SAW Bandpass Filter 205604B

SAW Bandpass Filter 205604B
Features
For IF bandpass filter
High attenuation
Single-ended operation
SMD Package 13.3mm × 6.5mm × 1.6mm
Package Dimension
13.30±0.2
8
7
7
1
2
3
9
10
11
1.50±0.1
205604B
12
8
6
6
ITF 03A001A
5
5
4
12
2.54±0.1
11
9
1.61±0.2
6.50±0.2
10
7.62±0.1
3
4
2
2.54±0.1
1
0.80±0.1
Package S1365
Dimensions shown are nominal in millimeters
Pin Configuration
Body : Al2O3 Ceramic
Lid : Kovar, Ni Plated
Terminations : Au plating 0.3 ~ 1.0 um,
Over a 1.27 ~ 8.89 um Ni Plating
11
Input
5
Output
6, 12
Ground
1, 2, 3, 4, 7, 8, 9, 10
Case ground
Maximum Ratings
Parameter
Unit
Minimum
Typical
Maximum
Operation Temperature Range
°C
-10
25
60
Storage Temperature Range
°C
-40
-
85
Electrostatics Sensitive Device (ESD)
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
1/8
SAW Bandpass Filter 205604B
Electrical Specification
Fc = 100MHz
Terminating source impedance
: 50Ω and matching network
Terminating load impedance
: 50Ω and matching network
Minimum
Typical
Maximum
MHz
99.925
100.000
100.075
dB
-
4.0
5.5
3dB Bandwidth
MHz
0.03
0.06
-
Absolute Delay
usec
-
10
15
dB
50
50
55
55
-
ppm/°C2
-
-0.03
-
Center Frequency at room temp.
Insertion Loss
Relative Attenuation
98.0 ~ 99.5 MHz
101.0 ~ 102.0 MHz
Temperature Coefficient of Frequency
Notes :
1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and
full 2 port calibration.
2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing
tolerances
3) All attenuation measurements are measured relative to insertion loss
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
2/8
SAW Bandpass Filter 205604B
Matching Schematic
( Actual matching values may vary due to PCB layout and parasitics )
Input
50Ω
L1
L2
C1
Output
50Ω
C2
L1=L2=330nH,
C1=C2=2pF
Marking Configuration
ITF1) 03A0012) A3)
205604B4)
1) Manufacturer name
2) Lot Number
3) Group Name ( **refer to the next page )
4) Part Number
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
3/8
SAW Bandpass Filter 205604B
Marking Example
Center Frequency Range ( MHz) at room temp.
Marking
99.925 ~ 99.935
ITF 02D073A
A
205604B
99.936 ~ 99.945
ITF 02D073B
B
205604B
99.946 ~ 99.955
ITF 02D073C
C
205604B
99.956 ~ 99.965
ITF 02D073D
D
205604B
99.966 ~ 99.975
ITF 02D073E
E
205604B
99.976 ~ 99.985
ITF 02D073F
F
205604B
99.986 ~ 99.995
ITF 02D073G
G
205604B
99.996 ~ 100.005
ITF 02D073H
H
205604B
100.006 ~ 100.015
ITF 02D073II
205604B
100.016 ~ 100.025
ITF 02D073JJ
205604B
100.026 ~ 100.035
ITF 02D073K
K
205604B
100.036 ~ 100.045
ITF 02D073L
L
205604B
100.046 ~ 100.055
ITF 02D073M
M
205604B
100.056 ~ 100.065
ITF 02D073N
N
205604B
100.066 ~ 100.075
ITF 02D073O
O
205604B
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
4/8
SAW Bandpass Filter 205604B
Typical Performance (at +25℃
℃)
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
5/8
SAW Bandpass Filter 205604B
Temperature Characteristic
2
y = -8E-06x + 0.0002x + 99.963
2
R = 0.971
99.968
99.966
99.964
Fc (MHz)
99.962
99.960
99.958
99.956
99.954
99.952
99.950
99.948
-20
-10
0
10
20
30
Temp (℃)
40
50
60
-5.75
-20
-10
0
10
20
30
Temp (℃)
40
50
60
70
-3.25
-3.5
-3.75
I.L (dB)
-4
-4.25
-4.5
-4.75
-5
-5.25
-5.5
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
70
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
6/8
SAW Bandpass Filter 205604B
Packing Specification
1. Reeling Quantity : 2000 pcs / reel
2. Taping Structure : The tape shall be wound around the reel in the direction shown below.
TOP COVER TAPE
REEL
CARRIER TAPE
Tape Specification
1. Leader part and vacant position specification
Vacant
150mm min.
Component
contained
Vacant
150mm min.
Leader part
250mm min.
END
START
Tape Running Direction
2. Tensile strength of carrier tape
4.4N/mm width
Direction of pull
Top cover tape
3. Top cover tape adhesion
0~15 degree
1) pull off angle : 0~15
2) speed : 300mm/min
3) force : 20~70g
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Carrier tape
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
7/8
SAW Bandpass Filter 205604B
Carrier Tape Dimensions [unit : mm]
A
7.00 ± 0.1
B
13.80 ± 0.1
C
13.25 ± 0.1
D
1.95 ± 0.1
E
24.00 ± 0.1
F
12.00 ± 0.1
Part Direction
Tape Running Direction
Reel Dimensions [unit : mm]
G = 2G = 24.4 mm
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
205604B
Rev. Date
2010-03-17
Rev.
NI2010-AS03
8/8