PRODUCT SPECIFICATION HDA1040ST-AH 10.4”, TFT SVGA (800 X 600) COLOR LCD DISPLAY MODULE HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 1 OF 16 HDA1040ST-AH DATE: 10/14/11 1. Overview HDA1040ST-AH Display Module is a color active matrix a-Si TFT-LCM that uses amorphous silicon TFT as a switching device. This model is composed of a TFT-LCD panel , a driving circuit and 4-wire resistance touch Panel. This touch TFT LCD module has a high resolution (800 x (R.G.B) X 600) and can display up to 262,144 colors. Because it has builtin power supply circuit, the LCD power supply voltage is only 3.3V. The most important thing is that this touch module with high brightness LED backlight. The brightness is reach 800 cd/m2 with the touch panel. General specifications are summarized in the following table: It em Specifications unit Panel Size 10.4 (panel Diagonal) inch Display Area 211.2 (W) x 158.4(H) mm Number of Pixels 800(H) x 3(RGB) x 600(V) - Pixel pitch 88 (W) x 264 (H) um Overall dimension 236.0(W)x176.9(H)x7(D) Color configuration R.G.B -stripe mm - Display Mode Normally white mm Number of colors 262,144 colors Brightness 800 cd/m Backlight Unit LED Electrical Interface LVDS 6 bits (data) Weight 300 Touch Panel With 4-wire Resistance Touch Panel Surface Treatment Anti-Glare 3H HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. 2 g REV.: 1.0 SHEET 2 OF 16 HDA1040ST-AH DATE: 10/14/11 HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 3 OF 16 HDA1040ST-AH DATE: 10/14/11 HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 4 OF 16 HDA1040ST-AH DATE: 10/14/11 (4)Definition of Luminance Uniformity : Measured Maximum luminance[L(MAX)] and Minimum luminance[L(MIN)] on the 5 points Luminance Uniformity is calculated with the following formula : ? L =[ L(MIN) / L (MAX) ] X 100% (5)Definition of Viewing Angle HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 5 OF 16 HDA1040ST-AH DATE: 10/14/11 4. ELECTRICAL CHARACTERISTICS Item LVDS Differential input high threshold Threshold LVDS Differential input low Differential input voltage` LVDS input common mode Voltage Input current Supply Voltage Common Electrode Driving Signal Sync Frequency VDD Power Consumption Symbol Min. Typ. Max Unit Remarks VTH - - 100 mV VTL -100 - - mV VID 0.1 - 0.6 V VCMLVDS VID /2 - IIN VDD -10 3.0 3.3 VCOM - 4.36 - V Note (1) FVD IDD - 60 260 70 380 H mA Note (2) VCMLVDS =1.2V 1.4-( VID/2) 10 3.6 V uA V LVDS DC timing diagram Note (1) : The value may be different for different LCM. Note (2) : To test the current dissipation, using the “color bar” testing pattern shown as below: Current dissipation testing pattern HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 6 OF 16 HDA1040ST-AH DATE: 10/14/11 HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 HDA1040ST-AH SHEET 7 OF 16 DATE: 10/14/11 HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 8 OF 16 HDA1040ST-AH DATE: 10/14/11 7. INTERFACE Connector : Starconn 107A20-0021RA-G3-R LVDS CONNECTOR: Pin no 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VDD VDD Gnd Gnd IN0IN0+ Gnd IN1IN1+ Gnd IN2IN2+ Gnd CLKCLK+ Gnd NC NC Gnd Gnd Matching connector : Hirose DF19K-20P-1H (56) Function POWER SUPPLY:3.3V POWER SUPPLY:3.3V Power Ground Power Ground Transmission Data of Pixels Transmission Data of Pixels Power Ground Transmission Data of Pixels 1 Transmission Data of Pixels 1 Power Ground Transmission Data of Pixels 2 Transmission Data of Pixels 2 Power Ground Sampling Clock Sampling Clock Power Ground No Connect No Connect Power Ground Power Ground Back Light Connector: Connector : JST BHSR-02VS-1 Pin No 1 2 Symbol Function LEDA LED driving anode (high voltage) LEDK LED driving cathode (low voltage) HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 Wire Color Red White SHEET 9 OF 16 HDA1040ST-AH DATE: 10/14/11 8. AC Timing characteristic of the LVDS Timing Parameter: Symbol Item Clock per i od Clock high time Clock low time PLL wake-up time Input skew mar i gn HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 tLVCP tLVCH tLVCL tLVPLL tLVSKM Q.A.: Z.W. Min 20 .0 . Typ 25 14 .29 10 .71 Max 31.25 Condition ns . ? 400 n5 ? '5 ps REV.: 1.0 Unit ns f=85MHz SHEET 10 OF 16 HDA1040ST-AH DATE: 10/14/11 Recommended Input Timing of LVDS transmitter Parameter Symbol Dclk frequency Horizontal Section Min. Typ. Max. Unit 1/Tclk 32 40 50 MHz Horizontal total Th 866 1056 1064 Tclk Horizontal blanking Thb 66 256 264 Tclk Valid Data Width Thd 800 800 800 Tclk Vertical Frame rate - - 60 70 Hz Section Vertical total Tv 604 628 800 Th Vertical blanking Tvb 4 28 200 Th Valid Data Width Tvd 600 600 600 Th Note : DE signal is necessary. HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 11 OF 16 HDA1040ST-AH DATE: 10/14/11 Power On/ Off Sequence Item Symbol Min. Typ. Max. Unit VDD 3.0V to signal starting Tp1 0 - 50 ms Signal starting to backlight on Tp2 150 - - ms Signal off to VDD 3.0V Tp3 0 - 50 ms Backlight off to signal off Tp4 150 - - ms HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 12 OF 16 HDA1040ST-AH DATE: 10/14/11 9 . QUALITY AND RELIABILITY 9.1 TEST CONDITIONS Tests should be conducted under the following conditions : Ambient temperature Humidity : : 25 ± 5°C 60 ± 25% RH. 9.2 SAMPLING PLAN Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan . 9.3 ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation. 9.4 APPEARANCE An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under florescent light. The inspection area of LCD panel shall be within the range of following limits. HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 13 OF 16 HDA1040ST-AH DATE: 10/14/11 HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 14 OF 16 HDA1040ST-AH DATE: 10/14/11 9.6 Reliability Test Test Item Test Conditions Note High Temperature Operation 70±3°C , t=96 hrs Low Temperature Operation -20±3°C , t=96 hrs High Temperature Storage 80±3°C , t=96 hrs 1,2 Low Temperature Storage -30±3°C , t=96 hrs -20°C ~ 25°C ~ 70°C 30 m in. 5 min. 30 min. ( 1 cycle ) Total 5 cycle 1,2 Thermal Shock Test Humidity Test 1,2 1,2 60 °C, Humidity 90%, 96 hrs Sweep frequency : 10 ~ 55 ~ 10 Hz/1min Amplitude : 0.75mm Vibration Test (Packing) Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions 2 (15-35°C , 45-65%RH). Definitions of life end point : ? Current drain should be smaller than the specific value. ? Function of the module should be maintained. ? Appearance and display quality should not have degraded noticeably. ? Contrast ratio should be greater than 50% of the initial value. HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 Q.A.: Z.W. REV.: 1.0 SHEET 15 OF 16 HDA1040ST-AH DATE: 10/14/11 HANTRONIX, INC. 10080 BUBB RD. CUPERTINO, CA 95014 SHEET 16 OF 16 Z.W. 1.0 HDA1040ST-AH DATE: 10/14/11