 SFR25 Pulse on a regular basis; maximum permissible peak pulse voltage ( U max.) as a function of pulse duration (ti) 103 Pmax. (W) t p /t i = 1000 500 200 100 50 102 10 20 10 5 2 1 10-1 10-6 10-5 10-4 10-3 10-2 10-1 t i (s) 1 SFR25H Pulse on a regular basis; maximum permissible peak pulse power ( P max.) as a function of pulse duration (ti) 1200 h Umax. (V) 800 400 0 10-6 10-5 10-4 10-3 10-2 10-1 t i (s) 1 SFR25H Pulse on a regular basis; maximum permissible peak pulse voltage ( U max.) as a function of pulse duration (ti) Revision: 13-May-15 Document Number: 28722 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents TESTS PROCEDURES AND REQUIREMENTS All tests are carried out in accordance with the following specifications: Unless otherwise specified the following values apply: • EN 60115-1, generic specification (includes tests) • Relative humidity: 45 % to 75 % The test and requirements table contains only the most important tests. For the full test schedule refer to the documents listed above. • Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). The tests are carried out in accordance with IEC 60068-2-xx test method and under standard atmospheric conditions in accordance with IEC 60068-1, 5.3. • Temperature: 15 °C to 35 °C For performing some of the tests, the components are mounted on a test board in accordance with IEC 60115-1, 4.31. In test procedures and requirements table, only the tests and requirements are listed with reference to the relevant clauses of IEC 60115-1 and IEC 60068-2-xx test methods. A short description of the test procedure is also given. TEST PROCEDURES AND REQUIREMENTS IEC 60115-1 CLAUSE 4.5 4.8 4.12 4.13 IEC 60068-2 TEST METHOD - - - TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (Rmax.) Resistance - ± 5 %; ± 1 % Temperature coefficient At (20 / -55 / 20) °C Noise ± 250 ppm/K; ± 100 ppm/K and (20 / 155 / 20) °C IEC 60195 Short time overload Room temperature; U = 2.5 x or U = 2 x Umax.; 5 s Robustness of terminations Tensile, bending, and torsion < 68 k 68 k to 100 k > 100 k to 1 M > 1 M SFR16S ≤ 0.1 μV/V ≤ 0.5 μV/V ≤ 1.5 μV/V ≤ 1.5 μV/V SFR25, SFR25H ≤ 0.1 μV/V ≤ 0.1 μV/V ≤ 0.1 μV/V ≤ 1.5 μV/V SFR16S, SFR25 ± (0.25 % R + 0.05 ) SFR25H ± (1 % R + 0.05 ) 21 (Ua1) 4.16 21 (Ub) ± (0.25 % R + 0.05 ) 21 (Uc) at +235 °C; 2 s; solder bath method; SnPb40 4.17 20 (Ta) Solderability 4.18 20 (Tb) Resistance to soldering heat Unmounted components (260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 ) 4.19 14 (Na) Rapid change of temperature 30 min at -55 °C and 30 min at +155 °C; 5 cycles ± (0.25 % R + 0.05 ) 4.20 29 (Eb) Bump 3 x 1500 bumps in 3 directions; 40 g ± (0.25 % R + 0.05 ); no damage 4.22 6 (Fc) Vibration 10 sweep cycles per direction; 10 Hz to 2000 Hz 1.5 mm or 200 m/s2 ± (0.25 % R + 0.05 ); no damage 4.23.3 Good tinning (≥ 95 % covered); no damage Climatic sequence: 4.23 4.23.2 at +245 °C; 3 s; solder bath method; SnAg3Cu0.5 2 (Ba) Dry heat 155 °C; 16 h 30 (Db) Damp heat, cyclic 90 % to 100 % RH; 1 cycle 55 °C; 24 h; 4.23.4 1 (Aa) Cold -55 °C; 2 h 4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; 15 °C to 35 °C 4.23.6 30 (Db) Damp heat, cyclic 55 °C; 5 days; 95 % to 100 % RH; 5 cycles DC load apply rated power for 1 min 4.23.7 Revision: 13-May-15 SFR16S, SFR25, SFR25H ± (1 % R + 0.05 ); no visible damage ± (1 % R + 0.05 ); no visible damage ± 2 % R; no visible damage Document Number: 28722 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents TEST PROCEDURES AND REQUIREMENTS IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (Rmax.) 4.24 78 (Cab) Damp heat (steady state) (40 ± 2) °C; 56 days; (93 ± 3) % RH ± (2 % R + 0.05) Endurance 4.25.1 (at 70 °C) U = P 70 x R or U = Umax.; 1.5 h on; 0.5 h off 70 °C; 1000 h ± (2 % R + 0.05 ) DIMENSIONS L1 Ød ØD Outline L2 DIMENSIONS - Leaded resistor types, mass and relevant physical dimensions Ø Dmax. (mm) L1 max. (mm) L2 max. (mm) Ød (mm) MASS (mg) SFR16S 1.9 3.5 4.1 0.45 ±0.05 102 SFR25 2.5 6.5 7.5 0.58 ±0.05 205 SFR25H 2.5 6.5 7.5 0.58 ±0.05 205 TYPE SFR25, SFR25H WITH RADIAL TAPING P2 DIMENSIONS in millimeters P H1 H H0 L L1 W0 W α α F α = 30° to 40° a a Revision: 13-May-15 P0 P1 D0 Pitch of components P 12.7 ± 1.0 Feed-hole pitch P0 12.7 ± 0.2 Feed-hole center to lead at topside at the tape P1 3.85 ± 0.5 Feed-hole center to body center P2 6.35 ± 1.0 Lead-to-lead distance F 4.8 + 0.7 / - 0 Tape width W 18.0 ± 0.5 Minimum hold down tape width W0 5.5 Maximum component height H1 29 Lead wire clinch height H0 16.5 ± 0.5 Height of component from tape center H 19.5 ± 1 Feed-hole diameter D0 4.0 ± 0.2 Maximum length of snipped lead L 11.0 Minimum lead wire (tape portion) shortest lead L1 2.5 Note • Please refer to document “Packaging” for more detail (www.vishay.com/doc?28721). Document Number: 28722 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFR16S, SFR25, SFR25H www.vishay.com Vishay BCcomponents HISTORICAL 12NC INFORMATION Resistance Decade for ± 1 % Tolerance • The resistors had a 12-digit numeric code starting with 23. RESISTANCE DECADE LAST DIGIT • The subsequent 6 digits for 1 % or 7 digits for 5 % indicated the resistor type and packaging. 1 to 9.76 8 • The remaining digits indicated the resistance value: -The first 3 digits for 1 % or 2 digits for 5 % indicated the resistance value. -The last digit indicated the resistance decade. Resistance Decade for ± 5 % Tolerance RESISTANCE DECADE LAST DIGIT 0.10 to 0.91 7 1 to 9.1 8 10 o 91 9 100 to 910 1 1 k to 9.1 k 2 10 k to 91 k 3 100 k to 910 k 4 1 M to 9.1 M 5 = 10 M 6 10 to 97.6 9 100 to 976 1 1 k to 9.76 k 2 10 k to 97.6 k 3 100 k to 976 k 4 1 M to 9.76 M 5 = 10 M 6 12NC Example The 12NC of a SFR25 resistor, value 5600 ± 5 %, taped on a bandolier of 5000 units in ammopack was: 2322 181 43562. HISTORICAL 12NC - Resistor type and packaging 23.. ... ..... BANDOLIER IN AMMOPACK TYPE RADIAL TAPED SFR16S SFR25 BANDOLIER ON REEL TOL. STRAIGHT LEADS STRAIGHT LEADS 4000 UNITS 1000 UNITS 5000 UNITS 5000 UNITS ±5% - ..22 187 73... ..22 187 53... ..06 187 23... ±1% - - ..06 187 3... ..06 187 1.... Jumper - - ..06 187 90013 ..22 187 90346 ±5% ..06 184 03... ..22 181 53... ..22 181 43... ..22 181 63... ±1% - - ..22 188 2... ..06 181 8.... Jumper - ..22 181 90018 ..22 181 90019 ..06 181 90011 ±5% ..06 186 03... ..22 186 16... ..22 186 76... ..06 186 63... ±1% - - ..22 186 3.... ..06 186 8.... SFR25H Revision: 13-May-15 Document Number: 28722 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000