VOR1142M4 www.vishay.com Vishay Semiconductors 1 Form A Solid-State Relay FEATURES • Current limit protection 1 A 4 • Isolation test voltage 3750 VRMS S1 • Typical RON 22 • Load voltage 400 V C 2 3 • Load current 140 mA S2 • High surge capability • Clean bounce free switching • Low power consumption • High temperature range DESCRIPTION • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 The VOR1142 is an SPST normally open switch (1 form A) that can replace electromechanical relays in many applications. It is constructed using a GaAlAs IRED actuation control and MOSFETs for the switch output. APPLICATIONS • General telecom switching • Medical • Metering • Security • Instrumentation • Industrial controls AGENCY APPROVALS • UL1577, file no. E52744 (certificate pending) • DIN EN 60747-5-5 (VDE0884-5) (certificate pending) ORDERING INFORMATION V O R 1 PART NUMBER PACKAGE 1 4 2 M 4 SOP-4 # PACKAGE CONFIGURATION 7.21 mm UL, VDE SOP-4, tape and reel VOR1142M4T SOP-4, tube VOR1142M4 Rev. 1.0, 25-Aug-15 Document Number: 84301 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOR1142M4 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER CONDITIONS SYMBOL VALUE UNIT IRED continuous forward current IF 50 mA IRED reverse voltage VR 5 V Pdiss 80 mW DC or peak AC load voltage VL 400 V Continuous DC load current IL 140 mA Pdiss 550 mW Ambient temperature range (1) Tamb -40 to +100 °C Storage temperature range Tstg -40 to +150 °C Tsld 260 °C INPUT Input power dissipation OUTPUT SSR output power dissipation SSR Soldering temperature t = 10 s max. Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) For continuous negative potential from output side to input side only 85 °C is allowed. ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT IRED forward current, switch turn-on IL = 100 mA, t = 10 ms IFon - 0.25 2 mA IRED forward current, switch turn-off VL = ± 350 V, IL < 1 μA IFoff 0.05 0.15 - mA IRED forward voltage IF = 10 mA VF - 1.36 1.5 V IRED reverse current VR = 5 V IR - - 10 μA OUTPUT On-resistance IF = 5 mA, IL = 50 mA RON - 22 27 Off-resistance IF = 0 mA, VL = ± 100 V ROFF 0.5 850 - G Off-state leakage current Output capacitance Current limit AC/DC IF = 0 mA, VL = ± 100 V Ileak - <1 100 nA IF = 0 mA, VL = ± 400 V Ileak - 6 500 nA IF = 0 mA, VL = 1 V, 1 MHz CO - 39 - pF IF = 0 mA, VL = 50 V, 1 MHz CO - 6 - pF IF = 5 mA, t = 5 ms, VL = ± 6 V Ilimit 170 300 450 mA VIO = 1 V CIO - 0.4 - pF COUPLER Capacitance (input to output) Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. Rev. 1.0, 25-Aug-15 Document Number: 84301 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOR1142M4 www.vishay.com Vishay Semiconductors SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Turn-on time IF = 5 mA, IL = 50 mA ton - 0.2 0.5 ms Turn-off time IF = 5 mA, IL = 50 mA toff - 0.05 0.2 ms Input 1 4 C 2 3 A 90 % VL Output 10 % Output ton toff Fig. 1 - Timing Schematic SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION Climatic classification According to IEC 68 part 1 Pollution degree According to DIN VDE 0109 Comparative tracking index SYMBOL VALUE UNIT 40/100/21 2 CTI 175 Maximum rated withstanding isolation voltage According to UL1577, t = 1 min VISO 3750 Maximum transient isolation voltage According to DIN EN 60747-5-5 VIOTM 6000 Vpeak Maximum repetitive peak isolation voltage According to DIN EN 60747-5-5 VIORM 707 Vpeak Tamb = 25 °C, VIO = 500 V RIO 1012 Tamb = 100 °C, VIO = 500 V RIO 1011 PSO 550 mW Input safety current ISI 180 mA Input safety temperature TS 175 °C Isolation resistance Output safety power VRMS Clearance distance SOP-4 5 mm Creepage distance SOP-4 5 mm DTI 0.3 mm Input to output test voltage, method B VIORM x 1.875 = VPR, 100 % production test with tM = 1 s, partial discharge < 5 pC VPR 1326 Vpeak Input to output test voltage, method A VIORM x 1.6 = VPR, sample test with tM = 10 s, partial discharge < 5 pC VPR 1131 Vpeak Insulation thickness Note • As per IEC 60747-5-5, §7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. Rev. 1.0, 25-Aug-15 Document Number: 84301 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOR1142M4 www.vishay.com Vishay Semiconductors PSO - Output Safety Power (mW) ISI - Input Safety Current (mA) 250 200 150 100 50 0 -50 -25 0 25 50 800 600 400 200 0 -50 -25 75 100 125 150 175 Tamb - Ambient Temperature (°C) 0 25 50 75 100 125 150 175 Tamb - Ambient Temperature (°C) Fig. 2 - Safety Input Current vs. Ambient Temperature Fig. 3 - Safety Power Dissipation vs. Ambient Temperature TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 60 160 IF - Forward Current (mA) IL - Load Current (mA) 140 120 100 80 60 40 20 IF > 5 mA 50 Tamb = 100 °C 40 Tamb = 25 °C 30 Tamb = -40 °C 20 10 0 0 -40 -20 0 20 40 60 80 0 100 120 0.5 Tamb - Ambient Temperature (°C) Fig. 4 - Maximum Load Current vs. Ambient Temperature 1.5 2.0 Fig. 6 - Forward Current vs. Forward Voltage 1.7 2.5 Normalized Forward Current for Switch Turn-On VF - Forward Voltage (V) 1.0 VF - Forward Voltage (V) 1.6 1.5 IF = 10 mA 1.4 1.3 1.2 IF = 2 mA IF = 5 mA 1.1 1.0 -40 -20 0 20 40 60 80 100 Tamb - Ambient Temperature (°C) Fig. 5 - Forward Voltage vs. Ambient Temperature Rev. 1.0, 25-Aug-15 IL = 100 mA 2.0 1.5 1.0 0.5 Normalized to Tamb = 25 °C 0 -40 -20 0 20 40 60 80 100 Tamb - Ambient Temperature (°C) Fig. 7 - Normalized Forward Current for Switch Turn-On vs. Ambient Temperature Document Number: 84301 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOR1142M4 www.vishay.com Vishay Semiconductors 0.5 0.4 1.0 0.8 0.6 0.4 0.3 T = 25 °C 0.2 T = -40 °C 0.1 0.2 Normalized to Tamb = 25 °C 0 0 -40 -20 0 20 40 60 80 100 0 10 Tamb - Ambient Temperature (°C) 30 40 50 Fig. 11 - Turn-On Time vs. Forward Current 60 1.8 IF = 0 mA f = 1 MHz 50 Normalized Turn-On Time CO - Output Capacitance (pF) 20 IF - Forward Current (mA) Fig. 8 - Normalized On-Resistance vs. Ambient Temperature 40 30 20 10 0 1.6 IF = 5 mA 1.4 1.2 1.0 0.8 0.6 0.4 0.2 Normalized to Tamb = 25 °C 0 0 10 20 30 40 50 60 -40 VL - Load Voltage (V) -20 0 20 40 60 80 100 Tamb - Ambient Temperature (°C) Fig. 9 - Output Capacitance vs. Load Voltage Fig. 12 - Normalized Turn-On Time vs. Ambient Temperature 100 0.20 IL = 50 mA IF = 0 mA T = 100 °C T = 100 °C 0.16 10 Turn-Off Time (ms) Off-State Leakage Current (nA) IL = 50 mA T = 100 °C IF = 5.0 mA IL = 50 mA 1.2 Turn-On Time (ms) Normalized On-Resistance 1.4 T = 25 °C 1 0.1 0.12 T = 25 °C 0.08 0.04 T = -40 °C T = -40 °C 0.01 0 0 100 200 300 400 VL - Load Voltage (V) Fig. 10 - Off-State Leakage Current vs. Load Voltage Rev. 1.0, 25-Aug-15 0 10 20 30 40 50 IF - Forward Current (mA) Fig. 13 - Turn-Off Time vs. Forward Current Document Number: 84301 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOR1142M4 www.vishay.com Vishay Semiconductors Normalized Turn-Off Time 1.8 1.6 1.4 1.2 IF = 5 mA 1.0 0.8 0.6 0.4 0.2 Normalized to Tamb = 25 °C 0 -40 -20 0 20 40 60 80 100 Tamb - Ambient Temperature (°C) Fig. 14 - Normalized Turn-Off Time vs. Ambient Temperature PACKAGE DIMENSIONS (in millimeters) 6.95 ± 0.25 5.35 typ. 4.57 ± 0.25 0.2 ± 0.05 4.42 ± 0.25 0.05 ± 0.05 2.12 ± 0.2 4.92 max. 5 min. 0.41 ± 0.1 0.5 ± 0.15 2.54 nom. Leads coplanarity 0.1 max. 4 3 technical drawings according to DIN specifications PIN ONE I.D. 0.9 2.54 Recommended footprint 1.15 5.1 1 7.4 2 Drawing-No.: 6.544-5415.01-4 Issue: 2; 23.07.12 Fig. 15 - Package Drawing Rev. 1.0, 25-Aug-15 Document Number: 84301 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VOR1142M4 www.vishay.com Vishay Semiconductors PACKAGE MARKING 1142 V YWW 68 Fig. 16 - VOR1142M4 Note • Package configuration (T, M) are not part of the package marking. PACKAGING INFORMATION (in millimeters) 2.0 ± 0.1 4.0 ± 0.1 1.5 ± 0.1 Pin 1 1.75 ± 0.1 0.35 ± 0.05 5.5 ± 0.1 12.0 ± 0.3 CL 7.33 ± 0.1 7.33 ± 0.1 8.0 ± 0.1 4.72 ± 0.1 1.5 ± 0.1 2.36 ± 0.1 2.66 ± 0.1 Note: • Cummulative tolerance of 10 spocket holes is 0.20 mm Fig. 17 - Tape and Reel Packing (2000 pieces on reel) DEVICE PER TUBE TYPE UNITS/TUBE TUBES/BOX UNITS/BOX SOP-4 100 40 4000 SOLDER PROFILES HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 300 Temperature (°C) max. 260 °C 245 °C 255 °C 240 °C 217 °C 250 Floor life: unlimited Conditions: Tamb < 30 °C, RH < 85 % Moisture sensitivity level 1, according to J-STD-020 200 max. 30 s 150 max. 100 s max. 120 s 100 max. ramp down 6 °C/s 50 max. ramp up 3 °C/s 0 0 19841 50 100 150 200 250 300 Time (s) Fig. 18 - Lead (Pb)-free Reflow Solder Profile According to J-STD-020 for SMD Devices Rev. 1.0, 25-Aug-15 Document Number: 84301 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000