MASTR III, P25(IP) - Harris Corporation

 ®
P25 Conventional MASTR III Station
VHF, UHF, 800 MHz
The MASTR III P25 digital Base Station
provides
 Secure digital communications for
mission-critical applications
 Capability for both conventional
Project 25 digital communications and
conventional analog communications
 Capability of delivering Internet
Protocol (IP) data and voice to a
Harris P25IP network
The MASTR III P25 provides the
flexibility to commission a base
station that will meet critical
communication needs today and
into the future. Whether users are
designing a conventional Project
25 system, a conventional VHF
system, or an IP-based P25
network, the MASTR III P25
keeps pace with their needs.
Flexible, Efficient P25 Design
The MASTR III P25 incorporates
P25 digital voice and data using
a digital signal processor modem
for maximum design flexibility.
The station can be configured for
P25 mode, and can communicate
with the user’s current analog
dispatch network through a 4wire audio port. The P25 digital
voice is translated through an onboard voice encoder/decoder in
the station to allow immediate
access to P25 communications
through the user’s existing
network.
Public Safety and Professional Communications | www.pspc.harris.com
221 Jefferson Ridge Parkway | Lynchburg, VA USA 24501 | 1-800-368-3277 (+1-434-455-6403)
Harris, assuredcommunications, and MASTR are registered trademarks of Harris Corporation.
Copyright  2012 Harris Corporation. All rights reserved.
Printed in U.S.A. 11/12 ECR-7342J
The MASTR III P25 can also
be configured for normal conventional analog operation at sites
where P25 currently is not in use.
P25IP Network
As network needs expand, the
MASTR III P25 is ready to grow
to meet the communication
requirements of the 21st century.
The MASTR III P25 and a
SitePro Controller enable IP
voice and data packets to be sent
over a Harris P25IP network and
be received at the base station.
This setup enables all of the
advantages of IP:


Seamless integration of offthe-shelf IP data applications.
Easy interconnection of
peripherals and ancillary
equipment such as mobile
data terminals, printers,
scanners, and video devices
for user organizations.


Economical routing and
backhaul of network data.
Redundancy benefit of
distributed IP architecture,
one of the key requirements
for most public safety users.
Programmable Flexibility
PC programmable options
provide flexibility, simplified
setup, and easy field upgrades.
The fully synthesized design of
the MASTR III P25 base station
allows the user to make
frequency changes quickly,
easily, and affordably.
The modular design of the
base station makes maintenance
and servicing simple and fast.
Technical specifications are subject to change without notice. Product sales are subject to applicable U.S. export control laws.
Conventional
Options and Accessories
General Specifications
Conventional
Tone and DC Remote Controlled Stations
Programmable Options
Transmit Frequencies
Receive Frequencies
Channel Guard Digital and Tone
Channel Guard Disable
Repeater Disable
Intercom Function
DTMF Decode
Morse Code ID
Squelch Tail Elimination (STE)
Carrier Control Timer
Station Control
DC Control
Tone Control
Repeater
DC/Repeat
Tone/Repeat
4-Wire Audio
Scan
Additional Options
Service Microphone
Antenna Multicoupler
230V Power Supply
Duplexer
Antenna Relay
Combiner
Isolator
Squelch-Operated Relay
Remote Controllers
Battery Standby
Battery Charger
Gel Cell Battery
Switchable Channel Spacing
Audio (Line to Transmitter)
Line Terminating Impedance:
Line Level (Adjustable):
Frequency Response:
Tone Control
Function Tones:
Secur-it Tone and Transmit
Tone:
Transmitted 2175 Hz Tone
Level:
Permissible Control Line Loss
@ 2175 Hz:
Audio (Receiver to Line)
Audio Amplifier Input
Impedance:
Input Level:
Output Impedance to Line:
Output Level to Line Voice
(1 kHz ref):
Tone (1 kHz ref):
Frequency Response:
Hum and Noise, Noise Squelch:
Tone Squelch:
DC Control Control Currents:
Line Loop Resistance
(maximum):
Power Output
(Adjustable)
(W)
10-110
10-110
10-110
10-100
10-100
10-100
FCC Type
Acceptance
Number
OWDTR-0048-E
OWDTR-0050-E
NA
OWDTR-0038-E
OWDTR-0039-E
OWDTR-0036-E
INDOOR CABINET (Floor Mount)
69 inches
83 inches
CABINET
Size [in. (cm)]
Height
Width
Depth
600 
-20 to +7 dBm
±3 dB @ 300-3000 Hz
69.1 (175)
23.1 (59)
21.0 (53)
Weight (min) [(lb (kg)]
Continuous Duty
Packed, Domestic Shipping
650, 750, 850, and 950 for P25 only
1050, 1150, 1250, 1350, 1450, 1550,
1650, 1750, 1850, 1950, and 2050 Hz
576 (261)
606 (275)
Service Speaker:
1W @ 8
Service Microphone:
Transistorized Dynamic
Duty Cycle (EIA) Continuous:
Ambient Temperature (or full spec
performance per EIA):
Transmit/Receive - 100%
Humidity (EIA):
Input Power Source:
Optional Input Power Source:
Standby Battery Source:
Antenna Connections:
Length of AC Power Cable:
Metering:
Altitude:
693 (315)
729 (331)
Number of Rack Units
33
41
Max. Units w/Power Supply
4
5
NOTE: One rack unit equals 1.75 inches. Stations occupy 6 rack units
of cabinet space.
Operable:
Shippable:
-22 to +140oF (-30 to +60oC)*
90% @ 122oF (50oC)
120 VAC (±20%), 47-63 Hz
230 VAC (±15%), 47-63 Hz
26.4 VDC, 50 AH (min.)
Type N
10 ft (3048 mm)
Provided through Handset or TQ0619 Software
Up to 15,000 ft (4,570 m)
Up to 50,000 ft (15,250 m)
*Standard network equipment for P25IP and EDACS IP configurations (0-40oC). Expanded
temperature range equipment is available on request.
20 dB Below Voice
Source Power Drain
VHF Analog
Frequency Range (MHz)
30 dB
AC Input Power
10 K
1 V RMS (for 5 kHz Deviation)
600 
+7 dBm (Adjustable)
+7 dBm (Reference 7 dBm)
+1 and -3 dB @ 300-3000 Hz
-55 dB (Reference 7 dBm)
-30 dB (Reference 7 dBm)
-2.5, ±6, and ±11 mA
11 K (Includes 3K Termination)
DC Input Power (A)
Tx (full/half) Power
Rx Power
Tx (full/half) Power
Rx Power
VDC
13.8
13.8
26.4
26.4
VHF P25 Digital
UHF Analog
UHF P25 Digital
800 MHz Analog
800 MHz P25
Digital
851-870 TX,
806-825 RX
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
851-870 TX,
806-825 RX
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
136-174
136-174
380-512
380-512
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
Transmitter (As applicable, analog specifications measured per TIA/EIA-603 Procedure and P25 digital per TIA-102.CAAA-A)
VHF Analog
VHF P25 Digital
UHF Analog
UHF P25 Digital
800 MHz Analog
800 MHz P25
Digital
Frequency Range (MHz)
Rated Power Output (W)
RF Output Impedance ()
Conducted Spurious and
Harmonic Emission
Frequency Stability (ppm)
136-174
110
50
136-174
110
50
380-512
100
50
380-512
100
50
851-870
100
50
851-870
100
50
-36 dBm
±1.0
-70 dBc
±1.0
-36 dBm
±1.0
-70 dBc
±0.5 (CAAB 3.2.2)
external frequency std
-36 dBm
±1.0
-70 dBc
±0.15 external
frequency std
Modulation Deviation (kHz)
Wideband
Narrowband
0 to ±5
0 to ±2.5
NA
2.83 kHz nominal per
TIA 102 CAAB
NA
0 to ±5
0 to ±2.5
NA
2.83 kHz nominal per
TIA 102 CAAB
NA
0 to ±5
NA
NA
12.5
1.25
1.5
Tx mask
47CFR90.210d
Mod fidelity <5%
-55
12.5/25
1.25
2
Less than 3%
NA
12.5
1.25
1.5
Tx mask
47CFR90.210d
Mod fidelity <5%
-55
25, 12.5 NPSPAC
6.25
0.5
Less than 3%
NA
2.83 kHz nominal per
TIA 102 CAAB
2.83 kHz nominal per
TIA 102 CAAB
NA
25
6.25
0.5
Tx mask
47CFR90.210d
Mod fidelity <5%
NPSPAC
FM Noise (dB)
Channel Spacing (kHz)
Synthesizer Step Size (kHz)
Frequency Spread Full Spec (MHz)
Audio Distortion (@ 1 kHz)
NA
-55
12.5/25/30
1.25
2
Less than 3%
Audio Response (pre-emphasis)
NA
0 to ±4
Within +1/-3 dB of 6
Within +1/-3 dB of 6
Within +1/-3 dB of 6
dB/octave, 300 to
dB/octave, 300 to
dB/octave, 300 to
3000 Hz per EIA
3000 Hz per EIA
3000 Hz per EIA
No. of Conventional Channels
Up to 12
Up to 12
Up to 12
Up to 12
Up to 12
Up to 12
NOTE: Rated power output is measured at the transmitter power amplifier output connector per FCC Type Acceptance filing information. Any customer-required optional items such as power
measuring devices and/or duplexers will introduce loss between the transmitter output connector and the station cabinet output connector. This loss will reduce the available power at the
station connector.
Receiver (As applicable, analog specifications measured per TIA/EIA-603 Procedure and P25 digital per TIA-102.CAAA-A)
Applicable
FCC
Rules
90
90
NA
90
22, 90
90
Industry Canada
Certification
Number
3636B-0048
3636B-0050
NA
3636B-0038
3636B-0039
3636B-0036
Applicable
Industry Canada
Rules
RSS-119
RSS-119
NA
RSS-119
RSS-119
RSS-119
NTIA
Certification
Number
JF-1208074
JF-1208074
JF-1208074
NA
NA
NA
VHF Analog*
VHF P25 Digital
UHF Analog*
UHF P25 Digital
800 MHz Analog*
800 MHz P25
Digital
Frequency Range (MHz)
RF Input Impedance ()
Channel Spacing (kHz)
Synthesizer Step Size (kHz)
Sensitivity (dBm) EIA (12 dB SINAD)
136-174
50
12.5/25/30
1.25
-116 (0.35 V)
370-512
50
12.5/25
1.25
-116 (0.35 V)
-119 (0.25 V)
-119 (0.25 V)
370-512
50
12.5
1.25
-116 (5% BER) static,
-108 faded
NA
806-825
50
25, 12.5 NPSPAC
6.25
-118 (0.28 V)
Threshold Squelch (dBm)
Selectivity
12.5 kHz
25 kHz
30 kHz
Frequency Stability (ppm)
136-174
50
12.5
1.25
-116 (5% BER)
(0.35 V)
NA
806-825
50
25, 12.5 NPSPAC
6.25
-116 (5% BER) static,
-108 faded
NA
75 dB
85 dB
90 dB
±1.0
60 dB Dig ACR
NA
NA
±1.0
75 dB
85 dB
NA
±1.0
60 dB Dig ACR
NA
NA
±0.5
20 dB (NPSPAC)
85 dB
NA
±1.0
12.5: ± 1, 25: ± 2
12.5: ±1
12.5: ± 1, 25: ± 2
12.5: ±1
±2, NPSPAC: 1.6
60 dB Dig ACR
NA
NA
±0.15 (external freq.
std)
12.5: ±1
75
80
80
90
80
NA
NA
90
75
80
NA
90
80
NA
NA
90
NA
80
NA
90
80
NA
NA
90
2.0
2.0
2.0
2.0
0.5
0.5
1 @ <3% distortion
NA
1 @ <3% distortion
NA
1 @ <3% distortion
NA
Signal Displacement Bandwidth (kHz)
Intermodulation Rejection (dB)
12.5 kHz
25 kHz
30 kHz
Spurious and Image Rejection (dB)
Frequency Spread
Full Specs. (MHz)
Audio Output @ 1000 Hz, 25/30 kHz
Channel (W)
*Audio Response (de-emphasis):
for UHF
83.0 (211)
23.1 (59)
21.0 (53)
2175 Hz
Regulatory Data
Frequency
Range
(MHz)
136-154
150-174
380-400
403-450
450-512
806-870
Technical specifications are subject to change without notice. Product sales are subject to applicable U.S. export control laws.
Within +2/-8 dB of 6 dB/octave (@ Local Speaker), 300 to 3000 Hz per EIA
Within +1/-3 dB of 6 dB/octave (@ Line Output), 300 to 3000 Hz per EIA
-121 (0.18 V)
Technical specifications are subject to change without notice. Product sales are subject to applicable U.S. export control laws.
Conventional
Options and Accessories
General Specifications
Conventional
Tone and DC Remote Controlled Stations
Programmable Options
Transmit Frequencies
Receive Frequencies
Channel Guard Digital and Tone
Channel Guard Disable
Repeater Disable
Intercom Function
DTMF Decode
Morse Code ID
Squelch Tail Elimination (STE)
Carrier Control Timer
Station Control
DC Control
Tone Control
Repeater
DC/Repeat
Tone/Repeat
4-Wire Audio
Scan
Additional Options
Service Microphone
Antenna Multicoupler
230V Power Supply
Duplexer
Antenna Relay
Combiner
Isolator
Squelch-Operated Relay
Remote Controllers
Battery Standby
Battery Charger
Gel Cell Battery
Switchable Channel Spacing
Audio (Line to Transmitter)
Line Terminating Impedance:
Line Level (Adjustable):
Frequency Response:
Tone Control
Function Tones:
Secur-it Tone and Transmit
Tone:
Transmitted 2175 Hz Tone
Level:
Permissible Control Line Loss
@ 2175 Hz:
Audio (Receiver to Line)
Audio Amplifier Input
Impedance:
Input Level:
Output Impedance to Line:
Output Level to Line Voice
(1 kHz ref):
Tone (1 kHz ref):
Frequency Response:
Hum and Noise, Noise Squelch:
Tone Squelch:
DC Control Control Currents:
Line Loop Resistance
(maximum):
Power Output
(Adjustable)
(W)
10-110
10-110
10-110
10-100
10-100
10-100
FCC Type
Acceptance
Number
OWDTR-0048-E
OWDTR-0050-E
NA
OWDTR-0038-E
OWDTR-0039-E
OWDTR-0036-E
INDOOR CABINET (Floor Mount)
69 inches
83 inches
CABINET
Size [in. (cm)]
Height
Width
Depth
600 
-20 to +7 dBm
±3 dB @ 300-3000 Hz
69.1 (175)
23.1 (59)
21.0 (53)
Weight (min) [(lb (kg)]
Continuous Duty
Packed, Domestic Shipping
650, 750, 850, and 950 for P25 only
1050, 1150, 1250, 1350, 1450, 1550,
1650, 1750, 1850, 1950, and 2050 Hz
576 (261)
606 (275)
Service Speaker:
1W @ 8
Service Microphone:
Transistorized Dynamic
Duty Cycle (EIA) Continuous:
Ambient Temperature (or full spec
performance per EIA):
Transmit/Receive - 100%
Humidity (EIA):
Input Power Source:
Optional Input Power Source:
Standby Battery Source:
Antenna Connections:
Length of AC Power Cable:
Metering:
Altitude:
693 (315)
729 (331)
Number of Rack Units
33
41
Max. Units w/Power Supply
4
5
NOTE: One rack unit equals 1.75 inches. Stations occupy 6 rack units
of cabinet space.
Operable:
Shippable:
-22 to +140oF (-30 to +60oC)*
90% @ 122oF (50oC)
120 VAC (±20%), 47-63 Hz
230 VAC (±15%), 47-63 Hz
26.4 VDC, 50 AH (min.)
Type N
10 ft (3048 mm)
Provided through Handset or TQ0619 Software
Up to 15,000 ft (4,570 m)
Up to 50,000 ft (15,250 m)
*Standard network equipment for P25IP and EDACS IP configurations (0-40oC). Expanded
temperature range equipment is available on request.
20 dB Below Voice
Source Power Drain
VHF Analog
Frequency Range (MHz)
30 dB
AC Input Power
10 K
1 V RMS (for 5 kHz Deviation)
600 
+7 dBm (Adjustable)
+7 dBm (Reference 7 dBm)
+1 and -3 dB @ 300-3000 Hz
-55 dB (Reference 7 dBm)
-30 dB (Reference 7 dBm)
-2.5, ±6, and ±11 mA
11 K (Includes 3K Termination)
DC Input Power (A)
Tx (full/half) Power
Rx Power
Tx (full/half) Power
Rx Power
VDC
13.8
13.8
26.4
26.4
VHF P25 Digital
UHF Analog
UHF P25 Digital
800 MHz Analog
800 MHz P25
Digital
851-870 TX,
806-825 RX
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
851-870 TX,
806-825 RX
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
136-174
136-174
380-512
380-512
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
5A @ 120 VAC or
3A @ 230 VAC
A
2
2
12/8
0.5
Transmitter (As applicable, analog specifications measured per TIA/EIA-603 Procedure and P25 digital per TIA-102.CAAA-A)
VHF Analog
VHF P25 Digital
UHF Analog
UHF P25 Digital
800 MHz Analog
800 MHz P25
Digital
Frequency Range (MHz)
Rated Power Output (W)
RF Output Impedance ()
Conducted Spurious and
Harmonic Emission
Frequency Stability (ppm)
136-174
110
50
136-174
110
50
380-512
100
50
380-512
100
50
851-870
100
50
851-870
100
50
-36 dBm
±1.0
-70 dBc
±1.0
-36 dBm
±1.0
-70 dBc
±0.5 (CAAB 3.2.2)
external frequency std
-36 dBm
±1.0
-70 dBc
±0.15 external
frequency std
Modulation Deviation (kHz)
Wideband
Narrowband
0 to ±5
0 to ±2.5
NA
2.83 kHz nominal per
TIA 102 CAAB
NA
0 to ±5
0 to ±2.5
NA
2.83 kHz nominal per
TIA 102 CAAB
NA
0 to ±5
NA
NA
12.5
1.25
1.5
Tx mask
47CFR90.210d
Mod fidelity <5%
-55
12.5/25
1.25
2
Less than 3%
NA
12.5
1.25
1.5
Tx mask
47CFR90.210d
Mod fidelity <5%
-55
25, 12.5 NPSPAC
6.25
0.5
Less than 3%
NA
2.83 kHz nominal per
TIA 102 CAAB
2.83 kHz nominal per
TIA 102 CAAB
NA
25
6.25
0.5
Tx mask
47CFR90.210d
Mod fidelity <5%
NPSPAC
FM Noise (dB)
Channel Spacing (kHz)
Synthesizer Step Size (kHz)
Frequency Spread Full Spec (MHz)
Audio Distortion (@ 1 kHz)
NA
-55
12.5/25/30
1.25
2
Less than 3%
Audio Response (pre-emphasis)
NA
0 to ±4
Within +1/-3 dB of 6
Within +1/-3 dB of 6
Within +1/-3 dB of 6
dB/octave, 300 to
dB/octave, 300 to
dB/octave, 300 to
3000 Hz per EIA
3000 Hz per EIA
3000 Hz per EIA
No. of Conventional Channels
Up to 12
Up to 12
Up to 12
Up to 12
Up to 12
Up to 12
NOTE: Rated power output is measured at the transmitter power amplifier output connector per FCC Type Acceptance filing information. Any customer-required optional items such as power
measuring devices and/or duplexers will introduce loss between the transmitter output connector and the station cabinet output connector. This loss will reduce the available power at the
station connector.
Receiver (As applicable, analog specifications measured per TIA/EIA-603 Procedure and P25 digital per TIA-102.CAAA-A)
Applicable
FCC
Rules
90
90
NA
90
22, 90
90
Industry Canada
Certification
Number
3636B-0048
3636B-0050
NA
3636B-0038
3636B-0039
3636B-0036
Applicable
Industry Canada
Rules
RSS-119
RSS-119
NA
RSS-119
RSS-119
RSS-119
NTIA
Certification
Number
JF-1208074
JF-1208074
JF-1208074
NA
NA
NA
VHF Analog*
VHF P25 Digital
UHF Analog*
UHF P25 Digital
800 MHz Analog*
800 MHz P25
Digital
Frequency Range (MHz)
RF Input Impedance ()
Channel Spacing (kHz)
Synthesizer Step Size (kHz)
Sensitivity (dBm) EIA (12 dB SINAD)
136-174
50
12.5/25/30
1.25
-116 (0.35 V)
370-512
50
12.5/25
1.25
-116 (0.35 V)
-119 (0.25 V)
-119 (0.25 V)
370-512
50
12.5
1.25
-116 (5% BER) static,
-108 faded
NA
806-825
50
25, 12.5 NPSPAC
6.25
-118 (0.28 V)
Threshold Squelch (dBm)
Selectivity
12.5 kHz
25 kHz
30 kHz
Frequency Stability (ppm)
136-174
50
12.5
1.25
-116 (5% BER)
(0.35 V)
NA
806-825
50
25, 12.5 NPSPAC
6.25
-116 (5% BER) static,
-108 faded
NA
75 dB
85 dB
90 dB
±1.0
60 dB Dig ACR
NA
NA
±1.0
75 dB
85 dB
NA
±1.0
60 dB Dig ACR
NA
NA
±0.5
20 dB (NPSPAC)
85 dB
NA
±1.0
12.5: ± 1, 25: ± 2
12.5: ±1
12.5: ± 1, 25: ± 2
12.5: ±1
±2, NPSPAC: 1.6
60 dB Dig ACR
NA
NA
±0.15 (external freq.
std)
12.5: ±1
75
80
80
90
80
NA
NA
90
75
80
NA
90
80
NA
NA
90
NA
80
NA
90
80
NA
NA
90
2.0
2.0
2.0
2.0
0.5
0.5
1 @ <3% distortion
NA
1 @ <3% distortion
NA
1 @ <3% distortion
NA
Signal Displacement Bandwidth (kHz)
Intermodulation Rejection (dB)
12.5 kHz
25 kHz
30 kHz
Spurious and Image Rejection (dB)
Frequency Spread
Full Specs. (MHz)
Audio Output @ 1000 Hz, 25/30 kHz
Channel (W)
*Audio Response (de-emphasis):
for UHF
83.0 (211)
23.1 (59)
21.0 (53)
2175 Hz
Regulatory Data
Frequency
Range
(MHz)
136-154
150-174
380-400
403-450
450-512
806-870
Technical specifications are subject to change without notice. Product sales are subject to applicable U.S. export control laws.
Within +2/-8 dB of 6 dB/octave (@ Local Speaker), 300 to 3000 Hz per EIA
Within +1/-3 dB of 6 dB/octave (@ Line Output), 300 to 3000 Hz per EIA
-121 (0.18 V)
®
P25 Conventional MASTR III Station
VHF, UHF, 800 MHz
The MASTR III P25 digital Base Station
provides
 Secure digital communications for
mission-critical applications
 Capability for both conventional
Project 25 digital communications and
conventional analog communications
 Capability of delivering Internet
Protocol (IP) data and voice to a
Harris P25IP network
The MASTR III P25 provides the
flexibility to commission a base
station that will meet critical
communication needs today and
into the future. Whether users are
designing a conventional Project
25 system, a conventional VHF
system, or an IP-based P25
network, the MASTR III P25
keeps pace with their needs.
Flexible, Efficient P25 Design
The MASTR III P25 incorporates
P25 digital voice and data using
a digital signal processor modem
for maximum design flexibility.
The station can be configured for
P25 mode, and can communicate
with the user’s current analog
dispatch network through a 4wire audio port. The P25 digital
voice is translated through an onboard voice encoder/decoder in
the station to allow immediate
access to P25 communications
through the user’s existing
network.
Public Safety and Professional Communications | www.pspc.harris.com
221 Jefferson Ridge Parkway | Lynchburg, VA USA 24501 | 1-800-368-3277 (+1-434-455-6403)
Harris, assuredcommunications, and MASTR are registered trademarks of Harris Corporation.
Copyright  2012 Harris Corporation. All rights reserved.
Printed in U.S.A. 11/12 ECR-7342J
The MASTR III P25 can also
be configured for normal conventional analog operation at sites
where P25 currently is not in use.
P25IP Network
As network needs expand, the
MASTR III P25 is ready to grow
to meet the communication
requirements of the 21st century.
The MASTR III P25 and a
SitePro Controller enable IP
voice and data packets to be sent
over a Harris P25IP network and
be received at the base station.
This setup enables all of the
advantages of IP:


Seamless integration of offthe-shelf IP data applications.
Easy interconnection of
peripherals and ancillary
equipment such as mobile
data terminals, printers,
scanners, and video devices
for user organizations.


Economical routing and
backhaul of network data.
Redundancy benefit of
distributed IP architecture,
one of the key requirements
for most public safety users.
Programmable Flexibility
PC programmable options
provide flexibility, simplified
setup, and easy field upgrades.
The fully synthesized design of
the MASTR III P25 base station
allows the user to make
frequency changes quickly,
easily, and affordably.
The modular design of the
base station makes maintenance
and servicing simple and fast.