OPTOWAY TRML

Optoway
TRML-9100FG
1
***********************************************************************************************************************************************************************
TRML-9100FG / TRML-9100FAG
3.3V / 850 nm / 2.5 Gbps RoHS Compliant SFF LC MULTI-MODE TRANSCEIVER
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Duplex LC Multi-Mode Transceiver
l Compliant with Fibre Channel FC-PH-2 for
200-M5-SN-1 and 200-M6-SN-1
l Compliant with IEEE 802.3z 1000BASE-SX
l Link Distance at 2.125 Gbd
150 m links with 62.5/125 µm MMF Cables
300 m links with 50/125 µm MMF Cables
l Link Distance at 1.026 Gbd
300 m links with 62.5/125 µm MMF Cables
500 m links with 50/125 µm MMF Cables
l Small Form Factor, RJ-45 size, 2X5 pin Package
l AC/AC Coupled Signal Input / Output
l LVTTL Transmitter Disable Input
l LVTTL Signal Detection Output
l Single +3.3 V Power Supply
l RoHS Compliant
l 0 to 70oC Operating: TRML-9100FG
l -20 to 85oC Operating: TRML-9100FAG
l Wave Solderable and Aqueous Washable
l Class 1 Laser International Safety Standard IEC-60825
Compliant
The TRML-9100FG series multi-mode transceivers is small
form factor, low power, high performance module for
bi-directional serial optical data communications such as
Fibre Channel FC-PH-2 for 200-M5-SN-1 and
200-M6-SN-1 and Gigabit Ethernet IEEE 802.3z
1000BASE-SX. This module is designed for multi-mode
fiber and operates at a nominal wavelength of 850 nm. The
transmitter section uses a multiple quantum well 850 nm
VCSEL and is a class 1 laser compliant according to
International Safety Standard IEC-60825. The receiver
section uses an integrated GaAs detector preamplifier (IDP)
mounted in an optical header and a limiting post-amplifier
IC. A PECL logic interface simplifies interface to external
circuitry.
LASER SAFETY
This multi-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
APPLICATIONS
l SONET/SDH Equipment Interconnect
l Gigabit Ethernet 1.25 Gb/s Links
ORDER INFORMATION
P/No.
TRML-9100FG
TRML-9100FAG
Bit Rate
(Gb/s)
FC-PI
2.125/1.063
2.125/1.063
200/100
200/100
Distance Wavelength
(m)
(nm)
Package
Temp.
(oC)
150/300*
150/300*
2X5 LC
2X5 LC
0 to 70
-20 to 85
850
850
TX Power RX Sens.
RoHS
(dBm)
(dBm) Compliant
-4 to -9
-15
Yes
-4 to -9
-15
Yes
Note: 150 m links with 62.5/125 µm MMF Cables and 300 m links with 62.5/125 µm MMF Cables.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Symbol
Tstg
Topr
Soldering Temperature
Power Supply Voltage
Input Voltage
--Vcc
---
Min
-40
0
-20
0
GND
Max
85
70
85
260
4.5
Vcc
Units
o
C
o
C
Typ
3.3
Max
3.47
70
85
o
C
V
V
Notes
TRML-9100FG
TRML-9100FAG
10 seconds on leads only
Recommended Operating Conditions
Parameter
Power Supply Voltage
Operating Temperature
Symbol
Vcc
Topr
Data Rate
Power Supply Current
Icc
Min
3.13
0
-20
1
2.125
180
240
Units / Notes
V
o
C / TRML-9100FG
o
C / TRML-9100FAG
Gb/s
mA
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
TRML-9100FG
2
***********************************************************************************************************************************************************************
Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V)
Parameter
Optical
Optical Transmit Power
Output Center Wavelength
Output Spectrum Width
Optical Modulation Amplitude
Extinction Ratio
Output Eye
Optical Rise Time
Optical Fall Time
Relative Intensity Noise
Electrical
Data Input Current – Low
Data Input Current – High
Differential Input Voltage
Data Input Voltage – Low
Data Input Voltage -- High
Disable Input Voltage -- Low
Disable Input Voltage -- High
Shut Off Time for TxDis
Symbol
Min
Typ
Max
Units
Notes
Po
-9
830
λ
--∆λ
OMA
196
ER
Compliant with IEEE 802.3z
tr
tf
RIN
--850
---
-4
860
0.85
1
9
---
dBm
nm
nm
µW
dB
150
150
-117
ps
ps
dB/Hz
IIL
IIH
VIH - V IL
VIL - V CC
VIH - V CC
VTDIS,L
VTDIS,H
tDIS
-350
350
300
-2.0
-1.1
0
Vcc – 1.3
-1.58
-0.74
0.5
Vcc
1
µA
µA
mV
V
V
V
V
ms
RMS (σ)
2
20% to 80%
20% to 80%
3
3
TX Output Enabled
TX Ouput Disabled
Notes: 1. Output power is power coupled into a 62.5/125 µm MM fiber.
2. An OMA of 196 µW is approximately equal to an average power of -9 dBm assuming an Extinction Ratio of 9 dB.
3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs.
Receiver Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3.47V)
Parameter
Optical
Sensitivity
Maximum Input Power
Signal Detect -- Asserted
Signal Detect -- Deasserted
Signal detect -- Hysteresis
Wavelength of Operation
Electrical
Data Output Voltage – Low
Data Output Voltage – High
Signal Detect Output Voltage -- Low
Signal Detect Output Voltage -- High
Symbol
Min
Typ
Max
Units
Notes
--Pin
Pa
Pd
--0
---31
1.0
1100
---
-15
---15
---
dBm
dBm
dBm
dBm
dB
nm
1
VOL - VCC
VOH - VCC
VOL
VOH
-2.0
-1.1
---------
1600
-1.58
-0.74
0.5
2.0
V
V
V
V
Transition: low to high
Transition: high to low
2
2
Notes: 1. Minimum sensitivity and saturation levels at BER=1E-12 for a 27-1 PRBS.
2. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
TRML-9100FG
3
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
PIN
1
2
3
4
5
6
7
8
Symbol
VEEr
VCC r
SD
RD−
RD+
VCC t
VEEt
TDis
9
10
MS
TD+
TDMS
Notes
Directly connect this pin to the receiver ground plane
+3.3V dc power for the receiver section
Active high on this indicates a received optical signal.
Receiver Dataout Bar. See recommended circuit schematic
Receiver Dataout. See recommended circuit schematic
+3.3V dc power for the transmitter section
Directly connect this plan to the transmitter ground plane
Transmitter Disable. Connect this pin to +3.3V TTL logic “1” to disable module
To enable module connect to TTL logic low “0”
Transmitter Data In. See recommended circuit schematic
Transmitter Data In Bar. See recommended circuit schematic
Mounting Studs. Connect to Chassis Ground
RECOMMENDED CIRCUIT SCHEMATIC
Vcc3.3V
TDZ=50R
LVPECL
TD+
TDTD+
TDis
Veet
Vcct
TXDis(LVTTL)
10
9
8
7
6
Z=5OR
Vcc3.3V
1uH
10nF
10nF
10uF
10uF
PHY DEVICE
1
2
3
4
5
Veer
Vccr
SD
RDRD+
1uH
10nF
Vcc3.3V
10uF
RD+
100R
LVPECL
Z=50R
RDZ=5OR
SD
TO LVTTL STAGE
Note: 1. Veer and Veet are not internally connected to each other.
2. 50 Ω line pattern and component placements on TD+/TD- and RD+/RD- lines shall be symmetrical for
better impedance matching.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
TRML-9100FG
4
***********************************************************************************************************************************************************************
PACKAGE DIAGRAM
Units in mm
1) Standard Case
TRML-9100FG / TRML-9100FAG
2) Extended Case
TRML-9100FEG / TRML-9100FAEG
Note: Specifications subject to change without notice.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
12/1/2005 V2.0