www.make-ps.com E-mail:[email protected] 100VFI series Single & Dual Output DC/DC Converter FEATURES • • • • • • HIGH ISOLATION - 6000 VDC Up to 75 % Efficiency Single and Dual Output, 1.5 watt converter Available in 5, 12, and 15 VDC Inputs Short Circuit Protection Low Isolation Capacitance DESCRIPTIONS INPUT CHARACTERISTICS The 100VFI Model 1.5 watt DC/DC’s are specially designed to provide ultra-high levels of isolation 6000VDC in a low profile 24 pin DIP package. The series consists of 18 models with input voltages of 5V, 12V and 15V, and offers regulated output voltages of 5V, 12V, 15V, ±5V, ±12V and ±15V. Min Input Voltage 5 VDC Input Models 4.5 12 VDC Input Models 10.8 15 VDC Input Models 13.5 Input Fuse Requirements 5 VDC Input Models 12 VDC Input Models 15 VDC Input Models Reverse Polarity Input Current Short Circuit Input Power Input Filter The 100VFI series is an excellent selection for railroad/ transportation equipment, medical equipment subsystems, process/machine control equipment and automatic test instrumentation. Typ Max Unit/Comments 5 12 15 1000 250 250 5.5 13.2 16.5 VDC VDC VDC mA; Slow blow type mA; Slow blow type mA; Slow blow type 0.5 Amp 1000 mW Pi Filter OUTPUT CHARACTERISTICS Min Typ Max Unit/Comments ±2.0 ±4.0 % Output voltage at nominal line & FL Output Voltage Balance ±0.5 ±2.0 % Equal Output (Duals) Loads Line Regulation ±1.2 ±1.5 %; % Change / Percentage change in Input voltage Load Regulation (5 Vout) ±7.0 ±10.0 % Output voltage measured from FL to 20% load Load Regulation (±5 Vout) ±8.0 ±12.0 Load Regulation (12,±12 Vout) ±6.0 ±8.0 Load Regulation (15,±15 Vout) ±4.0 ±6.0 Ripple/Noise 30 40 mV p-p, Nom.Line @FL, 20MHz B.W., using 1 μf bypass capacitor Ripple/Noise 50 mV p-p, Over Line, Load & Temp., 20 MHz B.W., using 1 μf bypass capacitor Overload Protection %Rated Output Load 120 Short Circuit Protection Continuous, Automatic Recovery Temperature Coefficient ±0.01 ±0.02 % per degree C Output Voltage Set Point GENERAL CHARACTERISTICS Switching Frequency Test Isolation Voltage Rated Isolation Voltage Isolation Resistance Isolation Capacitance MTBF (MIL-HBK-217F) Min Typ Max Unit/Comments kHz 50 100 VDC, 1 minute 8,000 VDC, 1 minute 6,000 Mohm, 500VDC 10,000 10 15 pF, 100kHz, 1Volt Million Hours, 2 +25oC, Ground Benign >> B-17 www.make-ps.com E-mail:[email protected] ENVIRONMENTAL SPECIFICATIONS Operating Temp. Range Storage Temp. Range Relative Humidity Min -40 -55 PHYSICAL CHARACTERISTICS Typ Max +85 +125 +95 Cooling Unit/Comments o C; Ambient o C % Humidity; noncondensing Free-Air Convection Unit/Comments 1.25 X 0.8 X 0.4 inches (31.8 X 20.3 X 10.2 mm) Non-Conductive Black Plastic UL94V-0 12 Grams Case Size Case Material Flammability Weight OUTLINE DRAWING 1.25 (31.8) 0.40 (10.2) SIDE VIEW 0.15 (3.8) 0.020(0.50) PIN DIA. 0.100 (2.54) 0.08 (2.0) 1 2 11 12 BOTTOM VIEW 24 23 0.10 (2.5) 0.600 0.80 (15.22) (20.3) 15 14 13 PIN OUT CHART Pins 1 2 11 12 13 14 15 23 24 Single + Vin + Vin + Vout + Vout - Vout - Vout No Pin - Vin - Vin Dual + Vin + Vin + Vout + Vout Common Common - Vout - Vin - Vin Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 X.XXX= ±0.010 X.XX = ±0.25 Pin : ±0.002 ±0.05 All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. >> B-18 www.make-ps.com E-mail:[email protected] HOW TO ORDER HOW TO ORDER 1 XX S XX VFI - Y ROHS Compliant Series Nominal Input Voltage Wattage=1.5W Output Voltage Output Configuration (S=Single, D=Dual) MODEL SELECTION CHART Model 105S5VFI 112S5VFI 115S5VFI 105D5VFI 112D5VFI 115D5VFI 105S12VFI 112S12VFI 115S12VFI 105D12VFI 112D12VFI 115D12VFI 105S15VFI 112S15VFI 115S15VFI 105D15VFI 112D15VFI 115D15VFI Nominal Input Voltage (VDC) 5 5 5 5 5 5 12 12 12 12 12 12 15 15 15 15 15 15 Output Voltage (VDC) 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 ±15 Full Load Output Current (mA) 300 125 100 ±150 ±63 ±50 300 125 100 ±150 ±63 ±50 300 125 100 ±150 ±63 ±50 No Load Input Current (mA) 50 50 50 50 50 50 30 30 30 30 30 30 30 30 30 30 30 30 Full Load Input Current (mA) 400 400 400 400 400 400 167 167 167 167 167 167 133 133 133 133 133 133 Reflected Ripple Current (mA) 30 30 30 30 30 30 25 25 25 25 25 25 20 20 20 20 20 20 Efficiency @ FL (%) 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 >> B-19 www.make-ps.com E-mail:[email protected] DERATING CURVES MODEL 100VFI Pout % 100 90 80 70 60 50 40 30 20 10 0 -40 100LFM 400LFM 200LFM Natural Convection 50 60 70 80 90 100 110 TEMPERATURE ° C >> B-20