3.2 mm x 5.0 mm Ceramic Package SMD Oscillator ISM82 Series Product Features: Wide Temperature Range (-55º to +125ºC) Frequency Stability option ±50 ppm over the full operating temperature range. Low Phase Noise RoHS Compliant 5.00±.20 Frequency 1.000 MHz to 125.000 MHz Output Level CMOS Logic ‘0’ = 10% of Vcc max Logic ‘1’ = 90% of Vcc min Duty Cycle Specify 50% ±10% or ±5% See Table in Part Number Guide Rise / Fall Time 5 nS Max. for 10% to 90% of waveform IYWW FREQ 1.30 max 15 pF Output Load 2.54 Frequency Stability See Frequency Stability Table (Includes room temperature tolerance and stability over operating temperature) Aging (Initial First Year) ±3 ppm max Start-up Time 5 mS Max. Supply Voltage See Input Voltage Table, tolerance ±5 % Current 50 mA Max. Operating -55 C to +125 C Storage -55 C to +125 C Phase Jitter: (12kHz – 20MHz) Tri-State (Pin 1) Function Enable / Disable Time Current, Standby Mode Part Number Guide Input Package Voltage ISM82 3.20±.20 1 = 1 .8 V 2 = 2.7 V 3 = 3.3 V 6 = 2.5 V 7 = 3.0 V 1.20 4 3 1 2 1.20 2.54 2.20 1.20 1.40 Recommended Land Pattern 1 pS RMS max Pin Connection Enable / Disable or NC Pin 2 Ground Output Pin 3 Vcc Pin 4 Standby 100 nS Max. N.C. or ≥ 70% Vcc = Enable. ≤ 30% Vcc = Disable 20 µA Sample Part Number: Operating Temperature Symmetry (Duty Cycle) Output 7 = -55ºc to +125ºc 5 = 45 / 55 max 6 = 40 / 60 max 3 = 15pF 6 = 30pF * Pin 1 ISM82-3756BH-20.000 Stability (in Enable / Frequency ppm) Disable B = ±50 ppm C= ±100 ppm H = Enable O = N/C 20.000 *Oscillator may not meet 5% symmetry over temperature range with 30 pF load. NOTE: A 0.01 µF bypass capacitor is recommended between Vcc (pin 4) and GND (pin 2) to minimize power supply noise. ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev: 10/20/14_A3 Page 1 of 2 3.2 mm x 5.0 mm Ceramic Package SMD Oscillator Pb Free Solder Reflow Profile: ISM82 Series Typical Application: *Units are backward compatible with 240º C reflow processes Package Information: MSL = N.A. (Package does not contain plastic; storage life is unlimited under normal room conditions.) Termination = e4 (Au over Ni over W base metallization). Tape and Reel Information: Quantity per Reel A B C D E F 1000 16 +/-.3 8 +/-.2 7.5 +/-.2 17.5 +/-1 50 / 60 / 80 180 / 250 Environmental Specifications: Thermal Shock Moisture Resistance Mechanical Shock Mechanical Vibration Resistance to Soldering Heat Hazardous Substance Solderability Terminal Strength Gross Leak Fine Leak Solvent Resistance MIL-STD-883, Method 1011, Condition A MIL-STD-883, Method 1004 MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2007, Condition A J-STD-020C, Table 5-2 Pb-free devices (except 2 cycles max) Pb-Free / RoHS / Green Compliant JESD22-B102-D Method 2 (Preconditioning E) MIL-STD-883, Method 2004, Test Condition D MIL-STD-883, Method 1014, Condition C MIL-STD-883, Method 1014, Condition A2, R1=2x10-8 atm cc/s MIL-STD-202, Method 215 Marking: Line 1: ILSI and Date Code (YWW) Line 2: Frequency Proprietary and Confidential This document contains proprietary information, and such information may not be disclosed to others for any purpose nor used for manufacturing purpose without the written permission o ILSI America. ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev: 10/20/14_A3 Page 2 of 2