Side 2 8 9a Install Tool-less CD-ROM or DVD-ROM Drive 2 1 1 2 3 4 Remove EMI shield from 5.25-inch device drive bay. 5 6 Move latch to "lock" position. Make sure latch is in "unlock" position. 4 Insert CD-ROM or DVD-ROM drive into device drive bay. Line up holes in CD-ROM or DVD-ROM drive with holes in chassis. 4 5 6 Pow er 6 Data 1 5 3 3 Data cables are included with the Intel® Server Board. (If installing a hot-swap drive cage, go to Step 10) 10 7 8 2 1 11 Install Hot-Swap Drive Cage Kit (Optional) Complete Server Board Connections 12 Insert fixed drive cage into chassis. Pull the drive latch forward for the drive bay you want to install a hard drive in. Drive slots 1, 3, and 5 MUST be populated first. Failure to do so could result in thermal issues within chassis. Route power and data cables through cable routing area at the bottom of the fixed drive cage. 13 Install PCI Card Guide Fan Connection Fan Header Used Notes System Fan 1 PCI Zone Chassis Fan System Fan 2 HDD Cage Fan System Fan 3 Rear Chassis Fan If you intend to configure your server with SATA/SAS hot swap hard drives, go to the instructions that came with your drive cage upgrade kit to install the drive cage and hot-swap drives. 9 4 Insert fixed hard drive into drive bay until it stops. Ensure that the power and data connector end of the hard drive is facing forward. 1 2 See your Intel ® Server Board Quick Start 1 1. See your Intel Server Board Quick Start User's Guide to connect your keyboard, mouse, video and other I/O cables. ® 2. Connect the AC power cable last. CAUTION: Power supply requires a 16-gauge power cord. BIOS, Drivers, and Operating System Install A. Confirm BIOS Version: Look on the Reference Hot Swap Conversion Kit 6-Drive SAS/SATA Hot Swap Cage without expander APPTHSDBKIT AXX6DRV3GR 1 Server/System Management screen in the BIOS Setup Utility to determine the installed BIOS version. Compare this to the versions at: 6-Drive SAS/SATA Hot Swap Cage with expander AXX6DRV3GEXP Intel® Server Chassis Rack Mount Kit APP3RACKIT If new versions are available, update the BIOS on your server. See the User Guide on the Intel® Server Deployment Toolkit CD for update instructions. IIntel® Server System SC5650BCDP Product Maintenance Kit http://support.intel.com/support/motherboards/server/S5500BC/ B. Configure your RAID Controller: Use the instructions provided with the RAID controller. C. Install your Operating System: Use the instructions provided with the RAID controller and with the operating system. D. Install Operating System Drivers: With the operating system running, insert the Intel® Server Deployment Toolkit CD. If using a Microsoft* Windows*operating system, the Express Installer will autorun and allow you to select the appropriate drivers to install. On other operating systems, browse the CD folders to locate and install the driver files. 1 1 2 APPTPMKIT 1 Requires a Hot Swap Conversion Kit to integrate into the Intel® Server System SC5650BCDP. B B. C A complete list of accessories and spares can be found at: http://support.intel.com D Available Documents Document Type Content Technical Product Specification In-depth technical information Spares and Configuration Guide Supported accessories and spares list Software and Drivers Up-to-date firmware, driver and utility information Additional Reference Documents available at: http://support.intel.com A. C. D. E. F. E G F H G. H. 2 Server Board S5500BC Component Layout F 1 Slide the side cover on chassis and latch securely. 2 Replace screws. USB 0-1 VGA BMC SATA 2 SATA 5 SATA 1 Power/Sleep LED Power/Sleep Button NMI Button Reset Button NIC 1 Activity LED NIC 2 Activity LED Hard Drive Activity LED Status LED See your Intel® Server System S5500BCDP User's Guide for expanded component and connection information. SATA 0 SATA 3 SATA SGPIO SATA 4 DIMM Fault LEDs CAUTION: This chassis must be operated with the SIDE COVER installed to ensure proper cooling. Note: Refer to the Technical Product Specification for Diagnostic LED decoder list. USB 2-3 Front Panel Controls and Indicators A Close the back panel PCI add-in board retention device. B 1 1 Install Software 4 A 3 Accessories and Order Codes While holding the PCI add-in board by its top edge or upper corners, firmly press the add-in board into the expansion slot. 1 ICH10 NIC 2 USB 9 USB 8 NIC 1 USB 7 USB 6 G A. Front Panel B. 5.25-inch Device Drive Bays (2) C. Hard Drive Cage Access Door D. Door Lock C E. USB Ports (2) F. Fan Duct and System Fan (DP/WS/BRP configuration shown) D G. Hard Drive Cage Retention Mechanism E Diagnostic LEDs BIT3 BIT4 BIT2 BIT5 BIT1 BIT6 LSB MSB Status LED ID LED Serial A Battery Serial B IPMB_1 HSBP_A SYS FAN 3 SATA RAID Key O P H Q I Main Power IOH P/S AUX DIMM Fault LEDs J CPU 1 Socket CPU 2 Socket Front Panel Header Finishing Up 20 3 DIMM_B1 19 Remove the PCI slot shield by pressing the shield out from the inside of the chassis. 3 Chassis Features and Components DIMM_A2 2 3 Rotate left side of bezel assembly toward chassis. Snap two bezel tabs into corresponding recesses at left edge of chassis front panel. Slot 7 (PCI Express* x8) If you intend to configure your server as a rack-mount system, go to the instructions that came with your Rack Mount Kit to complete your server assembly. 2 2 3 4 1 Slot 6 (PCI Express* x8, Riser Card) Secure foot by inserting pin through the rubber foot. Note: Repeat above steps until all four feet are installed. If you intend to configure your server as a pedestal system, disregard this step and proceed to Step 17. Close System Slot 5 (PCI Express* x4) Insert rubber foot into chassis hole. Engage three clips at right edge of chassis. RMM3 1 2 1 18 Install Front Bezel Assembly Slot 4 (PCI 32/33) Note: This step applies to the pedestal version only. If you plan to configure your chassis as a rack mount system, go to Step 16. 17 Install Rack Mount Kit (Optional) Slot 3 (PCI Express* x4) Remove the bezel filler panels for each drive you have installed. Release plastic tabs located at back side of bezel and pull out filler panels from front. 16 Install Feet DIMM_D2 15 Remove Filler Panels Install additional drives as necessary. Swing PCI card guide into chassis until right-side blue tabs snap into place. DIMM_B2 1 2 Tighten thumb screw. Insert tabs on left side of PCI card guide into slots in chassis. From inside of chassis, press open the back panel PCI add-in board retention device. DIMM_A1 Re-attach drive cage EMI shield to chassis. DIMM_E2 9 6 2 DIMM_D1 14 8 Push drive latch in to lock hard drive into drive bay. 1 DIMM_E1 Install power and data cables to each of the installed drives. The cables route through the oval opening at the bottom of the drive cage. 5 Install PCI Add-in Boards User's Guide or the User Guide for server board cable connections. 7 5 4 3 Connect power (P5 or P6) cables and data cables to rear of the CD-ROM or DVD-ROM Install Tool-less Fixed Hard Drives 3 1 2 An additional 4-pin IDE male-to-SATA 15 pin power cable adapter may be needed if the CD-ROM or DVD-ROM does not have a 4-pin power connector. 9b Install Tool-less Fixed Hard Drives (If installing a hot-swap drive cage, go to Step 10) (Continued...) K R L M N SYS FAN 2 CPU 1 FAN CPU Power SYS FAN 1 CPU 2 FAN H. Alternate external SCSI Knockout I. Fixed Hard Drive Fan J. SC5650BCDP Mother Board K. Padlock Loop L. PCI Card Guide M. External SCSI Knockout N. Serial B port Knockout O. Power Supply (fixed illustrated) P. A/C Power In Q. I/O Shield R. PCI Add-in Board Slots