AM-640480G2TNQW-A0H - OLED-LCD-TFT

SPECIFICATIONS FOR
LCD MODULE
CUSTOMER
CUSTOMER PART NO.
AMPIRE PART NO.
APPROVED
AM-640480G2TNQW-A0H
BY
DATE
†Approved For Specifications
;Approved For Specifications & Sample
AMPIRE CO., LTD.
2F., No.88, Sec. 1, Sintai 5th Rd., Sijhih City, Taipei County 221, Taiwan (R.O.C.)
台北縣汐止市新台五路一段 88 號 2 樓(東方科學園區 D 棟)
TEL:886-2-26967269 , FAX:886-2-26967196 or 26967270
APPROVED BY
Date : 2009/7/8
CHECKED BY
AMPIRE CO., LTD.
ORGANIZED BY
1
RECORD
OF
REVISION
Revision
Date
Page
Contents
Editor
2009/7/8
--
New Release
JOHN
Date : 2009/7/8
AMPIRE CO., LTD.
2
1. INTRODUCTION
This is a color active matrix TFT-LCD that uses amorphous silicon TFT as a switching
device . This model is composed of a 5.7inch TFT-LCD panel , a driving circuit and LED
backlight system . This TFT-LCD has a high resolution (640(R.G.B) X 480) and can
display up to 262,144 colors.
1-1. Features
● VGA Resolution
● 6 Bits color driver with LVDS interface
● Wide range operation temperature
2. PHYSICAL SPECIFICATIONS
Item
Specifications
unit
640RGB (W) x 480(H)
dots
Display area
115.2 (W) x 86.4 (H)
mm
Pixel pitch
0.18 (W) x 0.18 (H)
mm
Color configuration
R.G.B Vertical stripe
Overall dimension
127.0(W)x98.43(H)x7.5(D)---(Typ)
Surface treatment
Antiglare , Hard-Coating(3H)
Display resolution(dot)
Brightness
500
Contrast ratio
250 : 1
Backlight unit
LED
Display color
262,144
Viewing Direction
Display Mode
Date : 2009/7/8
mm
cd/m2
colors
12 o’clock
Normally White
AMPIRE CO., LTD.
3
3. ABSOLUTE MAXIMUM RATINGS
ITEM
SYMBOL
MIN
MAX
Vcc
-0.5
5
V
DCLK , DE
R0~R5
G0~G5
B0~B5
-0.5
Vcc + 0.5
V
Operation Temperature
Top
-20
70
℃
Storage Temperature
Tstg
-30
80
℃
Power Supply Voltage
Signal Input Voltage
UNIT NOTE
4. ELECTRICAL CHARACTERISTICS
4-1 TFT LCD Module voltage
ITEM
SYMBOL
MIN
TYP
MAX
UNIT
Power Voltage For LCD
VCC
3.0
3.3
3.6
V
Power Voltage For VLED
VDD
--
5.0
--
V
VIH
VCC*0.7
--
VCC
V
VIL
0
--
VCC*0.3
V
VIH
3.0
--
5.0
V
VIL
GND
--
0.3
V
Logic Input Voltage
ADJ Input Voltage
Date : 2009/7/8
AMPIRE CO., LTD.
4
NOTE
4-2 TFT LCD current comsumption
ITEM
SYMBOL
MIN
TYP
MAX
UNIT
NOTE
LCD Power Current
Icc
-
106
-
mA
(1)
LED Power Current
ILED(VLED=5V)
-
290
-
mA
NOTE :
(1) Typ : under 64 gray pattern Max : under black pattern
(a) 64 Gray Pattern
Date : 2009/7/8
AMPIRE CO., LTD.
(b) Black Pattern
5
6. INTERFACE
LVDS J2:
Pin no
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Symbol
VDD
VDD
Gnd
Gnd
IN0IN0+
Gnd
IN1IN1+
Gnd
IN2IN2+
Gnd
CLKCLK+
Gnd
NC
NC
Gnd
Gnd
Function
POWER SUPPLY:3.3V
POWER SUPPLY:3.3V
Power Ground
Power Ground
Transmission Data of Pixels
Transmission Data of Pixels
Power Ground
Transmission Data of Pixels 1
Transmission Data of Pixels 1
Power Ground
Transmission Data of Pixels 2
Transmission Data of Pixels 2
Power Ground
Sampling Clock
Sampling Clock
Power Ground
No Connect
No Connect
Power Ground
Power Ground
LED J3:
Pin no
1
2
3
4
Symbol
GND
VLED
VLED
ADJ
Power Ground
Power Supply for LED 5V
Power Supply for LED 5V
Adjust for LED Brightness
Function
*Note
NOTE :
1. ADJ adjust brightness to control Pin , Pulse duty the bigger the brighter.
Date : 2009/7/8
AMPIRE CO., LTD.
6
2. ADJ signal = 0 ~ 5.0V , operation frequency : 300Hz~1KHz
3. VSS Pin must ground contact , can not be floating.
Date : 2009/7/8
AMPIRE CO., LTD.
7
7. AC Timing characteristic of the LVDS
Date : 2009/7/8
AMPIRE CO., LTD.
8
Date : 2009/7/8
AMPIRE CO., LTD.
9
8. OPTICAL CHARACTERISTICS
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Note
Contrast ratio
CR
200
250
--
--
(1)(2)(3)
Luminance
Lw
--
500
-
cd/m2
(1)(3)
Luminance Uniformity
ΔL
70
75
-
%
(1)(3)
--
50
--
ms
(1)(3)(5)
80
100
-
120
140
-
Deg.
(1)(2)(4)
0.566
0.616
0.666
0.302
0.352
0.402
0.308
0.358
0.408
0.518
0.568
0.618
0.096
0.146
0.196
--
(1)(3)
0.086
0.136
0.186
0.296
0.346
0.396
0.328
0.378
0.428
Response Time
( White – Black )
Viewing
Angle
Tr +Tf
Vertical
Θ
Horizontal
Φ
Red
Color
chromaticity
Point - 5
Θ=Φ=0°
Green
Blue
White
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
CR≧10
Point – 5
Point - 5
Θ=Φ=0°
NOTE :
(1) Measure conditions : 25℃±2℃ , 60±10%RH under 10Lux , in the dark room by
BM-7TOPCON) ,viewing 2° , VCC=3.3V , VDD=3.3V
(2) Definition of Contrast Ratio :
Contrast Ratio (CR) = (White) Luminance of ON ÷ (Black) Luminance of OFF
(3) Definition of Luminance :
Definition of Luminance Uniformity
Measure white luminance on the point 5 as figure9-1
Measure white luminance on the point 1 ~ 9 as figure9-1
ΔL = [ L(MIN) / L(MAX)] X 100%
Date : 2009/7/8
AMPIRE CO., LTD.
10
(4) Definition of Viewing Angle(Θ,Φ), refer to Fig9-2 as below :
(5) Definition of Response Time.(White – Black)
Date : 2009/7/8
AMPIRE CO., LTD.
11
9. INCOMING INSPECTION STANDARD FOR TFT-LCD PANEL
DEFECT TYPE
Note
LIMIT
φ<0.15mm
SPOT
FIBER
VISUAL
DEFECT
INTERNAL
POLARIZER
BUBBLE
Mura
0.15mm≦φ≦0.5mm
0.5mm<φ
0.03mm<W≦0.1mm, L≦
5mm
1.0mm<W, 1.5mm<L
φ<0.15mm
0.15mm≦φ≦0.5mm
0.5mm<φ
DARK DOT
TWO ADJACENT DOT
N=0
N≦3
N=0
Ignore
N≦2
N=0
Note1
B Grade
Total
C Area O Area
Total
Note3
N≦0
N≦2
N≦2
N≦2
N≦3
N≦5
Note2
N≦2
N≦3
N≦3
N≦3
N≦5
N≦8
N≦5
N≦6
N≦8
Note2
N≦1
pair
N≦1
pair
N≦1
pair
Note4
N≦4
N≦0
N≦1
pair
N≦1
pair
THREE OR MORE
NOT ALLOWED
ADJACENT DOT
LINE DEFECT
NOT ALLOWED
(1) One pixel consists of 3 sub-pixels, including R,G, and B dot.(Sub-pixel = Dot)
(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter
[Note1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter
[Note2] Bright dot is defined through 6% transmission ND Filter as following.
Date : 2009/7/8
Note1
C Area O Area
TOTAL DOT
ELECTRICAL
DEFECT
Note1
It’ OK if mura is slight visible through
6%ND filter
A Grade
BRIGHT DOT
Ignore
N≦4
AMPIRE CO., LTD.
12
[Note3]
C Area: Center of display area
C Area: Outer of display area
[Note4]
Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status)
adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2
defect dots in total quantity.
(1) The defects that are not defined above and considered to be problem shall be reviewed
and discussed by both parties.
(2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted.
Date : 2009/7/8
AMPIRE CO., LTD.
13
10. RELIABILITY TEST CONDITIONS
ITEM
CONDITIONS
HIGH TEMPERATURE OPERATION
70℃ , 240Hrs
HIGH TEMPERATURE AND HIGH
HUMIDITY OPERATION
60℃ , 90%RH , 240Hrs
HIGH TEMPERATURE STORAGE
80℃ , 240Hrs
LOW TEMPERATURE OPERATION
-20℃ , 240Hrs
LOW TEMPERATURE STORAGE
-30℃ , 240Hrs
-30℃(0.5Hr) ~80℃(0.5Hr)
200Cycle
THERMAL SHOCK
10.1 OTHERS
AMIPRE will provide one year warranty for all products and three months warrantee for
all repairing products.
Date : 2009/7/8
AMPIRE CO., LTD.
14
11. OUTLINE DIMENSION
Date : 2009/7/8
AMPIRE CO., LTD.
15
Date : 2009/7/8
AMPIRE CO., LTD.
16