ca_F1-F45.qxd:Layout 1 2/10/11 8:07 AM Page 1 ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 32 MIL-DTL-38999 Series IV Filter Connectors TKJB Table ofReceptacle Contents Jam Nut TKJB7 D THREAD B MTG FLAT A DIA. E DIA. MAX 1.118 (28.4) 1.082 (27.5) C THREAD .106 (2.7) .075 (1.9) 1.403 (35.636) MAX D THREAD B MTG FLAT A DIA. F DIA. 1.118 (28.4) 1.082 (27.5) C THREAD .106 (2.7) .075 (1.9) .090 (2.286) MAX 1.960 (49.636) MAX Crimp Piggyback Shell Shell size Code Size A Dia. Max. B Mtg. Flat (Max.) C* Thread 1.0-6g 0.100 R D Thread 1.0-6g 0.100 R E Dia. Max. F Dia. Max. 11 B .509 (12.93) .942 (23.93) 25 15 1.520 (38.6) .427 (10.85) C .634 (16.10) 1.066 (27.08) 28 18 1.642 (41.7) .541 (13.74) D .759 (19.28) 1.191 (30.26) 31 22 1.768 (44.9) .666 (16.92) 17 E .885 (22.48) 1.321 (33.56) 34 25 1.957 (49.7) .791 (20.09) 19 F 1.009 (25.63) 1.441 (36.61) 38 28 2.035 (51.7) .880 (22.35) 21 G 1.134 (28.80) 1.566 (39.78) 41 31 2.157 (54.8) 1.005 (25.52) 23 H 1.259 (31.98) 1.691 (42.96) 44 34 2.283 (58.0) 1.130 (28.70) 25 J 1.384 (25.15) 1.816 (46.13) 47 37 2.409 (61.2) 1.255 (31.880) Filter 13 15 F Dimensions shown in inches (mm) Specifications and dimensions subject to change F-32 www.ittcannon.com ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 33 MIL-C-81659 Rack and Panel Filter Connectors TDPX TDPX filter connectors are used primarily on commercial and military aircraft for radio and instrumentation equipment and are available in single thru four gang version with standard ARINC shells and polarizing posts. They are intermateable with the standard DPX connectors are available in 9 contact arrangements. Performance and Material Specifications MATERIALS AND FINISHES Description Material ELECTRICAL Finish Contacts Size Cadmium plate (yellow chro- Available Filter mate) Catalog Reference Gold over suitable underplate Voltage Rating Shell Aluminum alloy Contacts Copper alloy Insulator High grade plastic none Interfacial and Neoprene rubber none Ground Spring Beryllium copper Gold plate Polarizing Posts Stainless steel Passivate Peripheral Seals 22 20, 16 & 22 Low Freq. L 16 & 20 Mid Freq. Std. Freq. High Freq. Low Freq. M T H L 200 VDC - 120 VAC rms 400 Hz Current Rating (Amp DC) 5 amp 7.5 amp - size #20, 20 amp - size #16 Insulation Resistance, 2 min. electrification 20 amp 5,000 megohms minimum time max. at 25˚C and 100 VDC @ 100 VDC DWV, sea level, with 500 microamps max. 300 500 500 charge/discharge current VDC VDC VDC Capacitance at 1 KHz, 0.1 V rms 32,000 8,000 3,000 850 32,000 picofarads 45,000 12,000 5,000 1,300 45,000 Freq. MHz Attenuation per MIL-STD-220 at 25˚C with no applied Attenuation (dB) 0.1 2 min. - - - 2 min. 1 15 min. 2 min. - - 15 min. voltage or current. 2 20 min. 5 min. 2 min. - 20 min. 10 35 min. 20 min. 12 min. 2 min. 35 min. 100 60 min. 55 min. 50 min. 30 min. 50 min. 500 to 10,000 60 min. 60 min. 55 min. 50 min. 50 min. Pi Pi Pi Pi Pi Filter Type How to Order - Single Gang TDPX E B - 57 L 34 P - 00 01 FILTER SERIES PREFIX ENVIRONMENTAL SHELL STYLE CONTACT ARRANGEMENT CAPACITANCE INDICATOR SHELL TYPE CONTACT TYPE MODIFICATION POLARIZING POSITION FILTER SERIES PREFIX TDPX - Single gang ENVIRONMENTAL SHELL STYLE B - Polarized ARINC B shell (preferred) D - DPXA flange (less polarizing posts) See page 35. CAPACITANCE INDICATOR L - Low Frequency M - Mid Frequency T - Standard Frequency Note: Use of "T" omitted in past nomenclature. H - High Frequency N - No filters this gang. Standard DPX insert assembly. SHELL TYPE 33 - Male (plug) 34 - Female (receptacle) Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com CONTACT TYPE P-Pin; S-Socket F-33 MODIFICATION TDPXD None TDPXB 03 - Mounting holes countersunk 100˚ to .230 (5.84) dia. 23 - With floating eyelets. Consult factory. Filter E - For interfacial (pin) Delete for standard CONTACT ARRANGEMENT POLARIZING POSITION See pages 35-36. F ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 34 MIL-C-81659 Rack and Panel Filter Connectors TDPX Table of -Contents How to Order Multiple Gang TDPX 4 E - 57 T P 57 N P 57 M P 57 L P - 34 - 00 01 FILTER SERIES PREFIX GANGS IN SHELL ENVIRONMENTAL CONTACT ARRANGEMENT (Side A) FILTER TYPE CONTACT TYPE CONTACT ARRANGEMENT (Side B) FILTER TYPE CONTACT TYPE CONTACT ARRANGEMENT (Side C) FILTER TYPE CONTACT TYPE CONTACT ARRANGEMENT (Side D) CAPACITANCE INDICATOR CONTACT TYPE SHELL TYPE MODIFICATION NUMBER POLARIZING POSITION FILTER SERIES PREFIX TDPX - DPX series with solder termination. GANGS IN SHELL 2, 3, and 4 gang ENVIRONMENTAL E - For interfacial (pin) Delete for standard. CAPACITANCE INDICATOR (Each gang, as desired)* L - Low Frequency M - Mid Frequency T - Standard Frequency Note: Use of "T" omitted in past nomenclature H - High Frequency N - No filter this gang. Standard DPX insert assembly. CONTACT ARRANGEMENT See page 31 for applicable arrangements. Please specify each arrangement number as indicated in ordering nomenclature for 2, 3, or 4 gang. CONTACT TYPE P for pin; S for socket. Designation follows each arrangement as ordered for 2, 3, or 4 gang versions. (Printed circuit contact/termiation is available. Consult factory for specifications.) Filter SHELL TYPE 33B for male (ARINC B) 34B for female (ARINC B) 33 for male 34 for female Note: ARINC B specified for DPX2 only. POLARIZING POSITION (see pages 35-36) The last two digits in the four-digit dash number refer to the polarizing post position. When the last two digits are omitted, the polarizing posts will be assembled in position 01, but the position number is not stamped on the connector. This allows the customer to position the posts themselves nd then stamp the appropriate number on the shell. If the last two digits are 00, the polarizing posts are deleted. MODIFICATION NUMBERS - 0001 indicates standard design for all styles. TDPX2-33B: - 0301 - Mounting holes .120 dia. Countersunk 100˚ to .230 dia. TDPX2-34: - 0101 - With #4-40 clinch nuts in mounting holes. TDPX3-34: - 0101 - With 6 #4-40 clunch nuts in mounting holes. TDPX4-34: - 0101 - F With 10 #4-40 clinch nuts in mounting holes. Dimensions shown in inches (mm) Specifications and dimensions subject to change F-34 www.ittcannon.com ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 35 MIL-C-81659 Rack and Panel Filter Connectors TDPX Table of Contents Contact Arrangements 6 5 4 12 A2 3 11 16 10 24 30 Arrangement No. No. of Contacts & Wire Size 14 19 18 28 27 23 29 1 8 15 20 2 9 6 5 4 13 A1 13 19 17 22 12 21 26 26 11 6 5 4 3 2 1 13 12 11 10 9 8 7 6 19 23 22 21 20 19 18 17 16 5 13 7 18 25 17 24 18 40 30 29 39 28 38 37 Arrangement No. No. of Contacts & Wire Size 27 36 26 35 25 34 24 31 30 32 33 8 9 18 28 47 57 45 55 44 54 4 29 33 43 28 7 1 8 9 15 21 27 37 15 32 42 41 52 21 31 6 7 15 23 5 13 14 A1 14 22 14 21 20 4 12 3 11 2 10 1 9 8 25 24 23 22 21 20 19 18 17 35 34 33 32 31 30 29 28 27 26 45 44 43 42 41 40 39 38 37 36 17 16 15 14 20 29 30 40 29 28 27 42 41 40 39 51 50 49 54 53 13 26 36 25 35 34 3 33 32 45 45 #20 2 11 10 12 26 25 24 23 22 9 8 33 32 31 30 46 45 44 43 52 51 50 49 48 47 59 1 13 25 39 1 21 20 19 18 39 38 37 36 35 34 67 66 65 64 63 62 61 60 48 16 20 4 5 6 7 10 57 57 #20 Arrangement No. No. of Contacts & Wire Size 22 38 1 11 12 22 24 23 53 16 16 12 2 3 13 14 34 36 35 46 56 25 2 10 1 8 26 26 #16 40C1 39 #20, 1 coax 5 15 16 26 27 37 38 6 7 17 17 23 39 40 40 #20 19 3 11 9 25 15 24 31 4 12 2 10 32C2 30 #20, 2 coax 14 3 7 58 57 56 55 26 52 66 40 53 79 93 67 80 106 94 67 64 #20, 3 #16 106* 106 #22 NOTE: Consult factory for part numbers for special combinations of filter, group contacts and power contacts, and for availability of filter socket contacts, for each contact arrangement. Contacts – Pin and Socket Standard Contact Terminations Finish: Gold plate per MIL-G-45204, Type 1, Class 1, over nickel plate per QQ-N-290. A C DIA. .025 (0.64) DIA + EXTENSION MAX B DIA. Pin/Solder Pot Socket/Printed Circuit .025 (0.64) DIA + EXTENSION MAX Pin/Printed Circuit Contact Size C 20 .125 (3.18) .110 (2.79) .065 (1.65) .061 (1.55) .048 (1.22) .043 (1.09) .200 (5.08), .285 (7.24), .375 (9.52) 16 .170 (4.32) .150 (3.81) .103 (2.62) .097 (2.46) .078 (1.98) .069 (1.75) .200 (5.08), .285 (7.24), .375 (9.52) 22 .115 (2.92) .095 (2.41) .005 (1.40) .051 (1.30) .040 (1.02) .036 (0.91) .200 (5.08), .285 (7.24), .375 (9.52) Filter B F Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com PC Tail Extension Max. A F-35 ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 36 MIL-C-81659 Rack and Panel Filter Connectors TDPX Table of Contents Polarization Two Post Type Face View of Engaging End DPX2-33F or 33M DPX2-34F or 34M B B LEFT POST TOP TOP COUPLING MECHANISM A A RIGHT POST LEFT POST COUPLING MECHANISM RIGHT POST Three Post Type DPXB-33 DPXB-34 LEFT POST DPX2-33A or 33B LEFT POST CENTER POST TOP CENTER POST LEFT POST CENTER POST RIGHT POST A RIGHT POST B RIGHT POST DPX2-34A or 34B DPX3-33 DPX4-33 LEFT POST CENTER POST A TOP TOP LEFT POST OR KEY CENTER POST OR KEY CENTER POST RIGHT POST B RIGHT POST OR KEY TOP LEFT POST Filter RIGHT POST F Dimensions shown in inches (mm) Specifications and dimensions subject to change F-36 www.ittcannon.com ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 37 MIL-C-81659 Rack and Panel Filter Connectors TDPX Positions 1 2 3 4 5 6 Dark areas represent post Two Post Type 33 PLUG MALE SHELL Position 34 RECEPTACLE FEMALE SHELL Left Post Right Post Position Left Post Right Post Position Left Post Right Post Position Left Post Right Post 01 02 03 04 05 4 5 6 2 3 4 4 4 4 4 09 10 11 12 13 3 4 2 3 2 3 2 2 2 1 01 02 03 04 05 1 1 1 1 1 1 6 5 3 2 09 10 11 12 13 2 3 3 3 4 2 1 3 2 3 06 07 08 4 5 2 3 3 3 14 15 3 2 1 6 06 07 08 2 2 2 1 6 3 14 15 4 5 2 3 Three Post Type PLUG SHELL Left Post Center Post Right Post 01 02 03 04 05 1 2 3 4 5 1 1 1 1 1 1 1 1 1 1 51 52 53 54 55 3 4 5 6 1 2 2 2 2 2 5 5 5 5 4 01 02 03 04 05 4 4 4 4 4 4 4 4 4 4 4 3 2 1 6 51 52 53 54 55 6 6 6 6 1 3 3 3 3 3 2 1 6 5 4 06 07 08 09 10 6 1 2 3 4 1 1 1 1 1 1 6 6 6 6 56 57 58 59 60 2 3 4 5 6 2 2 2 2 2 4 4 4 4 4 06 07 08 09 10 4 5 5 5 5 4 4 4 4 4 5 4 3 2 1 56 57 58 59 60 1 1 1 1 1 3 3 3 3 3 3 2 1 6 5 11 12 13 14 15 5 6 1 2 3 1 1 1 1 1 6 6 5 5 5 61 62 63 64 65 1 2 3 4 5 2 2 2 2 2 3 3 3 3 3 11 12 13 14 15 5 5 6 6 6 4 4 4 4 4 6 5 4 3 2 61 62 63 64 65 2 2 2 2 2 3 3 3 3 3 4 3 2 1 6 16 17 18 19 20 4 5 6 1 2 1 1 1 1 1 5 5 5 4 4 66 67 68 69 70 6 1 2 3 4 2 2 2 2 2 3 2 2 2 2 16 17 18 19 20 6 6 6 1 1 4 4 4 4 4 1 6 5 4 3 66 67 68 69 70 2 3 3 3 3 3 3 3 3 3 5 4 3 2 1 21 22 23 24 25 3 4 5 6 1 1 1 1 1 1 4 4 4 4 3 71 72 73 74 75 5 6 1 2 3 2 2 3 3 3 2 2 1 1 1 21 22 23 24 25 1 1 1 1 2 4 4 4 4 4 2 1 6 5 4 71 72 73 74 75 3 3 4 4 4 3 3 2 2 2 6 5 4 3 2 26 27 28 29 30 2 3 4 5 6 1 1 1 1 1 3 3 3 3 3 76 77 78 79 80 4 5 6 1 2 3 3 3 3 3 1 1 1 6 6 26 27 28 29 30 2 2 2 2 2 4 4 4 4 4 3 2 1 6 5 76 77 78 79 80 4 4 4 5 5 2 2 2 2 2 1 6 5 4 3 31 32 33 34 35 1 2 3 4 5 1 1 1 1 1 2 2 2 2 2 81 82 83 84 85 3 4 5 6 1 3 3 3 3 3 6 6 6 6 5 31 32 33 34 35 3 3 3 3 3 4 4 4 4 4 4 3 2 1 6 81 82 83 84 85 5 5 5 5 6 2 2 2 2 2 2 1 6 5 4 36 37 38 39 40 6 1 2 3 4 1 2 2 2 2 2 1 1 1 1 86 87 88 89 90 2 3 4 5 6 3 3 3 3 3 5 5 5 5 5 36 37 38 39 40 3 4 4 4 4 4 3 3 3 3 5 4 3 2 1 86 87 88 89 90 6 6 6 6 6 2 2 2 2 2 3 2 1 6 5 41 42 43 44 45 5 6 1 2 3 2 2 2 2 2 1 1 6 6 6 91 92 93 94 95 1 2 3 4 5 3 3 3 3 3 4 4 4 4 4 41 42 43 44 45 4 4 5 5 5 3 3 3 3 3 6 5 4 3 2 91 92 93 94 95 1 1 1 1 1 2 2 2 2 2 4 3 2 1 6 46 47 48 49 50 4 5 6 1 2 2 2 2 2 2 6 6 6 5 5 96 97 98 99 6 1 2 3 3 3 3 3 4 3 3 3 46 47 48 49 50 5 5 5 6 6 3 3 3 3 3 1 6 5 4 3 96 97 98 99 1 2 2 2 2 2 2 2 5 4 3 2 Position Left Post Center Post Right Post Position Left Post Center Post Right Post Position Filter Center Post Position Right Post RECEPTACLE SHELL Left Post The last two digits in the DPX nomenclature (ex: DPXB-8-33B-0014) refer to the polarizing post position. When the last two digits are omitted it means the polarizing posts will not be assembled and position number is not stamped on the connector. This allows the customer to position the posts themselves and then stamp the appropriate number on the shell. If the last two digits are made 00 it means the polarizing posts are deleted. F Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com F-37 ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 38 MIL-C-81659 Rack and Panel Filter Connectors TDPX Table of Contents Single Gang TDPXB 2.000 (50.80) Two Holes .120 (3.05) Dia. Mfg. Ref. Only 2.000 (50.80) L* 1.612 + _ .005 (4.94 + _ 0.13) .766 (19.46) .125 (3.18) .720 + _ .005 (18.29 + _ 0.13) .225 (5.72) Max. Two Holes .120 (3.05) Dia. for Mfg. Ref. Only L* 1.750 + _ .005 (44.45 + _ 0.13) .120 (3.05) Dia. 4 Mfg. Holes .060 (1.52) 135 typ. .125 (3.18) .225 (5.72) Max. .720 + _ .005 (18.26 + _ 0.13) .988 + _ .005 (25.09 + _ 0.13) 2.047 (51.99) 3 Polarizing Posts 1.437 + _ .005 (36.50 + _ 0.13) 1.405 (35.69) 2.012 (51.10) 1.720 + _ .005 (43.69 + _ 0.13) .120 (3.05) Dia. and C' Sunk 82˚x.230 (5.84) Dia. 4 Holes 3 Polarizing Posts .719 + _ .005 (18.26 + _ 0.13) .719 + _ .005 (18.26 + _ 0.13) 1.720 + _ .005 (43.45 + _ 0.13) 1.437 + _ .005 (36.50 + _ 0.13) 33 ARINC B Shell 34 ARINC B Shell * This length varies between the limits of 1.750 (44.45) and 1.437 (36.25) depending on the particular construction as determined by contact arrangement. TDPXD 2.312 (58.72) 1.750 + _ 0.16 (44.45 + _ 0.15) 1.125 + _ .015 (28.58 + _ 0.38) 1.754 (44.55) Max. .120 (3.05) Dia. 4 Mfg. Holes .225 (5.72) Max. solder pot extentsion .750 + _ .005 (19.05 + _ 0.13) .188 (4.78)R Typ. 2.062 + _ .006 (52.37 + _ 0.15) .125 (3.18)R Typ. .344 (8.74) .125 (3.18) DPXA Shell Style Two Gang TDPX2 Two Holes .120 (3.05) Dia. for Mfg. Ref. Only L* .120 (3.05) Dia. anc C' Sunk 82˚x.230 (5.84) Dia. 4 Holes Two Holes .120 (3.05) Dia. for Mfg Ref. Only .766 (19.46) TOP .125 (3.18) .225 (5.72) Max. .125 (3.18) .225 (5.72) Max. 3.075 (78.11) 3 Polarizing Posts 2.331 + _ .005 (59.21 + _ 0.13) .060 (1.52) .188 (4.78) R Typ. TOP 2.783 + _ .005 (70.69 + _ 0.13) 3 Polarizing Posts L* 1.750 + _ .005 2.783 + _ .005 (70.69 + _ 0.13) 2.468 + _ .005 (62.69 + _ 0.13) 3.110 Filter .719 + _ .005 (18.26 + _ 0.13) 1.437 + _ .005 (36.50 + _ 0.13) .720 + _ .005 (18.29 + _ .013) .188 (4.78)R 2.00 (50.80) .988 + _ .005 (25.10 + _ 0.13) .719 + _ .005 (18.26 + _ 0.13) 1.437 + _ .005 (36.50 + _ 0.13) 1.612 + _ .005 (40.94 + _ 0.13) 33B ARINC B Shell .720 + _ .005 (18.29 + _ 0.13) 4 Mfg. Holes .120 (3.05) Dia. for #4-40 Screws 2.000 (50.80) 34B ARINC B Shell * This length varies between the limits of 1.750 (44.45) and 1.437 (36.25) depending on the particular construction as determined by contact arrangement. F Dimensions shown in inches (mm) Specifications and dimensions subject to change F-38 www.ittcannon.com ca_F1-F45.qxd:Layout 1 2/10/11 8:08 AM Page 39 MIL-C-81659 Rack and Panel Filter Connectors TDPX Table of Contents Three Gang TDPX3 L* 2.000 (50.80) .766 (19.46) L* 2.000 (50.80) 1.612 (40.94) .225 (5-72) Max. .060 (1.52) 1.750 (44.45) 4.354 (110.59) 4.318 (109.68) 4.026 (102.26) 4.026 (102.26) .225 (5.72) Max. solder pot extension 3.711 (94.26) .988 (25.10) .282 .180 (4.57)R. Typ. .718 (18.24) 1.437 (36.50) .125 (3.18) .282 (7.16) .718 (18.24) 1.437 (36.50) 6 MTG HOLES .120 (3.05) DIA. 33 Shell .125 (3.18) 34 Shell * This length varies between the limits of 1.750 an 1.437 depending upon particular construction as determined by contact arrangement. Four Gang TDPX4 L* 3.860 (98.04) .766 (19.46) L* 3.860 (98.04) .225 (5.72) Max. 1.612 (40.94) .060 (1.52) 3.610 (91.69) 2.468 (62.69) 2.783 (70.69) 3.110 (78.99) 3.110 (78.99) 2.783 (70.69) .988 (25.10) .930 (23.62) 1.648 (41.86) .225 (5.72) Max. .180 (457(R Typ. .125 (3.18) 10 Mtg. Holes .120 (3.05) Dia. .282 (7.16) .930 (23.62) 1.648 (41.86) 33 Shell .282 (7.16) .125 (3.18) 34 Shell * This length varies between the limits of 44.45 an 36.25 depending upon particular construction as determined by contact arrangement. Panel Cutouts - Page 40. Filter F Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com F-39