lg-5630wkz-dt-1-p-crh Pdf - Ligitek Electronics Co. Ltd.

LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
0.4W Power Light LED
Pb
Lead-Free Parts
LG-5630WKZ-DT-1-P-CRH
DATA SHEET
DOC. NO : QW0905-LG-5630WKZ-DT-1-P-CRH
REV.
:
A
DATE
:
27 - Aug. - 2012
發行
立碁電子
DCC
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Product Model Designation System
LG - 56 30 WK Z - D T - 1 - P - CRH
A
A
Title
LG:Ligitek
F
Epoxy Color
D:Yellow Diffused
B
C
B
Dimension(L)
57:5.7mm
56:5.6mm
G
Package
T:Tape&Reel
D
E
F
G
C
H
I
D
Dimension(W)
Emitting Color
30:3.0mm
WK:White Color
J
E
Zener
H
I
J
Chip Modification
Patent
P: IP Free
Bin Modification
-X: 2 chip in 1(Parallel)
-1: 1 chip in 1
-2: 2 chip in 1(Series)
Page 1/14
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Typical Applications
Features
*. White colored SMTpackage
*.Suitable for all SMT assembly and soldering methodes
*. Pb-Free Reflow soldering application
*. More Energy Efficient than lncandescent and most Halogen lamps.
*. RoHS compliant
*. Reading Light (car,bus,aircraft)
*. Portable(flashlight,bicycle).
*. Backlights(Monitor,TV) / Light Guides.
*. Automotive Exterior (Stop-Tail-Tum,CHMSL,Mirror Side Repeat).
*. Commercial and Residential Architectural lighting.
*. Mini-accent / Uplighters / Downlighters / Orientation lighting
*. Fiber Optic Alternative / Decorative / Entertainment lighting.
*. Security / Garden lighting.
*. Cove / Undershelf / Task lighting.
*. Traffic signaling / Beacons / Rail crossing and Wayside lighting.
Dimension
5.3
C
3.0
A
C
Recommended Solder Patterns
5.6
2.0
0.9
1.6
1.62
3.8
6.8
0.5
0.8
1.28
0.5 2.1
Slug
Anode(+)
0.3 2.3
0.8
Cathode(-)
Note:
1.The tolerance unless mentioned is ±0.1mm,unit=mm.
2.The slug has polarity as anode.
3.It is strongly recommended to apply on electrically isolated
heat conducting film between the slug and contact surfaces.
Page 2/14
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Absolute Maximum Ratings at Ta=25℃
Ratings
Parameter
Symbol
UNIT
White
DC Forward Current
IF
150
mA
Power Dissipation
PD
0.5
W
Peak pulse current
Duty 1/10@10KHz
IFP
200
mA
LED junction Temperature
Tj
125
℃
Reverse Current(VR=5V)
Ir
10
μA
ESD Sensitivity
VB
±2000
V
Storage Temperature
Tstg
-40 ~ +100
°C
Operating Temperature
Topr
-40 ~ +85
°C
Soldering Temperature
Tp
260
°C
Note:
1.Proper current derating must be observed to maintain temperature below the maximum.
2.LEDS are not designed to be driven in reverse bias.
Luminous Intensity Characteristics at 120mA
(Ratings At 25°C Ambient)
Luminous Intensity
PART NO
Emission
Color
Min.
Typ.
Max.
LG-5630WKZ-DT-1-P-CRH
White
32
34
----
Note :
1. White emitters are built with InGaN.
2. Luminous Intensity is measured with an accuracy of ±10%
Page 3/14
Units
lm
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Forward Voltage Characteristics at 120mA
(Ratings At 25°C Ambient)
Vf
PART NO
Emission
Color
Min.
Typ.
Max.
LG-5630WKZ-DT-1-P-CRH
White
2.8
----
3.6
Units
V
Note : Forward Voltage is measured with an accuracy of±0.1V
Chromaticity Coordinates Characteristics at 120mA
(Ratings At 25¢J Ambient )
PART NO
Emission
Color
LG-5630WKZ-DT-1-P-CRH
White
Chromaticity Coordinates
Y
X
Max.
Max.
Min.
Min.
0.2470
0.2585
0.2065
0.2240
Note : ±0.01 is tester tolerance.
Emission Angle Characteristics at 120mA
(Ratings At 25°C Ambient )
PART NO
Emission
Color
Lambertian
Units
LG-5630WKZ-DT-1-P-CRH
White
120
Degrees
Page 4/14
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Bin Code Description
Bin Code
Luminous
Intensity
Forward
Voltage
CIE
Dominant Wave
Length
D7
G
e
2
Color Rank
@IF=120mA
Luminous Intensity
(lm)
@IF=120mA
Bin
Code
Data
code
Min.
Max.
D6
HI4
32
34
D7
HI6
34
36
D8
HI8
36
38
D9
HI0
38
40
D0
HJ2
40
42
Bin Code
Data code
e
m05
g
m07
Forward Voltage(V)
@IF=120mA
Bin
Code
Data
code
Range
G
DG
2.8-3.0
H
DH
3.0-3.2
J
DJ
3.2-3.4
K
DK
3.4-3.6
Page 5/14
Dominant Wave
Length
@IF=120mA
Bin
Code
Data
Code
Range(nm)
2
2
450~452.5
5
5
452.5~455
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Bins Code of chromaticity coordinates
CODE
m05
m07
1
X
0.2585
0.2520
2
Y
0.2175
0.2065
X
0.2535
0.2470
3
Y
0.2240
0.2130
NOTE: Tolerance on each color bin(x,y)is±0.01
Page 6/14
X
0.2600
0.2535
4
Y
0.2350
0.2240
X
0.2650
0.2585
Y
0.2285
0.2175
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
The C.I.E 1931 Chromaticity Coordinates
0.27
0.26
m13
0.25
m01
m14
0.24
m03
m04
m15
0.23
m116
0.22
m08
m09
m18
0.20
m05
m06
m07
m17
0.21
m02
m10
m11
0.19
m12
0.18
0.17
0.22
0.23
0.24
0.25
0.26
Page 7/14
0.27
0.28
0.29
0.30
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Recommended Profile for Reflow Soldering
Pb -free solder temperature profile
Pb -free solder Temperature profile
Pre-heat
Pre-heat time
Peak-Temperature
Soldering time condition
180-200°C
120 Sec Max
260°C Max
10 Sec Max
260°C.Max.
10 Sec .Max.
1-5°C/Sec.
60 Sec.Max.
Above220°C
6°C/Sec.
Pre-heating
180-200°C
1-5°C/Sec.
120 Sec. Max.
(1) Reflow soldering should not be done more than two times.
(2) When soldering,do not put stress on the LEDs during heating.
(3) After soldering,do not warp the circuit board.
(4) The encapsulated material of the LEDs is silicone.
Precautions should be taken to avoid the strong pressure on the encapsulated part.
So when using the chip mounter,the picking up nozzle that does not affect the
silicone resin should be used.
Hand Soldering Conditions:
Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only)
Page 8/14
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Typical Electro Optical Characteristics Curves
Fig.3 Max. Driving Forward Current VS. Soldering Temperature
200
140
Forward Current(mA)
Forward Current(mA)
Fig.1 Forward current vs. Forward Voltage
120
100
80
60
40
20
0
2.6
2.8
3
3.2
3.4
150
100
50
0
3.6
0
20
Forward Voltage(V)
60
80
100
Soldering Temperature T s (°C)
Fig.4 Directivity Radiation
Fig.2 Forward current vs.Luminous Intensity
0°
1.2
-30°
1
30°
0.8
0.6
-60°
0.4
60
0.2
0
0
20
40
60
80
100
120
140
Forward Current(mA)
100% 75% 50% 25%
0
25% 50% 75% 100%
Fig.5 Luminous Spectrum(Ta=25 °C)
Relative Luminous Flux(%)
Relative Luminous Intensity(%)
40
SPECTRAL RADIANCE
70
60
50
40
30
20
10
0
300
350
400
450
500
550
600
650
700
Wavelength (nm)
Page 9/14
750
800
850
900
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Carrier Type Dimensions
Loaded quantity 2000 PCS per reel
4.0
0.25
1.5
1.75
-
5.5
+
12.0±0.3
5.95
9.3
Polarity
4.0
3.25
1.2
Note : The tolerances unless mentioned is ±0.2mm.
Packing Specifications
Label
Aluminum Moist-Proof bag
Label
Desiccant
Page 10/14
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Label Explanation
芯瑞達科(香港)有限公司
CRH COREACH
TECHNOLOGY(HK)Co.,Ltd.
ROHS
P/N:CRH-B5630BW1-J4T02-LG1
Q.C.
BIN:D7Ge5
See Bin Code Description
Q'TY: 2000 PCS
Date:2012/08/23
批號 :HI6DGm075 GS11280183
Reel Dimensions
16.0±1.0
60.2±0.5
Page 11/14
178±1
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Box Explanation
1. 4 BAG / INNER BOX
2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm
H
W
L
3. 10 INNER BOXES / CARTON
4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm
W
L
H
Page 12/14
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Reliability Test
(1)Test items and results
Test Item
Classification
Test Condition
Sample
Size
Operating Life Test
1.Ta=Under Room Temperature As Per Data Sheet
Maximum Rating.
2.If=120mA
3.t=1000 hrs
22
High Temperature
Storage Test
1.Ta=100℃
2.t=1000 hrs
22
Low Temperature
Storage Test
1.Ta=-40℃
2.t=1000 hrs
22
High Temperature
High Humidity
Storage Test
1.Ta= 85℃
2.RH=85 %
3.t=1000 hrs
22
Endurance
Test
Thermal Shock Test
Environmental
Test
Reflow Soldering Test
Temperature
Cycling
1.Ta=-40 ℃(30min) -100 ℃(30min)
2.total 100 cycles
22
1.T.Sol=260℃±5℃
2.Dwell Time= 10 Sec.Max.
22
1.100℃ ~ 25℃ ~ -40℃
30mins 5mins 30mins
2.100 Cyeles
22
(2)Criteria for judging the damage
Item
Symbol Test Conditions
Criteria for Judgement
Min.
Max.
Forward Voltage
Vf
If=120mA
-
U.S.L x1.2
Reverse Current
Ir
Vr=5V
-
U.S.L x2.0
Luminous Intensity
Iv
If=120mA
L.S.L x 0.5
-
Note:
1.U.S.L.:Upper Standard Level.
2.L.S.L.:Lower Standard Level.
Page 13/14
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Precautions For Use:
Storage time:
1.The operation of Temperatures and RH are : 5℃~35℃,RH60%.
2.Once the package is opened, the products should be used within a week.
Otherwise, they should be kept in a damp proof box with descanting agent.
Considering the tape life, we suggest our customers to use our products within
a year(from production date).
3.If opened more than one week in an atmosphere 5℃ ~ 35℃,RH60%,
they should be treated at 60 ℃±5 ℃for 15hrs.
Drive Method:
LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into
the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series
with the LED.
Consider worst case voltage variations than could occur across the current limiting resistor. The forward
current should not be allowed to change by more than 40% of its desired value.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED.
Cleaning:
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED.
ESD(Electrostatic Discharge):
Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic
glove is recommended when handing these LED. All devices, equipment and machinery must be properly
grounded.
Page 14/14