Designed and Manufactured in Germany Specification Oscillator type: Rev.: 1 Date: 2014-08-26 AXIOM1000 UHF Ultra-Low Phase Noise OCXO in Connectorized Package Parameter Frequency range Standard frequencies Frequency stability Initial tolerance @ +25°C vs. operating temperature range vs. supply voltage variation (pushing) vs. load change (pulling) Long term (aging) per day st Long term (aging) 1 year Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (∆f / ∆VC) EFC input impedance RF output Signal waveform Load RL Output level Harmonics Sub-harmonics (multiples of fOUT/10) Spurious Warm-up time @ +25°C Phase noise @ 1000 MHz (Note 4) Supply voltage VS Current consumption (steady state) Current consumption (warm-up) Enclosure (see drawing) (LxWxH) Weight Packing Notes: 1. 2. 3. 4. 5. min. typ. 300 max. Unit Condition 1500 MHz MHz ±300 Option 1 & 2 See tables 1 & 2 ±10 ±5 ±1 ±2 ±100 ±200 ppb @ VC = 5.0 V steady state ppb ppb ppb ppb VS ±5% RL ±5% after 30 days operation after 30 days operation 1000.000 ±1 1.0 ±2 5.0 Positive 9.0 100 +11 kΩ Sine wave 50 +13 -40 -45 -115 -143 -150 11.4 ppm V 12.0 +15 -35 -40 -90 5 -110 -140 -145 -150 12.6 300 700 50.0x50.0x21.0 max. 60 Palette Ω dBm dBc dBc dBc min dBc/Hz dBc/Hz dBc/Hz dBc/Hz V mA mA ±5% (Note 2) (Note 3) ∆ffinal/f0 < ±0.1 ppm @ 100 Hz @ 1 kHz @ 10 kHz @ ≥100 kHz (Note 5) @ +25°C mm g Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Other output level on request Depending on frequency multiplication factor may be lower or higher than 10 Please consult factory for phase noise of other frequencies Other supply voltages on request GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM1000 Rev.1 Drawing D0 Page 1(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Absolute Maximum Ratings Parameter min. max. Supply Voltage VS Control Voltage VC Storage Temperature -0.5 -0.5 -55 VS + 10% 15 +125 Unit Condition V V °C VS to GND VC to GND Frequency stability vs. temperature Stability [ppb] ±5 ±10 ±25 ±50 ±100 ±200 Option 1 05 10 25 50 100 200 Table 1 Temperature range [°C] 05 0 ~ +50 -10 ~ +60 -20 ~ +70 -30 ~ +70 -40 ~ +75 -40 ~ +85 -55 ~ +85 Table 3 “Availability” Lower Temperature Option 2 T [°C] 0 0 1 -10 2 -20 3 -30 4 -40 5 -55 Table 2 10 O O O - Upper Temperature Option 2 T [°C] A +50 B +60 C +70 D +75 E +80 F +85 Standard: “1B” = -10°C to +60°C Frequency stability [Option 1] 25 50 100 X X X X X X X X X O X X O O X O X X 200 X X X X X X X X = available, O = available on request, - not available Ordering Code Option 1 Option 2 [Stability] [Temperature range] AXIOM1000 Table 1 Table 2 Example: AXIOM1000-25-1B_Rev.1 – 1000.000 MHz Model Handling and Testing Parameter Handling and Testing Processing Parameter Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS- Compliant GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Revision Frequency [MHz] Rev.1 1000.000 Procedure Application Note AXAN-011 Application Note AXAN-012 Procedure IEC60749-26 IEC60749-27 Yes Yes AXIOM1000 Rev.1 Drawing D0 Page 2(4) HBM MM No No Source www.axtal.com www.axtal.com Condition 2000 V 200 V www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing Pin connections: Pin # Symbol 1 VS 2 GND 3 VC SMA RF OUT Function Supply Voltage Ground Control Voltage (EFC) RF Output * See Application Note AXAN-011 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM1000 Rev.1 Drawing D0 Page 3(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] Remarks Author Checked 1 D0 26.08.2014 First issue HH HH GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM1000 Rev.1 Drawing D0 Page 4(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]