Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED ·Customer: Technical Data Sheet PN: 3751XG2D-S For: IF=20mA Contents 1.Features 2.Applications 3.Package dimensions 4.Absolute maximum rating 5.Electrical optical characteristics 6. Ranks Combination 7.Soldering conditions 8.Typical electro-optical characteristics curves 9.Reliability 10.Cautions 11.Notes Customer confirm Prepared date：Oct. 2010 Approved by Checked by www.ledz.com Issued by Rev.：1 Page 1 of 8 Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED Part No. Emitted 3751XG2D-S Color Green Chip Material Face Color InGaN/GaN Green Diffused Viewing Angle 105/55 ◆ Features: Compatible with automatic placement equipment Compatible with reflow solder process Low power consumption This product doesn’t contain restriction Substance, comply ROHS standard. ◆ Applications: Automotive and Telecommunication Flat backlight for LCD ,switch and symbol in telephone and fax General use for indicators ◆ Package Dimensions: 3.2 6.10 1.50max 3.9 CATHODE ANODE 1.15 +0.1 -0.2 1.50± 0.5 2.54 Note： 1.All dimensions in mm tolerance is ±0.2mm unless otherwise noted. 2. An epoxy meniscus may extend about 1.5mm down the leads. 3.Burr around bottom of epoxy may be 0.5mm max. Prepared date：Oct. 2010 www.ledz.com Rev.：1 Page 2 of 8 Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED ◆ Absolute Maximum Rating （Ta=25℃） Parameter Symbol Max. Unit Power Dissipation PM 100 Mw Pulse Forward Current IFP 100 mA DC Forward Current IF 30 mA Reverse Voltage VR 5 V Topr -30℃～85℃ ℃ Tstg -40℃～100℃ * IFP condition: pulse width ≤0.1ms ,duty cycle ≤1/10 ℃ Operating Temperature Range Storage Temperature Range ◆ Electrical Optical Characteristics（Ta=25℃） Parameter Test Symbol Min Typ. Max. Unit IV 1700 -- 2880 mcd IF =20mA Dominant wavelength λd 520 -- 530 nm IF =20mA Forward Voltage VF 3.0 -- 3.6 V IF =20mA Reverse Current IR -- -- 10 uA VR=5V Viewing Angle 2θ1/2 -- 105/55 -- Deg. IF =20mA Luminous Intensity Condition ◆ Ranks Combination (IF = 20mA) Rank WD(nm) 520-522.5 522.5-525 525-527.5 1700-2000 2000-2400 2400-2880 527.5-530 Rank IV Rank VF(v) Notes: 3.0-3.6 1.Tolerance of Luminous Intensity±15%. 2.Tolerance of Dominant wavelength ±1nm. 3.Tolerance of Forward Voltage±0.05V. 4.Optical characteristic is measured by HB’s equipment. Prepared date：Oct. 2010 www.ledz.com Rev.：1 Page 3 of 8 Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED ◆ Soldering Conditions (Maximum allowable soldering conditions) lead-free solder fixed form mode Hand soldering DIP soldering 1. Soldering time : 3 sec MAX. 2. Distance : 3 mm MIN (from solder joint to case) 1. Preheat temp : 100 °C MAX , 60 sec MAX. 2. Bath temp : 265 °C MAX. 3. Bath time : 3 sec MAX. 4. Distance : 3 mm MIN (From solder joint to case) 5. decrease temperature externally and compulsorily after dip soldering) Prepared date：Oct. 2010 www.ledz.com Rev.：1 Page 4 of 8 Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED ◆ Typical Electro-Optical Characteristics Curves： If (mA) Iv 100 5.0 80 4.0 60 3.0 40 2.0 20 1.0 1.6 1.8 2.0 2.2 2.4 If (m A) 0.0 Vf (v) 0 0 2.6 20 40 60 80 100 Fig.2 R elative Lum inous Intensity vs. Forw ard C urrent Fig.1 Forward Current vs. Forward Voltage Half Wide= △ 35nm Iv Domi WL=525nm Iv 1.0 2.0 0.8 1.0 0.6 0.5 0.4 0.2 0.2 WL(nm) 0.0 400 450 500 550 600 0.1 Ta (℃ ) -30 -20 650 -10 0 10 20 30 40 50 60 70 Fig.4 Relative Luminous Intensity vs.Ambient Temperature Fig.3 Relative Luminous Intensity vs. Wavelength Y-Y If (m A) X-X Y-Y 50 IV X-X 100% 40 30 50% 20 10 Ta ( ℃ ) 0 0% 90° 0 20 40 60 80 Fig.5 M axim um Forw ard Current vs.Am bient Tem perature Prepared date：Oct. 2010 60° 30° 0° 30° 60° 90° 100 www.ledz.com Fig.6 Relative Luminous Intensity vs. Radiation Angle Rev.：1 Page 5 of 8 Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED ◆ Reliability (1)Test Items and Conditions Test Item Standard Test Conditions Test Method Note Reflow Soldering JEITA ED-4701 Tsld=260℃，3 sec 300 301 (pre treatment 30℃,70%,168hrs) High Temperature Storage Low Temperature Storage Number of Damaged 2 time 0/100 JEITA ED-4701 TA=100℃ 200 201 1000 Hrs 0/100 JEITA ED-4701 TA=-40℃ 200 202 1000 Hrs 0/100 1000 Hrs 0/100 JEITA ED-4701 100 103 Temperature Humidity Storage TA=60℃， RH=90%RH Thermal Shock Test JEITA ED-4701 -40℃ ~ 100℃ 300 307 15min 15 min 100 Cycles 0/100 Temperature Cycling Test JEITA ED-4701 -40℃~25℃~100℃~25℃ 100 105 30min 5min 30min 5min 100 Cycles 0/100 TA=25℃ 1000 Hrs 0/100 Operating Life Test IF=20mA (2)Criteria of judging the damage Item Symbol Test Conditions Forward Voltage VF Luminous Intensity Criteria for Judgment Min. Max. IF =20 mA --- Initial Data ×1.1 IV IF =20 mA Initial Data × 0.8 --- Reverse Current IR VR = 5V --- ≦2μA Wave length λD/λP IF=Test Current / Initial Data±2nm Appearance / View check Prepared date：Oct. 2010 www.ledz.com No mechanical damage Rev.：1 Page 6 of 8 Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED ◆ Cautions 1、Package When moisture is absorbed into the package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. So the moisture proof package is used to keep moisture to a minimum in the package. 2、Storage •Before opening the package a. Avoid the absorption of moisture, we recommended to store the LEDs in a dry box(or desiccator) with a desiccant . Otherwise, store them in the following environment: Temperature : 5℃~30℃,Humidity : 60%max. b. The products should be used in 3 months. It is recommended that the LEDs be used as soon as possible. •After opening the package a. Soldering should be done right after opening the package(within 24Hrs). b. Keeping of a fraction -sealing -Temperature : 5 ~ 30℃,Humidity : less than 30% c. If the package has been opened more than 1week or the color of desiccant changes, Components should be dried for 10-12hr at 60±5℃ 3、Lead Forming •When the lead forming is required before soldering , care must be taken to avoid any bending and mechanical stress. The stress to the base may damage the LEDs. •When mounting the LEDs onto a PCB, the holes on the circuit board should be exactly aligned with the leads of the LEDs. •It is recommended that tooling made to precisely form and cut the leads to length rather than rely on hand operating. 4、The LED electrode sections are comprised of a gold plated. The gold surface may be affected by environments which contain corrosive gases and so on. Please avoid conditions which may cause the LED to corrode or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. 5、Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. 6、Static Electricity 6.1、These products are sensitive to static electricity charge, and users are required to handle with care. Particularly, if an current and or voltage which exceeds the Absolute Maximum Rating of Products is applied, the overflow in energy may cause damage to, or possibly result in electrical destruction of, the Products. The customer is requested to take adequate countermeasures against static electricity charge and surge when handling Products. 6.2、Proper grounding of Products , use of conductive mat, conductive working uniform and shoes, and conductive containers are effective against static electricity and surge. Prepared date：Oct. 2010 www.ledz.com Rev.：1 Page 7 of 8 Hebei I.T. (Shanghai) Co., Ltd. Technical Data Sheet Lamp View LED 6.3、Ground low-resistance areas where the product contacts, such as metal surfaces of the work platform, with a conductive mat (surface resistance 106-108 Ω ). 6.4、A tip of soldering iron is requested to be grounded. An ionizer should also be installed where risk of static generation is high. 7、Circuit Protection Below the zener reference voltage VZ, all the current flows through LED and as the voltage rises to VZ, the zener diode “breakdown”. If the voltage tries to rise above VZ current flows through the zener branch to keep the voltage at exactly VZ. When the LED is connected using serial circuit, if either piece of LED is no light up but current can not flow through causing others to light down. In new design, the LED is parallel with zener diode, if either piece of LED is no light up but current can flow through causing others to light up. ◆ Notes: 1、Above specification may be changed without notice. We will reserve authority on material change for above specification. 2、When using this product, please observe the absolute maximum ratings and the instructions for the specification sheets. We assume no responsibility for any damage resulting from use of the product which does not comply with the instructions included in the specification sheets. Prepared date：Oct. 2010 www.ledz.com Rev.：1 Page 8 of 8