LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 0.2W Power Light LED Pb Lead-Free Parts LG-5630WK-1-T60-P-X-DXXX DATA SHEET DOC. NO : QW0905-LG-5630WK-1-T60-P-X-DXXX REV. : A DATE : 18 - Jun. - 2012 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product Model Designation System LG - 56 30 WK Z - 1 - T60 - P - C - D8 01 A B A Title LG:Ligitek F C D B Dimension(L) E F C G H I Emitting Color 57:5.7mm 56:5.6mm 30:3.0mm WK:White Color G H Test Current -X: 2 chip in 1(Parallel) T60: 60mA Patent P: IP Free -1: 1 chip in 1 -2: 2 chip in 1(Series) K Bin Modification Page 1/16 K D Dimension(W) Chip Modification J E Zener J I Chromaticity Coordinates CRI -CW: Cool White -NW: Neutral White -WW: Warm White Characteristics D7 : CRI>70 D8 : CRI>80 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Applications Features *. White colored SMTpackage *.Suitable for all SMT assembly and soldering methodes *. Pb-Free Reflow soldering application *. More Energy Efficient than lncandescent and most Halogen lamps. *. RoHS compliant *. Reading Light (car,bus,aircraft) *. Portable(flashlight,bicycle). *. Backlights(Monitor,TV) / Light Guides. *. Automotive Exterior (Stop-Tail-Tum,CHMSL,Mirror Side Repeat). *. Commercial and Residential Architectural lighting. *. Mini-accent / Uplighters / Downlighters / Orientation lighting *. Fiber Optic Alternative / Decorative / Entertainment lighting. *. Security / Garden lighting. *. Cove / Undershelf / Task lighting. *. Traffic signaling / Beacons / Rail crossing and Wayside lighting. Dimension 5.3 C A 3.0 C Recommended Solder Patterns 5.6 2.0 0.9 1.6 1.62 3.8 6.8 0.5 0.8 1.28 0.5 2.1 Slug Anode(+) 0.3 2.3 0.8 Cathode(-) Note: 1.The tolerance unless mentioned is ±0.1mm,unit=mm. 2.It is strongly recommended to apply on electrically isolated heat conducting film between the slug and contact surfaces. Page 2/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25℃ Ratings Parameter Symbol UNIT White DC Forward Current IF 60 mA Power Dissipation PD 0.22 W Peak pulse current Duty 1/10@10KHz IFP 100 mA LED junction Temperature Tj 125 ℃ Reverse Current(VR=5V) Ir 10 μA ESD Sensitivity VB ±500 V Storage Temperature Tstg -40 ~ +100 °C Operating Temperature Topr -40 ~ +85 °C Soldering Temperature Tp 260 °C Note: 1.Proper current derating must be observed to maintain temperature below the maximum. 2.LEDS are not designed to be driven in reverse bias. Device Selection Guide: Part No. MATERIAL LG-5630WK-1-T60-P-X-DXXX InGaN/GaN Page 3/16 COLOR Emitted Cool White Warm White Lens Yellow Diffused LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Luminous Intensity Characteristics at 60mA (Ratings At 25°C Ambient) Luminous Intensity Part No. Emission Color Min. Typ. Max. LG-5630WK-1-T60-P-X-DXXX White 14 ---- 30 Units lm Note : 1. White emitters are built with InGaN. 2. Luminous Intensity is measured with an accuracy of ±10% Forward Voltage Characteristics at 60mA (Ratings At 25°C Ambient) Vf Part No. Emission Color Min. Typ. Max. LG-5630WK-1-T60-P-X-DXXX White 2.8 ---- 3.6 Units V Note : Forward Voltage is measured with an accuracy of±0.1V Chromaticity Coordinates Characteristics at 60mA (Ratings At 25°C Ambient ) Part No. Emission Color LG-5630WK-1-T60-P-X-DXXX White Chromaticity Coordinates X Y Max. Max. Min. Min. 0.3028 0.4813 0.3113 0.4319 Note : Chromaticity Coordinates is measured with an accuracy of±0.01. Emission Angle Characteristics at 60mA (Ratings At 25°C Ambient ) Part No. Emission Color Lambertian Units LG-5630WK-DT-1-T60-X-XX-XXX White 120 Degrees Page 4/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product List Part No. CCT(K) CRI Luminous Intensity(lm) Min. Max. Min. Min. Typ. Max. LG-5630WK-1-T60-P-C-D812 5310 6500 80 16 18 ---- LG-5630WK-1-T60-P-W-D813 2580 2870 80 14 16 ---- Note : CRI is measured with an accuracy of±2.0. Page 5/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bin Code Description Bin Code Luminous Intensity CIE Forward Voltage F20D WO 3.0-3.1 Luminous Intensity (lm) @IF=60mA Bin Code Min. Max. F14D 14 16 F16D 16 18 F18D 18 20 F20D 20 22 F22D 22 24 F24D 24 26 F26D 26 28 F28D 28 30 Color Rank @IF=60mA Forward Voltage(V) @IF=60mA CW WW 65K-1 27K-1 2.8-2.9 65K-2 27K-2 2.9-3.0 57K-1 27K-3 3.0-3.1 57K-2 27K-4 3.1-3.2 57K-3 3.2-3.3 57K-4 3.3-3.4 3.4-3.5 3.5-3.6 Page 6/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of CW chromaticity coordinates CCT(K) Reference Range 6020-6500 5310-5700 5700-6020 1 BIN CODE X 2 Y X 3 Y X 4 Y X Y 65K-1 0.3205 0.3481 0.3117 0.3393 0.3131 0.3290 0.3213 0.3371 65K-2 0.3213 0.3371 0.3131 0.3290 0.3145 0.3187 0.3221 0.3261 57K-1 0.3376 0.3616 0.3292 0.3539 0.3293 0.3423 0.3371 0.3493 57K-2 0.3371 0.3493 0.3293 0.3423 0.3294 0.3306 0.3366 0.3369 57K-3 0.3292 0.3539 0.3207 0.3462 0.3215 0.3353 0.3293 0.3423 57K-4 0.3293 0.3423 0.3215 0.3353 0.3222 0.3243 0.3294 0.3306 0.38 5310 5700 0.36 6020 6500 0.34 57K-1 57K-3 57K-2 65K-1 57K-4 65K-2 0.32 0.30 0.30 0.32 0.34 Page 7/16 0.36 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of WW chromaticity coordinates CCT(K) Reference Range 2580-2725 2725-2870 BIN CODE 1 X 2 Y X 3 Y X 4 Y X Y 27K-1 0.4813 0.4319 0.4688 0.4290 0.4585 0.4104 0.4703 0.4132 27K-2 0.4703 0.4132 0.4585 0.4104 0.4483 0.3919 0.4593 0.3944 27K-3 0.4688 0.4290 0.4562 0.4260 0.4468 0.4077 0.4585 0.4104 27K-4 0.4585 0.4104 0.4468 0.4077 0.4373 0.3893 0.4483 0.3919 0.44 2870 2725 0.42 27K-3 0.40 27K-4 2580 27K-1 27K-2 0.38 0.36 0.38 0.40 0.42 0.44 Page 8/16 0.46 0.48 0.50 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Recommended Profile for Reflow Soldering Pb -free solder temperature profile Pb -free solder Temperature profile Pre-heat Pre-heat time Peak-Temperature Soldering time condition 180-200°C 120 Sec Max 260°C Max 10 Sec Max 260°C.Max. 10 Sec .Max. 1-5°C/Sec. 60 Sec.Max. Above220°C 6°C/Sec. Pre-heating 180-200°C 1-5°C/Sec. 120 Sec. Max. (1) Reflow soldering should not be done more than two times. (2) When soldering,do not put stress on the LEDs during heating. (3) After soldering,do not warp the circuit board. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter,the picking up nozzle that does not affect the silicone resin should be used. Hand Soldering Conditions: Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only) Page 9/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage(V) Fig.1 Forward current vs. Forward Voltage Forward Current(mA) Relative Luminous Intensity(%) Fig.2 Forward current vs.Luminous Intensity Forward Current(mA) Page 10/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.3 Luminous Spectrum(Ta=25°C) Relative Luminous Flux(%) SPECTRAL RADIANCE Wavelength (nm) Fig.4 Directivity Radiation 0° -30° 30° -60° 60° 100% 75% 50% 25% 0 Page 11/16 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Carrier Type Dimensions 4.0 0.25 1.5 1.75 - 5.5 + 12.0±0.3 5.9 9.3 Polarity 4.0 3.25 1.2 Note : The tolerances unless mentioned is ±0.2mm. Packing Specifications Label Aluminum Moist-Proof bag Label Desiccant Page 12/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. PART : LG-5630WK-1-T60-P-C-D801 LOT : GS1-060109 QTY(PCS): 2000 BIN/HUE : F20D/27K-1 BIN : Luminous Flux HUE : Chromaticity Coordinates (CIE_x , CIE_y) VF:3.1-3.2 3.1 - 3.2 : Forward Voltage Reel Dimensions 16.0±1.0 60.2±0.5 178±1 13.5 Page 13/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Box Explanation 1. 4 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm W L H Page 14/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Reliability Test: (1)Test items and results Test Item Classification Test Condition Sample Size Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=60mA 3.t=1000 hrs 22 High Temperature Storage Test 1.Ta=105 ℃± 5℃ 2.t=500 hrs 22 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs 22 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta=85℃± 5℃ 3.RH=90 %~95% 4.t=500hrs±2hrs 22 Thermal Shock Test 1.IR-Reflow In-Board,2 times 2.Ta=105 ℃ ±5℃ & -40℃± 5℃ (30min) (30min) 3.total 100 cycles 22 1.T.Sol=260 ℃±5℃ 2.Dwell Time= 10Max. 22 1.105℃ ~ 25℃ ~ - 40℃ 30mins 15mins 30mins 2.100 Cyeles 22 Endurance Test Environmental Test Reflow Soldering Test Temperature Cycling (2)Criteria for judging the damage Item Symbol Test Conditions Criteria for Judgement Min. Max. Forward Voltage Vf If=60mA - U.S.L x1.2 Reverse Current Ir Vr=5V - U.S.L x2.0 Luminous Intensity Iv If=60mA L.S.L x 0.5 - Page 15/16 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃±5 ℃for 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Page 16/16