PDF

1.6 mm x 1.2 mm 4 Pads SMD Oscillator
ISM16 Series
Product Features:
Applications:
Low Jitter, Non-PLL Based Output
CMOS Output
Wide Range of Supply Voltage (+1.8V to +3.3 V)
Stand-by Function on Pin 1
RoHS Compliant
Compatible with Leadfree Processing
Fibre Channel
Server & Storage
Sonet / SDH
802.11 / Wifi
T1/E1, T3/E3
1.60±.10
Frequency
1.000000 MHz to 80.000000 MHz
Output Level
CMOS
Logic “0” = 0.4 V max
Logic “1” = Vcc – 0.4 V min
Duty Cycle
See Duty Cycle Table in Part Number Guide
Rise / Fall Time
4.5 nSec max (10% to 90% of waveform)
Output Load
15pF max
Frequency Stability
See Frequency Stability Table in Part Number Guide (Note 1)
Start-up time
2.0 mSec max with Vcc = +3.30 VDC
5.0 mSec max with Vcc = +1.80 VDC
Stand By Terminal
Function (Pin 1)
0.7 Vcc min = Output enable
0.3 Vcc max = Oscillation stop and High impedance output
Supply Voltage (Vcc)
See Input Voltage Table in Part Number Guide
(Tolerance = ±10%)
Current
During Standby
During Operation
1.20±.10
Marking
0.70
max
0.40
0.30
1
2
4
3
0.40
0.50
0.50
0.50
1.10
0.80
10 µA max
2.5 typ., 3.5 mA max (1.8 V, 15 pF load @ 50.000MHz)
3.5 typ., 5.0 mA max (1.8 V, 15 pF load @ 80.000MHz)
0.50
0.60
4.2 typ., 6.0 mA max (3.3 V, 15 pF load @ 50.000MHz)
6.0 typ., 8.5 mA max (3.3 V, 15 pF load @ 80.000MHz)
Aging
Temperature Range
Operating
Storage
Random Jitter (RJ)
Total Jitter (TJ)
Phase Jitter
Suggested
Land Patterns
± 3.0 ppm max @ +25ºC First Year
Pin 1
Pin 2
Pin 3
Pin 4
See Operating Temperature Table in Part Number Guide
-40ºC to +105ºC
2.9 pSec typ
40.0 pSec typ
TJ = n x RJ were n ≈ 14.1, BER = 10-12
1.0 pSec max
Offset frequency = 12 kHz to 5.000MHZ
Pin Connections
Stand-by
Ground
Output
Supply Voltage (Vcc)
Dimensions: mm
Notes:
1. Includes room temperature tolerance and stability over operating temperature.
2. A 0.01 µF bypass capacitor is recommended between Vcc (Pin 4) and GND (Pin 2) to minimize power supply noise.
Part Number Guide:
Input
Package
Voltage
1 = +1.8V
3 = +3.3V
ISM16
6 = +2.5V
1
2
3
5
=
=
=
=
Operating
Temperature
0ºC to +70ºC
-40ºC to +85ºC
-20ºC to +70ºC
-30ºC to +85ºC
Duty Cycle
(Symmetry)
5 = 45/55 max
6 = 40/60 max
Output
3 = 15 pF
Sample Part Number: ISM16-3153A-20.0000
Stability
Frequency
(in ppm)
A = ±25*
B = ±50
C = ±100
-20.0000
F = ±20*
*Not available for all temperature ranges
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 06/02/15_A
Page 1 of 2
1.6 mm x 1.2 mm 4 Pads SMD Oscillator
ISM16 Series
Pb Free Solder Reflow Profile:
Typical Application:
Vcc
C1
0.01
uF
Output
3
4
Oscillator
1
Stand by
2
Units are backward compatible with 240ºC reflow process.
Package Information:
MSL = N.A. (package does not contain plastic; storage life is unlimited under normal room conditions).
Termination = e4 (Au over Ni over W base metallization).
Tape and Reel Information:
Quantity per
Reel
A
B
C
8.0 ±0.2
4.0 ±0.1
3.5 ±0.05
D
E
F
9.0 ±0.3
60 / 80
180 / 250
3000
Environmental Specifications:
Thermal Shock
Moisture Resistance
Mechanical Shock
Mechanical Vibration
Resistance to Soldering Heat
Hazardous Substance
Solderability
Terminal Strength
Gross Leak
Fine Leak
Solvent Resistance
MIL-STD-883, Method 1011, Condition A
MIL-STD-883, Method 1004
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 2007, Condition A
J-STD-020C, Table 5-2 Pb-free devices (except 2 cycles max)
Pb-Free / RoHS / Green Compliant
JESD22-B102-D Method 2 (Preconditioning E)
MIL-STD-883, Method 2004, Test Condition D
MIL-STD-883, Method 1014, Condition C
MIL-STD-883, Method 1014, Condition A2, R1=2x10-8 atm cc/s
MIL-STD-202, Method 215
Marking:
Line 1: I - Date Code (yww)
Line 2: Frequency
PROPRIETARY AND CONFIDENTIAL
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION, AND SUCH INFORMATION MAY NOT BE DISCLOSED TO OTHERS FOR ANY
PURPOSE NOR USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM ILSI America.
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 06/02/15_A
Page 2 of 2