Specification Oscillator type: Rev.: 1 Date: 2014-06-20 AXIOM5050M Low Phase Noise OCXO with Multiple Outputs Parameter Frequency range Frequency stability Initial tolerance @ +25°C vs. operating temperature range vs. supply voltage variation (pushing) vs. load change (pulling) Long term (aging) per day st Long term (aging) 1 year Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (∆f / ∆VC) EFC input impedance RF output RF output ports (Note 2) Signal waveform Load RL Output level (each port) Isolation between RF ports Harmonics Spurious Warm-up time @ +25°C Phase noise Supply voltage VS (Note 4) Current consumption (steady state) Current consumption (warm-up) Enclosure (see drawing) (LxWxH) Weight Packing Notes: 1. 2. 3. 4. min. typ. max. Unit 96.000,mnbnbbn, 50 150 MHz ±300 Option 2 & 3 See tables 1 & 2 ±10 ±5 ±1 ±2 ±100 ±200 ±1 0 ±2 5.0 Positive 10.0 100 Condition ppb @ VC = 5.0 V steady state ppb ppb ppb ppb VS ±5% RL ±5% after 30 days operation after 30 days operation ppm V kΩ 2, 4, 6 Sine wave 50 Option 1 Ω dBm dB dBc dBc min +5 30 11.4 -30 -90 3 5 Consult factory 12.0 12.6 V 300 mA 500 mA 50.0x50.0x21.0 max. 60 Palette ±5% (Note 3) ∆ffinal/f0 < ±0.1 ppm @ +25°C mm g Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Odd number of ports on request Higher output level on request. Unused ports must be terminated with 50 Ω Other supply voltage on request Absolute Maximum Ratings Parameter min. max. Supply Voltage VS Control Voltage VC Storage Temperature -0.5 -0.5 -55 VS + 10% 15 +125 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM5050M Rev.1 Drawing D0 Page 1(4) Unit Condition V V °C VS to GND VC to GND www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Frequency stability vs. temperature Stability [ppb] ±5 ±10 ±25 ±50 ±100 ±200 Option 2 05 10 25 50 100 200 Table 1 Temperature range [°C] 05 0 ~ +50 O -10 ~ +60 O -20 ~ +70 O -30 ~ +70 O -40 ~ +75 -40 ~ +85 -55 ~ +85 Table 3 “Availability” Lower Temperature Option 3 T [°C] 0 0 1 -10 2 -20 3 -30 4 -40 5 -55 Table 2 10 X X X O O - Upper Temperature Option 3 T [°C] A +50 B +60 C +70 D +75 E +80 F +85 Standard: “1B” = -10°C to +60°C Frequency stability [Option 2] 25 50 100 X X X X X X X X X X X X X X X O X X O X X 200 X X X X X X X X = available, O = available on request, - not available Ordering Code Option 1 Option 2 Option 3 [Output ports] [Stability] [Temperature range] AXIOM5050M 2, 4, 6 Table 1 Table 2 Example: AXIOM5050M-6-25-1B_Rev.1 – 100.000 MHz Model Handling and Testing Parameter Handling and Testing Processing Parameter Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS- Compliant GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Revision Frequency [MHz] Rev.1 100.000 Procedure Application Note AXAN-011 Application Note AXAN-012 Procedure IEC60749-26 IEC60749-27 Yes Yes AXIOM5050M Rev.1 Drawing D0 Page 2(4) HBM MM No No Source www.axtal.com www.axtal.com Condition 2000 V 200 V www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Enclosure drawing Pin connections: Pin # Symbol Function 1 VS Supply Voltage 2 GND Ground 3 VC Control Voltage (EFC) SMA (6x) RF OUT RF Outputs Ports 2 4 6 SMA Connectors * SMA S3 – S4 SMA S2 – S5 SMA S1 – S6 *Unused connectors are not present * See Application Note AXAN-011 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM5050M Rev.1 Drawing D0 Page 3(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] Remarks Author Checked 1 D0 20.06.2014 First issue HH HH GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM5050M Rev.1 Drawing D0 Page 4(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]