HA17558 Series Dual Operational Amplifier REJ03D0682-0100 (Previous: ADE-204-042) Rev.1.00 Jun 15, 2005 Description HA17558 is dual operational amplifiers which provides internal frequency compensation and high performance. It can be applied widely to measuring control equipment and to general Use. The two amplifiers share a common bias network and power supply leads. Features • High voltage Gain: 104dB (Typ) • High speed: 1V/µs • Continuous short-circuit protection • Low-noise operational amplifiers • Internal frequency compensation Ordering Information Type No. Application Package Code (Previous Code) HA17558FP HA17558F Industrial use Commercial use PRSP0008DE-B (FP-8DGV) PRSP0008DE-B (FP-8DGV) HA17558 HA17558PS Commercial use Industrial use PRDP0008AF-A (DP-8B) PRDP0008AF-A (DP-8B) Rev.1.00 Jun 15, 2005 page 1 of 12 HA17558 Series Pin Arrangement Vout1 1 8 VCC 7 Vout2 6 Vin(–)2 5 Vin(+)2 1 Vin(–)1 2 Vin(+)1 3 VEE 4 – + 2 + – (Top View) Circuit Schematic (1/2) VCC Vin(+) Vin(−) Vout to VCC VEE Rev.1.00 Jun 15, 2005 page 2 of 12 HA17558 Series Absolute Maximum Ratings (Ta = 25°C) Item Symbol Ratings HA17558 HA17558PS HA17558F HA17558FP Unit Supply voltage VCC VEE +18 –18 +18 –18 +18 –18 +18 –18 V V Differential input voltage Common-mode input voltage VIN (diff) 3 VCM* ±30 ±15 ±30 ±15 ±30 ±15 ±30 ±15 V V Power dissipation Operating temperature PT Topr 1 670* –20 to +75 1 2 670* –20 to +75 385* –20 to +75 2 385* –20 to +75 mW –20 to +75 Storage temperature Tstg –55 to +125 –55 to +125 –55 to +125 –55 to +125 °C Notes: 1. These are the allowable values up to Ta = 45 °C. Derate by 8.3mW/°C above that temperature. 2. These are the allowable values up to Ta = 31 °C mounting on 30% wiring density glass epoxy board. Derate by 7.14mW/°C above that temperature. 3. If the supply voltage is less than ±15V, input voltage should be less than supply voltage. Electrical Characteristics (Ta = 25°C, VCC = +15V, VEE = –15V) Item Symbol Min Typ Max Unit Test conditions Input offset voltage Input offset current VIO IIO — — 0.5 5 6 200 mV nA Input bias current Voltage gain IIB AVD — 86 50 104 500 — nA dB RL ≥ 2kΩ, VO = ±10V Maximum output voltage Maximum output voltage Vop-p Vop-p ±12 ±10 ±14 ±12.4 — — V V RL ≥ 10kΩ RL ≥ 2kΩ Common mode input voltage range Common mode rejection ratio VCM CMR ±12 70 ±14 100 — — V dB RS ≤ 10kΩ Supply voltage rejection ratio Power dissipation PSRR Pd — — 10 90 150 170 µV/V mW RS ≤ 10kΩ 2-channel, No load Slew rate Equivalent input noise voltage SR VNI — — 1.0 6 — — V/µs µVp-p AVD = 1 RS = 1kΩ, f = 1HZ to 1kHZ Channel separation CS — 105 — dB Rev.1.00 Jun 15, 2005 page 3 of 12 RS ≤ 10kΩ f = 1kHz HA17558 Series Characteristic Curves Maximum Output Voltage vs. Frequency VCC = 15 V VEE = –15 V RL = 2 kΩ 100 80 60 40 20 0 1 10 100 1 k 10 k 100 k 1 M 10 M Frequency f (Hz) Maximum Output Voltage VOP-P (V) 120 36 VCC = 15 V VEE = –15 V RL = 2 kΩ 32 28 24 20 16 12 8 4 0 100 Power Supply Rejection Ratio vs. Ambient Temperature 120 1M 130 VCC = 15 V VEE = –15 V VCC = 15 V VEE = –15 V 110 100 90 80 70 –20 1k 10 k 100 k Frequency f (Hz) Voltage Gain vs. Ambient Temperature Voltage Gain AVD (dB) Power Supply Rejection Ratio PSRR (dB) Open Loop Voltage Gain AV(OL) (dB) Open Loop Voltage Gain vs. Frequency 0 20 40 60 Ambient Temperature Ta (°C) Rev.1.00 Jun 15, 2005 page 4 of 12 80 120 110 100 90 80 –20 0 20 40 60 Ambient Temperature Ta (°C) 80 HA17558 Series Power Supply Rejection Ratio PSRR (dB) Power Supply Rejection Ratio vs. Frequency 120 VCC = 15 V VEE = −15 V 100 80 60 40 20 0 100 300 1k 3k 10 k 30 k Frequency f (Hz) 100 k 300 k 1M Common−mode Rejection Ratio CMR (dB) Common-mode Rejection Ratio vs. Frequency 120 VCC = 15 V VEE = −15 V Ta = 25°C RL = ∞ 100 80 60 40 20 0 100 Rev.1.00 Jun 15, 2005 page 5 of 12 300 1k 3k 10 k 30 k Frequency f (Hz) 100 k 300 k 1M HA17558 Series Maximum Output Voltage vs. Ambient Temperature Output Voltage VO (V) 10 Maximum Output Voltage VOP-P (VP-P) Transient Response VCC = 15 V VEE = −15 V 5 0 −5 −10 0 10 20 30 40 Time t (µs) Maximum Output Voltage VOP-P (VP-P) Power Dissipation Pd (mW) VCC = 15 V VEE = −15 V RL = ∞ 90 80 70 60 50 −20 0 20 40 60 Ambient Temperature Ta (°C) Rev.1.00 Jun 15, 2005 page 6 of 12 80 VCC = 15 V VEE = −15 V RL = 2 kΩ 32 24 16 8 0 −20 60 0 20 40 Ambient Temperature Ta (°C) 80 Maximum Output Voltage vs. Load Resistance Power Dissipation vs. Ambient Temperature 100 40 30 25 VCC = 15 V VEE = −15 V f = 1 kHz 20 15 10 5 100 200 500 1k 2k Load Resistance RL (Ω) 5k 10 k HA17558 Series Common-mode Input Voltage vs. Supply Voltage Supply Current vs. Supply Voltage 20 Supply Current ICC (mA) RL = ∞ 4 3 2 1 0 ±4 ±6 ±9 ±12 ±15 ±18 Common-mode Input Voltage VCM (V) 5 10 0 –10 –20 ±4 Supply Voltage VCC, VEE (V) ±8 ±12 ±16 Supply Voltage VCC, VEE (V) ±18 Input Bias Current vs. Ambient Temperature VCC = 15 V VEE = –15 V Slew Rate vs. Supply Voltage 1.2 80 Slew Rate SR (V/µs) Input Bias Current IIB (nA) 100 60 40 20 0 –20 1.0 0.8 0.6 0.4 ±4 0 20 40 60 Ambient Temperature Ta (°C) Rev.1.00 Jun 15, 2005 page 7 of 12 80 f = 1 kHz RL = 2 kΩ CL = 100 pF Ta = 25°C AV = 1 ±6 ±9 ±12 ±15 Supply Voltage VCC, VEE (V) ±18 HA17558 Series Input Offset Current vs. Ambient Temperature Input Offset Voltage vs. Supply Voltage VCC = 15 V VEE = –15 V Input Offset Voltage VIO (mV) Input Offset Current IIO (nA) 40 20 0 –20 –40 –20 0 20 40 60 Ambient Temperature Ta (°C) 80 4 2 0 –2 –4 –4 –6 –9 –12 –15 Supply Voltage VCC, VEE (V) –18 Slew Rate vs. Ambient Temperature 1.4 Voltage Gain vs. Supply Voltage Slew Rate SR (V/µs) Voltage Gain AVD (dB) 120 100 f = 10 Hz RL = 2 kΩ 80 60 1.2 VCC = 15 V VEE = –15 V RL = 2 kΩ CL = 100 pF AV = 1 1.0 0.8 0.6 40 –4 –6 –9 –12 –15 Supply Voltage VCC, VEE (V) Rev.1.00 Jun 15, 2005 page 8 of 12 –18 0.4 –20 0 20 40 60 Ambient Temperature Ta (°C) 80 HA17558 Series Output Short Current vs. Ambient Temperature Output Short Current IOS (mA) 60 VCC = 15 V VEE = –15 V 50 Sink 40 30 Source 20 10 –20 0 20 40 60 Ambient Temperature Ta (°C) 80 Input Noise Voltage vs. Frequency Input Noise Voltage VNI (nV/√ Hz) 100 RS = 100 Ω 30 10 3 1 10 Rev.1.00 Jun 15, 2005 page 9 of 12 30 100 300 1k Frequency f (Hz) 3k 10 k HA17558 Series Common-mode Rejection Ratio vs. Ambient Temperature VCC = 15 V VEE = –15 V 4 2 0 –2 –4 –20 0 20 40 60 Ambient Temperature Ta (°C) Rev.1.00 Jun 15, 2005 page 10 of 12 80 Common-mode Rejection Ratio CMR (dB) Input Offset Voltage VIO (mA) Input Offset Voltage vs. Ambient Temperature 140 VCC = 15 V VEE = –15 V 120 100 80 60 40 –20 0 20 40 60 Ambient Temperature Ta (°C) 80 HA17558 Series Circuit Example RIAA Pre-amplifier 0.0022 µF 0.01 µF +15 V + 100 µF – 36 kΩ 390 kΩ 33 µF – Input 2.2 kΩ 33 µF Otuput HA17558 + 10 kΩ + 47 µF – 56 kΩ – 100 µF + 1 kΩ –15 V T.H.D. vs. Output Voltage (RIAA Pre-Amp) T.H.D. vs. Output Voltage (RIAA Pre–Amp) 60 1.0 VCC = 15 V VEE = –15 V 50 T.H.D (%) 0.1 20 kHz 0.03 10 kHz 0.01 1 kHz 40 30 20 10 0.003 0.001 0.01 Voltage Gain AVD (dB) 0.3 20 kHz 0.03 0.1 0.3 1.0 Output Voltage (Vrms) Rev.1.00 Jun 15, 2005 page 11 of 12 3 10 0 10 30 100 300 1k 3k 10 k Frequency f (Vrms) 30 k 100 k HA17558 Series Package Dimensions JEITA Package Code P-DIP8-6.3x9.6-2.54 RENESAS Code PRDP0008AF-A Previous Code DP-8B MASS[Typ.] 0.51g D 5 E 8 1 4 b3 0.89 Z Reference Symbol Dimension in Millimeters Min Nom 7.62 D 9.6 E 6.3 Max A1 A e1 L A1 0.5 bp 0.38 θ c e1 0.48 c 0.20 θ 0° e 2.29 0.25 0.35 2.54 2.79 15° 1.27 Z 2.54 L JEITA Package Code P-SOP8-4.4x4.85-1.27 RENESAS Code PRSP0008DE-B *1 Previous Code FP-8DGV MASS[Typ.] 0.1g F D 8 0.58 1.3 b3 bp 7.4 5.06 A e 10.6 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Reference Symbol Terminal cross section ( Ni/Pd/Au plating ) Z e Min Nom Max 4.85 5.25 E 4.4 A2 4 1 Dimension in Millimeters D Index mark *3 bp A1 x M 0.00 0.1 0.35 0.4 0.45 0.15 0.20 0.25 6.5 6.75 A 2.03 bp L1 0.20 b1 c A c1 A1 θ L y Detail F θ 0° HE 6.35 e 1.27 x 0.12 y 0.15 0.75 Z L L Rev.1.00 Jun 15, 2005 page 12 of 12 8° 0.42 1 0.60 1.05 0.85 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 © 2005. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon 2.0