Datasheet

5XRGB-F2-S
Features:
◆ CMOS Technology
◆ Designed for bonding with LED chip
◆ Blinking Frequency: 34s/Cycle (Vdd=4.0V)
◆ Frequency tolerance : ±20%
◆ With both sink and source output drivers
Package Dimensions:
Part No.
5XRGB-F2-S
Chip Material
Lens Color
Source Color
AlGaInP
Water Clear
Water Clear
Water Clea
Red
InGaN
InGaN
Green
Blue
Notes:
1.All dimensions are in millimeters (inches).
2.Tolerance is ±0.25mm (.010”)unless otherwise noted.
3.Protruded resin under flange is 1.5mm(.059”)max.
4.Lead spacing is measured where the leads emerge from the package.
5.Specifications are subject to change without notice.
Part No.
5XRGB-F2-S
Spec No.
S/N-050909225
Page
1 of 3
Version: 1.0
5XRGB-F2-S
Absolute Maximum Ratings at Ta=25℃
Light color:Red、Green、 Blue
Color
z
Reverse current:100 μA
z
Peak current(duty=0.1,1KHz):100 mA
z
Operating/Storage temperature range:-30℃~ +85℃
z
Derating linear from 25℃:0.4 mA/℃
z Lead soldering temperature range:260℃ for 5 second
Electrical Optical Characteristics at Ta=25℃
RED COLOR:
Parameter
Test
Condition
IF=20 mA
Symbol
Min
Typ.
Max Unit
Forward voltage
VF
™
2.00
2.25
Luminous intensity
IV
2000
4000 mcd
Peak emission wavelength
λp
625
640
nm
™
Half intensity angle
△Θ
™
30
40
deg
™
Symbol
Min
Typ.
Forward voltage
VF
™
3.5
Luminous intensity
IV
6000
V
IF=20 mA
GREEN COLOR:
Parameter
Max Unit
4
V
9000 mcd
Test
Condition
IF=20 mA
IF=20 mA
520
530
nm
™
™
30
40
deg
™
Symbol
Min
Typ.
Forward voltage
VF
™
3.5
Luminous intensity
IV
2000
4000 mcd
Peak emission wavelength
λp
460
475
nm
™
Half intensity angle
△Θ
™
30
40
deg
™
Symbol
VDD
Min
3.5
Typ.
Max Unit
4.5
V
Peak emission wavelength
λp
Half intensity angle
△Θ
BLUE COLOR:
Parameter
Test
Condition
IF=20 mA
Max Unit
4
V
IF=20 mA
Direct Current Characteristics
Parameter
Operating voltage
Remarks
™
Driver Current
Iol
50
mA
@VDS=1.2V
Power Consumption
Po
225
mW
VDD=4.5V
Ftet
3.4
Hz
External±30%
Flash Frequency
™
*All specs and applications shown above subject to change without prior notice.
(以上电路及规格仅供参考,本公司可进行修正)
Part No.
5XRGB-F2-S
Spec No.
S/N-050909225
Page
2 of 3
Version: 1.0
Application diagram and Dimensions
Application Diagram
Dimensions
Note:
Unit:mm
Output Sketch Map
*All specs and applications shown above subject to change without prior notice.
(以上电路及规格仅供参考,本公司可进行修正)
Notes:
1. Luminous intensity is measured with a light sensor and filter combination that approximates
the CIE eye-response curve.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. The dominant wavelength (λP) is derived from the CIE chromaticity diagram and represents
the single wavelength which defines the color of the device.
Part No.
5XRGB-F2-S
Spec No.
S/N-050909225
Page
3 of 3
Version: 1.0