LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 3W Power Light LED Pb Lead-Free Parts LGL2V-531E-HV140-LS/TR2-D01 DATA SHEET DOC. NO : QW0905-LGL2V-531E-HV140-LS/TR2-D01 REV. : A DATE : 06 - Sep. - 2011 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Applications Features *. Reading Light (car,bus,aircraft) *. Portable(flashlight,bicycle). *. Commercial and Residential Architectural lighting. *. Mini-accent / Uplighters / Downlighters / Orientation lighting *. Fiber Optic Alternative / Decorative / Entertainment lighting. *. Security / Garden lighting. *. Cove / Undershelf / Task lighting. *. Traffic signaling / Beacons / Rail crossing and Wayside lighting. *. Saving energy and cost reduction from power converter *. Energy loss in voltage transform from high to low *. voltage conversion from high to low is expensive *. AC DC drive available *. Easy adaption for existing dimming circuit *. Compact design *. Saving space for limited area (ex. candle light) *. Easier for package and optical design Dimension 7.4 5.0 1.6 1.6 1 6 2 5 3 4 Recommended Solder Patter 5.0 7.9 R1.5 1.0 1.0 3.25 1.3 1.2 0.4 0.2 1.2 0.4 1.2 3.75 1.0 2.2 4.2 Note : The tolerances unless mentioned is ±0.1mm,Unit=mm. 1 2 3 4 5 6 Note : 1.All dimension are in millimeter tolerance is ±0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. Page 1/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25°C Ratings Parameter Symbol UNIT White DC Forward Current IF 25 mA Peak pulse current Duty 1/10@10KHz IFP 60 mA Power Dissipation PD 3.8 W Reverse Current(VR=5V) Ir 50 μA ESD Sensitivity VB ±500 V Operating Temperature Topr -20 ~ +80 °C Storage Temperature Tstg -30 ~ +100 °C Note: 1.Proper current derating must be observed to maintain temperature below the maximum. 2.LEDS are not designed to be driven in reverse bias. Luminous Intensity Characteristics at 20mA (Ratings At 25°C Ambient) PART NO LGL2V-531E-HV140-LS/TR2-D01 Emission Color White Luminous Intensity @20mA Min. Typ. Max. 90 130 ---- Note : 1. White emitters are built with InGaN. 2. Luminous Intensity is measured with an accuracy of ±10% Page 2/14 Units lm LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage Characteristics at 20mA (Ratings At 25°C Ambient) PART NO Vf Emission Color Min. Typ. Max. White 128 ---- 152 LGL2V-531E-HV140-LS/TR2-D01 Units V Note : Forward Voltage is measured with an accuracy of±0.1V Chromaticity Coordinates Characteristics at 20mA (Ratings At 25°C Ambient) Chromaticity Coordinates PART NO Emission Color White LGL2V-531E-HV140-LS/TR2-D01 X Y Min. Max. Min. Max. 0.383 0.487 0.36 0.454 Note : ±0.01 is tester tolerance. Emission Angle Characteristics at 20mA (Ratings At 25°C Ambient) PART NO LGL2V-531E-HV140-LS/TR2-D01 Emission Color Lambertian Units White 120 Degess Color Rendering Index Characteristics at 20mA (Ratings At 25°C Ambient ) PART NO LGL2V-531E-HV140-LS/TR2-D01 CRI Emission Color Min. Typ. Max. White 80 ---- ---- Page 3/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bin Code Description Bin Code Luminous Intensity CIE Forward Voltage FA1FA2 NO 128-152 Luminous Intensity (lm) @IF=20mA Bin Code Min. Max. F90FA0 90 100 FA0FA1 100 110 FA1FA2 110 120 FA2FA3 120 130 FA3FA4 130 140 FA4FA5 140 150 FA5FA6 150 160 Color Rank @IF=20mA MM MN MO MP NM NN NO NP PM PN PO PP QM QN QO QP RM RN RO RP Page 4/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of chromaticity coordinates Color Coordiante at20mA CCT(K) 2670~2850 2850~3050 3050~3250 3250~3500 3500~3800 BIN CODE 1 3 2 4 X Y X Y X Y X Y MM 0.471 0.451 0.461 0.433 0.477 0.437 0.487 0.454 MN 0.461 0.433 0.453 0.416 0.467 0.420 0.477 0.437 MO 0.453 0.416 0.444 0.399 0.458 0.403 0.467 0.416 MP 0.458 0.403 0.444 0.399 0.436 0.384 0.449 0.338 NM 0.454 0.446 0.471 0.451 0.46 0.43 0.444 0.426 NN 0.444 0.426 0.46 0.43 0.453 0.416 0.438 0.412 NO 0.438 0.412 0.453 0.416 0.444 0.399 0.429 0.394 NP 0.429 0.394 0.444 0.399 0.436 0.384 0.422 0.379 PM 0.438 0.44 0.454 0.446 0.444 0.426 0.43 0.421 PN 0.43 0.421 0.444 0.426 0.438 0.412 0.424 0.407 PO 0.424 0.407 0.438 0.412 0.429 0.394 0.416 0.389 PP 0.416 0.389 0.429 0.394 0.422 0.379 0.41 0.374 QM 0.421 0.433 0.438 0.44 0.43 0.421 0.414 0.414 QN 0.414 0.414 0.43 0.421 0.424 0.407 0.409 0.4 QO 0.409 0.4 0.424 0.407 0.416 0.389 0.402 0.382 QP 0.402 0.382 0.416 0.389 0.41 0.374 0.396 0.367 RM 0.402 0.423 0.421 0.433 0.414 0.414 0.397 0.406 RN 0.397 0.406 0.414 0.414 0.409 0.4 0.392 0.391 RO 0.392 0.391 0.409 0.4 0.402 0.382 0.387 0.374 RP 0.387 0.374 0.402 0.382 0.396 0.367 0.383 0.36 NOTE: Tolerance on each color bin(x,y)is±0.01 Page 5/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only CIE Chromaticity Diagram 0.48 0.46 3050K 3500K 3800K 0.42 PM MN NN PN MO QN RN NO PO QO RO 0.38 NM QM RM 0.40 2670K MM 3250K 0.44 2850K NP MP PP QP RP 0.36 0.34 0.36 0.38 0.40 0.42 0.44 0.46 0.48 Page 6/14 0.50 0.52 0.54 0.56 0.58 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Recommended Profile for Reflow Soldering Pb -free solder temperature profile Pb -free solder Temperature profile Pre-heat Pre-heat time Peak-Temperature Soldering time condition 180-200°C 120 Sec Max 260°C Max 10 Sec Max 260°C.Max. 10 Sec .Max. 1-5°C/Sec. 60 Sec.Max. Above220°C 6°C/Sec. Pre-heating 180-200°C 1-5°C/Sec. 120 Sec. Max. (1) Reflow soldering should not be done more than two times. (2) When soldering,do not put stress on the LEDs during heating. (3) After soldering,do not warp the circuit board. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter,the picking up nozzle that does not affect the silicone resin should be used. Hand Soldering Conditions: Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only) Page 7/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.1 Forward current vs. Forward Voltage Forward Current(mA) 100 10 1 100.00 110.00 120.00 130.00 140.00 150.00 160.00 170.00 Forward Voltage(V) Relative Luminous Flux(%) Fig.2 Forward current vs. Luminous Intensity 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 5 10 15 20 25 If-Forward Current [mA] Page 8/14 30 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Relative Luminous Flux(%) Fig.3 Luminous Spectrum(Ta=25 ℃) SPECTRAL RADIANCE 100 80 60 40 20 0 400 500 600 700 800 Wavelength (nm) Fig.4 Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 Page 9/14 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.5 Thermal Design Maximum Current (mA) 40 30 20 10 0 0 20 40 60 80 100 120 Ambient Temperature (ºC) Relative Intensity [%] Fig.6 Relativa lntensity @ vs Ambient Temperature 120 100 80 60 40 20 0 20 40 60 Ta[°C] Page 10/14 80 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Carrier Type Dimensions 4.0 8.0 2.0 ψ1.5 0.3 1.75 7.5 16 7 + 13.3 Polarity 5.3 3.4 Note : The tolerances unless mentioned is ±0.2mm. Packing Specifications Label Aluminum Moist-Proof bag Label Desiccant Page 11/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. PART : LGL2V-531E-HV140-LS/TR2-D01 LOT : GS1-110315 QTY(PCS): 1000 BIN/HUE : FA1FA2/NO BIN : Luminous Intensity HUE : Chromaticity Coordinates (CIE_x , CIE_y) VF : Forward Voltage VF:128-152 Reel Dimensions 20.7±1.0 13.5±1.0 330±2.0 99±2.0 16.7±1.0 Page 12/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Box Explanation 1. 3 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 36cm X 10cm x 36cm L W H 3. 2 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 41.5cm X 26cm x42.5cm L W H Page 13/14 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Reliability Test Stress Condition Item Description RTOL Room Temperature Operation Life 25°C,Max If 1000 hours WHT Wet High Temperature 85°C/85%RH 1000 hours TC Temperature Cycling 200 cycles TS Thermal Shorck -40/+110°C, 30min dwell,<5min trans. -40/+110°C, 20min dwell,<20min trans. HTSL Hight Temperature Storage Life 120°C 1000 hours LTSL Low Temperature Storage Life -40°C 1000 hours SHR Solder Heat Resistance 260±5°C,5secs MS Mechanical Shock 1500G,0.5msec pulse, 5 shocks each 6 axis ND Natural Drop On concrete from 1.2m, 3xtimes RV Random Vibration 6G RMS from 10 to 2KHz, 10mins/axis VVF Variable Vibration Frequency 10-2000-10Hz, 20G 1min, 1.5mm, 3timesx/axis Test Duration 200 cycles Operating Life Test 106.0% 336 104.0% y = e -2E-05x Decay 102.0% 500 0 100.0% 168 98.0% 668 842 96.0% 94.0% 92.0% 90.0% 0 100 200 300 400 500 600 T(hr) Note: Failuer Criteria: Electrical failures VF shift >=10% IR < 50 uA@Vr = 5v Ligitek output Degradation %Iv shift >=30%@1000hrs or 200cycle Broken or damaged pockage or lead Dimension out of tolerance Page 14/14 700 800 900 1000