JGC0118 Page 1 of 5 These lamps are of the so-called 1206 size, measuring approximately 1.5 x 3.0 mm. PART NO. JGC0118 Chip Material Emitted Color AlGaInP Green Lens Color Water Clear * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 2 of 5 Absolute Maximum Ratings at Ta = 25 ˚C Parameter Symbol Rating Units Forward Current IF 25 mA Reverse Voltage VR 5 V Operating Temperature Topr -40 to +85 ˚C Storage Temperature Tstg -40 to +90 ˚C Electrostatic Discharge ESD 2000 V Power Dissipation Pd 60 mW Peak Forward Current (Duty 1/10 @ 1KHz) IFP 60 mA Soldering Temperature Tsol Reflow Soldering: 260°C for 10 sec. Hand Soldering: 350°C for 3 sec. Electronic Optical Characteristics (Ta = 25 ˚C) Parameter Symbol Min. Typ. Max. Units Luminous Intensity IV 29 39 — mcd Viewing Angle 2θ1/2 — 60 — deg Peak Wavelength λp — 575 — nm Dominant Wavelength λd — 573 — nm Spectrum Radiation Bandwidth Δλ — 20 — nm Forward Voltage VF 1.7 2.0 2.4 V Reverse Current IR — — 10 μA Condition IF = 20 mA VR = 5 V * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 3 of 5 Typical Electro-Optical Characteristics Curves: * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 4 of 5 Reel Dimensions: Carrier Tape Dimensions: * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 5 of 5 Precautions for Use 1. Over-current prevention: A series resistor must be used for protection against over-current. Since slight voltage shifts can cause large current changes and possibly damage the LED. 2. Storage: 2.1. Store the LEDs in the sealed moisture proof bag until ready to use. 2.2. The storage conditions should be below 30°C and 90% RH or less. 2.3. Unused portions of LEDs may be stored in moisture proof packages for up to 1 year if kept under 30°C and at no more than 60% RH. 2.4. If there is evidence of moisture absorption or if the LEDs have been stored for a long time, bake the LEDs at 60°C ± 5°C for 24 hours prior to using. 3. Reflow Soldering Conditions: 3.1. Pb-free solder temperature profile (see figure): 3.2. Reflow solder no more than two times and must include time interval for the board to cool. 3.3. When soldering, do not put stress on the LEDs during heating. 3.4. After soldering, do not warp the circuit board. 4. Hand Soldering: Use a low wattage soldering iron (below 25 watts) with a tip temperature no more than 350°C for 3 sec or less on one terminal. Wait at least two seconds before soldering the next terminal to avoid overheating the LED and damaging it. 5. Avoid reworking a soldered LED. It is best to simply replace it with a new part. * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902