Catalogue

Digital Output Type 3-axis Acceleration Sensor
HAAM-385
■ Features
・12-bit digital acceleration signal output
・Serial Interface available (I2C or SPI)
・Low Voltage Drive (2.4V~), Interface block can be driven by as low as 1.7V
・Low Power Consumption ・Standby mode : 2µA Max
・Normal mode : 350µA Max. (at 200Hz)
・Various output interrupt signals by preset threshold (Wakeup, Shock detection ,Drop detection)
・Rated Acceleration(±2G, ±4G, ±8G) and Data rate can be set.
■ Additional functions
Item
Function
This is a function to change data rate(DR) by register setting
Data rate change
Settable data rate(400, 200, 100, 50, 20.4 Hz)
If detected acceleration change is more than threshold, interrupt signal will
be generated. Data rate can be changed after interrupt signal generated.
Wake-Up output
Shock detection output
Drop detection output
Data Ready (DRDY) output
If acceleration of any selected axis is more than threshold, interrupt signal will
be generated
If acceleration of all selected axis go under threshold, interrupt signal
will be generated.
This outputs signal to indicate register updating of acceleration data
was completed.
■ Outline dimension
Unit:mm
■ Block Diagram
HAAM-385
VDD
Sensor
OSC
VREF
ADC
Digital
Filter
LCA
X
Y
MUX
AMP
INT1
Z
INT2
Control
Logic
OTP
GND
I/F
(I2C, SPI)
IFS
2011.10.1(rev.2)
RESET
*1
CS
SPC/SCL
SDI/SDA
HOKURIKU
VDD_IO
*2
SDO/ADDR
*3
*Details are subject to change without notice.
1
Digital Output Type 3-axis Acceleration Sensor
HAAM-385
■ Terminal Assignment & Functions
No
Terminal
Function
1
SDO/ADDR
When SPI(4-wire) selected: Serial data output terminal
When I2C selected: slave address LSB setting (7bit)
2
INT2
Interrupt signal output 2
3
INT1
Interrupt signal output 1
4
VDD_IO
Power supply input to drive serial interface. If voltage of host side connecting to HAAM-385 is less than +2.4V,
communication is possible by supplying power to VDD_IO terminal.
Where, please use by keeping VDD (+2.4~+3.6V) ≧ VDD_IO (1.7V~VDD).
5
GND
Power supply ground
6
Reserved
Connect GND terminal
7
LCA
Connect capacitor to stabilize internal reference voltage
Please connect 0.1μF capacitor between LCA and GND.
8
VDD
Power input to drive sensor
9
Reserved
Connect GND terminal
10
IFS
I2C/SPI selection terminal (Lo:SPI, Hi:I2C)
11
RESET
Reset Signal Input (Active low)
12
CS
SPI Chip Selection Input .Slave SPI chip selection line. Active low.
13
SPC/SCL
14
SDI/SDA
When SPI(4-wire) selected: Serial Clock Input.
When I2C selected: Serial Clock Input/Output.
When SPI(4-wire) selected: Serial Data Input.
When I2C selected: Serial Data Input/Output.
■ Standard Specification
Rating
Item
Min.
Typ.
Max.
nit
Remark
Operating Condition
Temperature
Range
Power Supply
Storage Temperature Range
-40
85
℃
Operating Temperature Range
-25
85
℃
Operating Voltage Range
2.4
3.6
V
Interface Voltage Range
1.7
VDD
V
Current Consumption
400Hz
560
µA
200Hz
282
µA
100Hz
142
µA
50Hz
72
µA
20Hz
30
µA
4Hz
7.5
OSR=128, TBD
Able to change by register setting
µA
Standby Current
2
µA
Turn On Time
5
ms
Shock Durability
VDD
VDD_IO
5000
When standby mode selected
Standby →Compentation of first measure
G
Electrical Characteristics
Rated Acceleration
Output Resolution
±2G
±4G
±8G
Data Rate
±2、±4、±8
0.98
G
mg/LSB
1024
LSB/G
1.95
mg/LSB
512
LSB/G
12bit output
When normal mode selected
3.9
mg/LSB
256
LSB/G
400, 200, 100, 50, 20, 4
Hz
OSR=128, TBD
Able to change by register setting
400
kHz
400pF
1
MHz
100pF
5
MHz
40pF
Serial Interface Specification
I2C Interface Speed
SPI Interface Speed
2011.10.1(rev.2)
HOKURIKU
*Details are subject to change without notice.
2