Eval Board

IS31AP2031 CLASS-G AUDIO POWER AMPLIFIER
EVALUATION BOARD GUIDE
DESCRIPTION
RECOMMENDED EQUIPMENT
The IS31AP2031 is a Class-G audio power amplifier
with automatic gain control. It drives up to 2.0W (10%
THD+N) into an 8Ω speaker from a 4.2V VCC supply.
The IS31AP2031 provides low cost, space saving
solution for portable equipments which need audio
output with higher power by boosting up supply voltage.
Its external components just include a few capacitors
and resistors (no inductor). The IS31AP2031 use fully
differential design to reduce RF noise. The
IS31AP2031 integrates de-pop circuitry to reduce pop
and click noise during power on/off or shutdown enable
operation. The IS31AP2031 also integrates thermal
and short circuit protection function.



FEATURES








Operates from 2.7V to 4.5V
2.0W into an 8Ω load from a 4.2V supply (10%
THD+N)
4 gain levels: 12dB, 16dB, 24dB, 27.5dB
AGC function
Pulse Count Control serial interface
8kV HBM ESD
Thermal and short-circuit protection
Available in QFN-20 (3mm × 3mm).
QUICK START
≤ 4.5V, 2A power supply
Audio source (i.e. MP3 player, Notebook PC, etc.)
An 8Ω speaker
ABSOLUTE MAXIMUM RATINGS

≤ 4.5V power supply
Caution: Do not exceed the conditions listed above; otherwise
the board will be damaged
PROCEDURE
The IS31AP2031 demo board is fully assembled and
tested. Follow the steps listed below to verify board
operation.
Caution: Do not turn on the power supply until all connections
are completed.
1)
2)
3)
4)
5)
6)
Connect an 8Ω (or larger) speaker across the
OUT- terminal and OUT+ terminal.
Connect the ground terminal of the power supply
to the GND and the positive terminal to the VCC.
Or connect DC power to connector (DC IN).
If the audio source is differential, remove jumper
JP1, connect the negative of the audio source to
the IN- terminal, and connect the positive of the
audio source to IN+ terminal.
If the audio source is single-ended, connect the
audio source to the IN- terminal, and close jumper
JP1; or connect audio source to the audio
connector (AUDIO IN) and close jumper JP1.
Turn on the power supply, and pay attention to the
supply current. If the current exceeds 1.5A,
please check for circuit fault.
Turn on the audio source.
Figure 1: Photo of IS31AP2031 Evaluation Board
ORDERING INFORMATION
Part No.
Temperature Range
Package
IS31AP2031-QFLS2-EB
-40°C to +85°C (Industrial)
QFN-20, Lead-free
Table 1: Ordering Information
For pricing, delivery, and ordering information, please contacts ISSI’s analog marketing team at
[email protected] or (408) 969-660.
Integrated Silicon Solution, Inc. – www.issi.com
Rev. B, 12/31/2014
1
IS31AP2031 CLASS-G AUDIO POWER AMPLIFIER
EVALUATION BOARD GUIDE
PERFORMANCE DESCRIPTION
SOFTWARE SUPPORT
The IS31AP2031 evaluation board has four buttons to
switch between the different modes. The operating
mode is indicated by an LED illuminated above the
appropriate buttons. The modes listed as below:
Please refer to the integrated program.
1)
2)
3)
4)
5)
Note: The Jumper JP3 is closed by default, if the JP3 is open,
the MCU will stop functioning, the SDB pin of the chip in a high
impedance state. The external MCU can be used to control the
board SD (TP7) point.
Mode1: gain level 12dB AGC OFF.
Mode2: gain level 16dB AGC ON.
Mode3: gain level 24dB AGC OFF.
Mode4: gain level 27.5dB: AGC ON.
Shutdown mode: close Jumper (JP2) enter
shutdown mode.
Please refer to the datasheet to get more information about
IS31AP2031.
Note: IS31AP2031 Audio Amplifier provides solely the Audio
function on the evaluation board.
U1
U2
VCC
3V
1
3
C8
1uF
2
VDD
VOUT
4,8
C9
10nF
SD
GND
BP
VCC
5
C10
1uF
C2
1uF
4
VDD
C7
0.1uF
JP2
CLOSE=SD
SDB 1
TP7
LDO
SDB
CP
CN
C3
15nF
R1
10K
6
IN+
C4
15nF
R2
10K
7
9
JP1
CLOSE=SE
TP1
CON1
DC IN
VCC
19
C5
4.7uF
TP5
IN-
TP4
C6
10uF
3
SD
TP3
CON2
AUDIO IN
12,17,18
AVIN
R3
100K
IN-
OUT+
IN+
OUT-
FS
GND
15 OUT+
CON3
SPK
13 OUT14,20
TP6
Speaker
IS31AP2031
C1
10uF
LED1 1
LED2 2
RST 4
VCC
R10
100K
27.5dB AGC ON
24dB AGC OFF
3V
U3
TP2
R11
100K
R12
100K
P0.0
P1.7
RST
3
K3
P0.1
P0.2
R13
100K
K4
VDD
8
16dB AGC ON
K2
9
12dB AGC OFF
K1
10
6
7
5
P0.3
P1.6
P0.4
INT1/P1.4
P0.5
INT0/P1.3
P0.6
15
T1/P0.7
TXD/P1.0
RXD/P1.1
R6
1K
D4
LED3
R7
1K
D3
LED2
R8
1K
D2
LED1
R9
1K
D1
20 LED4
3V
19 LED3
18
JP3
OPEN=EXT CTRL
17 P0.4
16 P0.5
14 SDB
T0/P1.2
OSC1
OSC2
GND
LED4
13
12
11
R4
NC
R5
100K
LPC922
VCC
TP8
3V
P0.5
P0.4
RST
GND
5
4
3
2
1
ICP
Figure 2: IS31AP2031 Application Schematic
Integrated Silicon Solution, Inc. – www.issi.com
Rev. B, 12/31/2014
2
IS31AP2031 CLASS-G AUDIO POWER AMPLIFIER
EVALUATION BOARD GUIDE
BILL OF MATERIALS
Name
Symbol
Audio Amplifier
U1
LDO
Qty
Supplier
Part No.
Class-G Audio Amplifier
1
ISSI
IS31AP2031
U2
Low-dropout Regulator
1
PAM
PAM3101
MCU
U3
Microcontroller
1
NXP
LPC922
Diode
D1~D4
Diode, LED Blue, SMD
4
Resistor
R1,R2
RES,10k,1/16W,±1%,SMD
2
Yageo
RC0603FR-0710KRL
6
Yageo
RC0603JR-07100KRL
RES,1k,1/16W,±5%,SMD
4
Yageo
RC0603JR-0701KRL
Not Connected
1
Resistor
Description
R3,R5,R10~R13 RES,100k,1/16W,±5%,SMD
Everlight 19-217/BHC-ZL1M2RY/3T
Resistor
R6~R9
Resistor
R4
Capacitor
C1,C6
CAP,10µF,10V,±10%,SMD
2
Yageo
CC0805KKX7R6BB106
Capacitor
C2
CAP, 1µF,16V,±10%,SMD
1
Yageo
CC0603KKX7R7BB105
Capacitor
C8,C10
CAP, 1µF,16V,±10%,SMD
2
Yageo
CC0805KKX7R7BB105
Capacitor
C3,C4
CAP, 15nF,16V,±10%,SMD
2
Yageo
CC0603KKX7R7BB153
Capacitor
C5
CAP, 4.7µF,10V,±10%,SMD
1
Yageo
CC0805KKX7R6BB475
Capacitor
C7
CAP, 0.1µF,16V,±10%,SMD
1
Yageo
CC0603KKX7R7BB104
Capacitor
C9
CAP,10nF,16V,±10%,SMD
1
Yageo
CC0603KKX7R7BB103
Button
K1~K4
Button SMD
4
Bill of Materials, refer to Figure 2 above.
Integrated Silicon Solution, Inc. – www.issi.com
Rev. B, 12/31/2014
3
IS31AP2031 CLASS-G AUDIO POWER AMPLIFIER
EVALUATION BOARD GUIDE
0
0
2
2
1
2
1
2
1
2
2
1
2
1
2
1
2
2
1
2
1
1
1
2
2
2
0
0
Figure 3: Board Component Placement Guide - Top Layer
Figure 4: Board PCB Layout - Top Layer
Integrated Silicon Solution, Inc. – www.issi.com
Rev. B, 12/31/2014
4
IS31AP2031 CLASS-G AUDIO POWER AMPLIFIER
EVALUATION BOARD GUIDE
0
0
2
2
1
2
1
2
1
2
2
1
2
1
2
1
2
2
1
2
1
1
1
2
2
2
0
0
Figure 5: Board Component Placement Guide - Bottom Layer
Figure 6: Board PCB Layout - Bottom Layer
Copyright © 2014 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its
products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services
described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information
and before placing orders for products.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or
malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or
effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to
its satisfaction, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc. – www.issi.com
Rev. B, 12/31/2014
5