M52723ASP Dynamic Focus REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Description The M52723ASP is semiconductor integrated circuit for Multi-Sync display monitors. It generates horizontal and vertical parabola waves, and it can revise focus of CRT monitors. Features • It can control phase of horizontal wave. • It contains the horizontal saw wave generator and Auto Gain Control circuit, so that it is able to keep the amplitude constant if frequency change. • It change the parabola wave inretrace period to constant voltage in order to reduce load at the amplitude after IC. Application CRT display monitor Recommended Operating Condition Supply voltage range: 11.5 to 12.5 V Rated supply voltage: 12 V Block Diagram V-VCC VHS INPUT H-GND 20 19 18 H-PULSE H-DELAY INPUT CAPACITOR 17 16 VPH INPUT VREF OUTPUT 15 14 13 H-Pulse Delay AGC RETRACE CAPACITOR 12 11 AGC DET Vref X2 Buffer Para.Amp AGC TRACE VREF RESISTOR CAPACITOR SW X2 Para.Amp & Limiter Buffer 1 2 3 4 5 6 V-GND V-SAW INPUT VREF INPUT V-PARA OUTPUT VGV INPUT VGH INPUT REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 1 of 22 7 H-SAW Generator 8 H-PARA H-SAW OUTPUT RETRACE 9 10 H-SAW TRACE H-VCC M52723ASP Pin Arrangement M52723ASP V-GND 1 20 V-VCC V-SAW INPUT 2 19 VHS INPUT VREF INPUT 3 18 H-GND V-PARA OUTPUT 4 17 H-PULSE INPUT VGV INPUT 5 16 H-DELAY CAPACITOR VGH INPUT 6 15 VPH INPUT H-PARA OUTPUT 7 14 VREF OUTPUT H-SAW RETRACE 8 13 VREF RESISTOR H-SAW TRACE 9 12 AGC TRACE CAPACITOR H-VCC 10 11 AGC RETRACE CAPACITOR (Top view) Outline: PRDP0020BA-A (20P4B) Absolute Maximum Ratings (Ta = 25°C) Ratings Item Symbol Supply voltage Power dissipation Operating temperature Storage temperature Recommended operating voltage VCC Pd Topr Tstg Vopr Min −20 −40 Recommended operating voltage range Surge Vopr Vsurge 11.5 ±200 REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 2 of 22 Typ 12.0 Max 13.0 1237.6 +85 +150 Unit 12.5 V V V mW °C °C V M52723ASP Electrical Characteristics (Ta = 25°C, VCC = 12 V, unless otherwise noted) Symbol Min Limits Typ Max Unit Circuit current 1 Circuit current 2 Reference voltage output ICCH ICCV VREF 27.9 9.6 7.15 (10) Measure (20) Measure (14) Measure 10 20 14 DREF 21.5 7.4 6.95 49 mA mA V Reference voltage temperature drift Horizontal Block H-pulse low input range 15.1 5.2 6.75 ppm/ deg (14) Measure 14 VIL 0.0 2.0 V (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 3.2 V in 7 H-pulse high input range VIH 3.0 VCC −2.0 V 7 H-pulse low input current IIL −5.0 −0.6 −0.1 µA (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 3.2 V in (17) 0 V in, measure H-pulse high input current H parabola width IIH TW −1.0 0.50 0.0 0.70 1.0 0.90 µA µs H parabola delay 1 TD1 −0.09 0.09 0.35 µs (6) 4.0 V in (7) Measure (15) 0 V in (17) fH = 50 kHz H-pulse in (19) 3.2 V in 7 H parabola delay 2 TD2 0.19 0.41 0.65 µs (6) 4.0 V in (7) Measure (15) 1.5 V in (17) fH = 50 kHz H-pulse in (19) 3.2 V in 7 H parabola delay 3 TD3 2.65 2.95 3.20 µs (6) 4.0 V in (7) Measure (15) 4.0 V in (17) fH = 50 kHz H-pulse in (19) 3.2 V in 7 Delay temperature drift DD −0.08 ns/ deg (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 3.2 V in 7 Pin15 input current H parabola amplitude I15 VHP −5.0 7.5 −0.4 8.2 −0.1 8.9 µA VP-P (15) 2.5 V in, measure 15 7 Item REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 3 of 22 Test Conditions (17) 5 V in, measure (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 3.2 V in (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in Pin No. 17 17 7 M52723ASP Electrical Characteristics (cont.) Item Symbol Min H para. freq. characteristics 1 FHP1 −0.2 H para. freq. characteristics 2 FHP2 H para. VCC characteristics 1 Limits Typ Max Unit 0.0 0.2 V (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 24 kHz H-pulse in (19) 4.0 V in 7 −0.2 0.0 0.2 V (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 110 kHz H-pulse in (19) 4.0 V 7 VVHP1 −0.1 0.0 0.1 V (6) 2.5 V in (7) Measure (15) 3.0 V in (10) (20) 11.5 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in 7 H para. VCC characteristics 2 VVHP2 −0.1 0.0 0.1 V (6) 2.5 V in (7) Measure (15) 3.0 V in (10) (20) 12.5 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V 7 H para. size temperature drift DHP −275 ppm/ deg (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in 7 H para. size control 1 SHP1 7.5 8.2 8.9 VP-P (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in 7 H para. size control 2 SHP2 20 25 30 % (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 2.0 V in 7 H para. size control 3 SHP3 −5 0 5 % (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 0 V in 7 REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 4 of 22 Test Conditions Pin No. M52723ASP Electrical Characteristics (cont.) Item Symbol Min H para. gain control 1 GHP1 0.7 H para. gain control 2 GHP2 H para. gain control 3 GHP3 H para. limit size temperature drift Limits Typ Max Unit 0.9 1.1 VP-P (6) 1.0 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in 7 4.2 4.7 5.2 (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in 7 8.36 8.76 9.16 VP-P (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in 7 DLI 106 ppm/ deg (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 50 kHz H-pulse in (19) 4.0 V in 7 Pin6 input current Pin19 input current Vertical Block V parabola accuracy 1 I6 I19 −5.0 −5.0 −0.4 −0.4 −0.1 −0.1 µA µA (16) 2.5 V in, measure (19) 2.0 V in, measure 6 19 AVP1 9.5 10.0 10.5 V (2) 1.9 V in (3) 3.5 V in (4) Measure (5) 4.0 V in 4 V parabola accuracy 2 AVP2 6.23 6.73 7.23 V (2) 2.7 V in (3) 3.5 V in (4) Measure (5) 4.0 V in 4 V parabola accuracy 3 AVP3 20 25 30 % (2) 3.5 V in (3) 3.5 V in (4) Measure (5) 4.0 V in 4 V parabola accuracy 4 AVP4 20 25 30 % (2) 4.3 V in (3) 3.5 V in (4) Measure (5) 4.0 V in 4 V parabola accuracy 5 AVP5 90 100 110 % (2) 5.1 V in (3) 3.5 V in (4) Measure (5) 4.0 V in 4 V parabola amplitude 1 GVP1 0.0 0.0 0.1 VP-P (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 1.0 V in 4 REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 5 of 22 Test Conditions Pin No. M52723ASP Electrical Characteristics (cont.) Symbol Min. Limits Typ. Max. Unit V parabola amplitude 2 GVP2 2.77 3.12 3.47 VP-P (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 2.5 V in 4 V parabola amplitude 3 GVP3 6.26 6.56 6.86 VP-P (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 4.0 V in 4 V para. freq. characteristics 1 FVP1 −0.1 0.0 0.1 V (2) fV = 50 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 4.0 V in 4 V para. freq. characteristics 2 FVP2 −0.1 0.0 0.1 V (2) fV = 185 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 4.0 V in 4 V para. VCC. characteristics 1 VVP1 −0.1 0.0 0.1 V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 4.0 V in 4 V para. VCC. characteristics 2 VVP2 −0.1 0.0 0.1 V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 4.0 V in 4 V para. VCC. temperature drift DVP −325 ppm/ deg (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) measure (5) 4.0 V in 4 Pin2 input current I2 −5.0 −0.4 −0.1 µA (2) 3.5 V in, measure 2 Pin3 input current Pin5 input current I3 I5 −5.0 −5.0 −0.4 −0.4 −0.1 −0.1 µA µA (3) 3.5 V in, measure (5) 2.5 V in, measure 3 5 Item REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 6 of 22 Test Conditions Pin No. M52723ASP Switch and Voltage Condition Symbol ICCH ICCV VREF DREF VIL VIH IIL IIH TW TD1 TD2 TD3 DD I15 VHP FHP1 FHP2 VVHP1 VVHP2 DHP SHP1 SHP2 SHP3 GHP1 GHP2 GHP3 DLI I6 I19 AVP1 AVP2 AVP3 AVP4 AVP5 GVP1 GVP2 GVP3 FVP1 FVP2 VVP1 VVP2 DVP I2 I3 I5 SW2 SW3 a a Switch SW5 SW6 SW10 SW15 SW17 SW19 SW20 VCC a a b a b a a 12.0 b a a b a V2 3.5 V5 2.5 Voltage (V) V6 V15 2.5 3.0 V17 0 V19 2.0 a 4.0 3.2 b 2.5 2.0 a 4.0 0 5.0 0 2.0 4.0 b a 2.5 0 1.5 4.0 3.0 3.0 3.2 11.5 12.5 12.0 4.0 2.0 0 4.0 1.0 2.5 4.0 b a b b a 2.5 4.0 1.9 2.7 4.3 5.1 b 1.0 2.5 4.0 11.5 12.5 12.0 c a 3.5 b a b REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 7 of 22 2.5 0 4.0 2.0 2.0 M52723ASP Input Signal 5.0 V Typ PG (Input signal to pin 17) VTH = 2.5 V 0 V Typ Pulse width 3 µs Frequency 24 to 120 kHz 1.6 V SG (Input signal to pin 2) 3.5 V 1.6 V Frequency 50 to 185 Hz Electrical Characteristics Test Method ICCH Circuit Current1 Measure the input current to pin 10. ICCV Circuit Current2 Measure the input current to pin 20. VREF Reference Voltage Output Measure the output voltage at pin 14. DREF Reference Voltage Temperature Drift Measure temperature drift of pin 14. (−20°C to 85°C) VIL H-pulse Low Input Range Input horizontal pulse which low level is 2 V in pin 17 and confirm output horizontal signal at pin 7. 5.0 V Input signal to pin 17 2.0 V Output signal at pin 7 REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 8 of 22 M52723ASP VIH H-pulse High Input Range Input horizontal pulse which high level is 3 V in pin 17 and confirm output horizontal signal at pin 7. 3.0 V Input signal to pin 17 0V Output signal at pin 7 TW H Parabola Width Measure the time width of retrace period at pin 7. Input signal to pin 17 TW TD1 H Parabola Delay1, TD2 H Parabola Delay2, TD3 H Parabola Delay3 Measure the delay time from rise time of input signal to middle point of raise waveform point and down waveform point which voltage is retrace voltage +1.5 V when the voltage of pin 15 is 0 V, 1.5 V, and 4 V. 5.0 V Input signal to pin 17 0V Output signal at pin 7 1.5 V TD1, TD2, TD3 REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 9 of 22 M52723ASP DD Delay Temperature Drift Measure the temperature drift of the delay time. (−20°C to 85°C) I15 Pin 15 Input Current Measure the input current to pin15 when the voltage of pin 15 is 2.5 V. VHP H Parabola Amplitude Measure the amplitude of parabola waveform at pin 7 and it is defined HP50 kHz. FHP1 H Para. Freq. Characteristics1 When the frequency of input signal in pin 17 is 24 kHz, the amplitude of parabola waveform at pin 7 is defined as HP24 kHz. FHP1 = HP50 kHz − HP24 kHz FHP2 H Para. Freq. Characteristics2 When the frequency of input signal in pin 17 is 120 kHz, the amplitude of parabola waveform at pin 7 is defined as HP120 kHz. FHP2 = HP50 kHz − HP120 kHz VVHP1 H Para. VCC. Characteristics1 When the supply voltage of pin 10, 20 is 11.5 V, the amplitude of parabola waveform at pin 7 is defined as HP11.5 V. VVHP1 = HP50 kHz − HP11.5 V VVHP2 H Para. VCC. Characteristics2 When the supply voltage of pin 10, 20 is 12.5 V, the amplitude of parabola waveform at pin 7 is defined as HP12.5 V. VVHP2 = HP50 kHz − HP12.5 V DHP H Para. Size. Temperature Drift Measure the temperature drift of HP50 kHz. (−20°C to 85°C) SHP1 H Para. Size. Control1 Measure the amplitude of parabola waveform at pin 7 and it is defined as HP19 4.0 V. SHP2 H Para. Size. Control2 The amplitude of parabola waveform at pin 7 is defined as HP19 2.0 V. SHP2 = HP19 2.0 V HP19 4.0 V × 100 (%) SHP3 H Para. Size. Control3 The amplitude of parabola waveform at pin 7 is defined as HP19 0 V. SHP3 = HP19 0 V HP19 4.0 V × 100 (%) REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 10 of 22 M52723ASP GHP1 H Para. Gain Control1 Measure the amplitude of parabola waveform at pin 7 and it is defined as HP6 1.0 V. GHP2 H Para. Gain Control2 The amplitude of parabola waveform at pin 7 is defined as HP6 2.5 V. GHP2 = HP6 2.5 V − HP6 1.0 V 1.5 GHP3 H Para. Gain Control3 Measure the amplitude of parabola waveform at pin 7. (Limit level) DLI H Para. Limit Size Temperature Drift Measure temperature drift of GHP3. (−20°C to 85°C) I6 Pin 6 Input Current Measure the input current to pin 6 when voltage of pin 6 is 2.5 V. I19 Pin 19 Input Current Measure the input current to pin 19 when voltage of pin 19 is 2 V. AVP1 V Parabola Accuracy1 Measure the output voltage at pin 4 and it is defined as VP2 3.5 V. AVP2 V Parabola Accuracy2 The output voltage at pin 4 is defined as VP2 1.9 V. AVP2 = VP2 3.5 V − VP2 1.9 V AVP3 V Parabola Accuracy3 The output voltage at pin 4 is defined as VP2 2.7 V. AVP3 = VP2 3.5 V − VP2 2.7 V VP2 3.5 V − VP2 1.9 V × 100 (%) AVP4 V Parabola Accuracy4 The output voltage at pin 4 is defined as VP2 4.3 V. AVP4 = VP2 3.5 V − VP2 4.3 V VP2 3.5 V − VP2 1.9 V × 100 (%) AVP5 V Parabola Accuracy5 The output voltage at pin 4 is defined as VP2 5.1 V. AVP5 = VP2 3.5 V − VP2 5.1 V VP2 3.5 V − VP2 1.9 V × 100 (%) GVP1 V Parabola Amplitude1, GVP2 V Parabola Amplitude2, GVP3 V Parabola Amplitude3 Measure the amplitude of parabola waveform at pin 4 when the voltage of pin 5 is 0 V, 2.5 V, and 4 V. When the voltage of pin 5 is 4 V, the amplitude of parabola waveform is defined as VP70 Hz. REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 11 of 22 M52723ASP FVP1 V Para. Freq. Characteristics1 When the frequency of input signal in pin 2 is 50 Hz, the amplitude of parabola waveform at pin 4 is defined as VP50 Hz. FVP1 = VP70 Hz − VP50 Hz FVP2 V Para. Freq. Characteristics2 FVP2 = VP70 Hz − VP185 Hz VVP1 V Para. VCC. Characteristics1 When the voltage of pin 10, 20 is 11.5 V, the amplitude of parabola waveform is defined as VP11.5 V. VVP1 = VP70 Hz − VP11.5 V VVP2 V Para. VCC. Characteristics2 When the voltage of pin 10, 20 is 12.5 V, the amplitude of parabola waveform is defined as VP12.5 V. VVP2 = VP70 Hz − VP12.5 V DVP V Para. Temperature Drift Measure temperature drift of VP70 Hz. (−20°C to 85°C) I2 Pin 2 Input Current Measure the input current to pin 2 when the voltage of pin 2 is 3.5 V. I3 Pin 3 Input Current Measure the input current to pin 3 when the voltage of pin 3 is 3.5 V. I5 Pin 5 Input Current Measure the input current to pin 5 when the voltage of pin 5 is 3.5 V. REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 12 of 22 M52723ASP Test Circuit VCC 11.5 V 12.0 V 12.5 V A A SW20 a b b 2.5 V A H-Pulse a b a b SW19 + 33 µF V a SW17 0.01 µF 20 V15 0V 1.5 V 3.0 V 4.0 V 6.8 k SW15 100 pF 19 18 17 16 15 14 H-Pulse Delay 1 µF 0.01 µF 12 11 AGC DET Vref X2 Buffer Para.Amp 13 + V19 V17 0V 0V 2.0 V 5.0 V 3.2 V A 4.0 V 2.0 V SW X2 Para.Amp & Limiter H-SAW Generator Buffer 1 2 3 4 5 6 SW2 V2 a 1.9 V 2.7 V 3.5 V 4.3 V 5.1 V c SW3 SW5 Osc Scope b Dig-vol a b A a b 3.5 V 3.5 V V-saw 3.5 V 100 pF 9 100 pF 10 0.01 µF SW6 a b Osc Scope a + 33 µF b SW10 V6 V5 A 8 7 Hout A A 2.5 V 1.0 V 2.5 V 4.0 V 2.5 V A 1.0 V 2.5 V 4.0 V Units Resistance: Ω Capacitance: F REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 13 of 22 M52723ASP Typical Characteristics Thermal Derating (Maximum Rating) Power Dissipation Pd (mW) 1500 1250 1237.6 1000 750 643.6 500 250 0 −20 0 25 50 85 75 100 125 150 Ambient Temperature Ta (°C) Delay Control Voltage vs. Delay Time 3.5 Pin 17 input Pin 7 Delay Time (µs) 3.0 Delay time 2.5 2.0 Pin 7 Output 1.5 1.0 0.5 0 0 Usable range 0.5 1 1.3 Unusable range 2 3 4 5 Usable range Pin 15 Delay Control Voltage (V) Pin 7 Parabola Amplitude Ratio (%) H Size Control Voltage vs. H Parabola Amplitude Ratio 100 Pin 6 = 2.5 V const. 90 80 70 Amplitude ratio = 60 50 40 30 20 10 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 Pin 19 H Size Control Voltage (V) REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 14 of 22 Pin 7 output level Pin 7 output level at pin 19 = 4.0 V × 100 (%) M52723ASP Pin 7 H Parabola Amplitude (VP-P) H Gain Control Voltage vs. H Parabola Amplitude 12 11 10 9 8 7 8.76 VP-P (Limiting level) 6 5 4 3 Pin 19 = 4.0 V const. 2 1 0 1 0 2 3 4 Pin 6 H Gain Control Voltage (V) V Para DC Output Voltage Ratio Pin 4 Output Voltage Ratio (%) 100 Pin 3 = 3.5 V const. Pin 5 = 4.0 V const. 75 50 Output ratio = Pin4out (Pin 2 = 3.5 V) − Pin4out × 100 (%) Pin4out (Pin 2 = 3.5 V) − Pin4out (Pin 2 = 1.9 V) 25 0 1.9 2.7 3.5 4.3 5.1 Pin 2 Input Voltage (V) Pin 4 V Parabola Amplitude (VP-P) V Para Amp Gain Control Voltage vs. Output Amplitude 7 6.56 VP-P Pin 2 3.2 VP-P sawtooth wave input 6 5 4 3 2 1 0 0 1 2 3 4 5 Pin 5 V Para Amp Gain Control Voltage (V) REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 15 of 22 M52723ASP Timing Chart Horizontal Block 3.0 ≤ VIH ≤ (VCC - 2.0 V) Pin 17 H-pulse input VTH = 2.5 V VIL 2.0 V Pulse width 3 µs Internal H-pulse Pulse delay Pulse width 0.8 µs Pin 8 output Pin 7 output Vertical Block Pin 2 input 1.6 V 1.6 V Pin 4 output REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 16 of 22 Pin 3 input voltage = 3.5 V M52723ASP Application Example 12.0 V 10 µF The total resistance is above 10 kΩ 1% 0.01 µF 33 µF 0.01 µF VHS (H-Size) V-VCC 20 C∆ 100 pF H-GND 19 17 16 15 14 H-Pulse Delay 13 1 µF 0.01 µF 12 11 AGC DET Vref X2 Buffer Para.Amp 6.8 k VPH H-Pulse input 18 1% 1% + + 0.01 µF SW X2 Para.Amp & Limiter H-SAW Generator Buffer 1 V-GND 2 V-Saw input 3 VREF 4 Vout 5 VGV (H Gain) 6 VGH (H Gain) 0.01 µF 7 8 9 Hout 0.01 µF 10 0.01 µF H-VCC C∆ 100 pF C∆ 100 pF + 33 µF 2 VP-P 10 µH + 3.2 VP-P 2.2 µF 1% + 4.7 µF above 10 kΩ 1% To amplifier above 10 kΩ V H/V Deflection IC DAC Units Resistance: Ω Capacitance: F REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 17 of 22 M52723ASP Pin Description Pin No. 1 2 Name V-GND Vsawi DC Voltage (V) 3.5 V Peripheral Circuit Function GND of vertical block Vertical sawtooth wave input pin. V-VCC 50 µA 1.6 V V SAWREF 1.6 V = 3.5 V 1k 2 V-GND 3 Vsawref 3.5 V V-VCC 50 µA Vertical reference voltage input pin. (3.5 V) 1k 3 V-GND 4 Vout 10 V (Peak) Vertical parabola wave output pin. V-VCC 200 4 1 mA Peak voltage = 10 V (fixed) Amplitude is possible to control by pin 5 V-GND 5 VGV 1.0 to 4.0 V V-VCC 50 µA Vertical parabola wave gain control voltage input pin. Input voltage range is 1.0 to 4.0 V. 1k 5 V-GND 6 VGH 1.0 to 4.0 V H-VCC 50 µA 1k 6 H-GND REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 18 of 22 Horizontal parabola wave gain control voltage input pin. Input voltage range is 1.0 to 4.0 V. M52723ASP Pin Description (cont.) Pin No. 7 Name Hout DC Voltage (V) 9.2 V (Peak) Peripheral Circuit Function Horizontal parabola wave output pin. H-VCC Peak voltage = 9.2 V (fixed) 200 Amplitude is possible to control by pin 6 and pin 19. 7 1 mA H-GND 8 Cret 7.1 V (Top) 4.9 V (Bottom) H-VCC 0.25 mA Connection pin of horizontal retrace capacitor. Recommended capacitance is 100 pF. 7.1 V 8 4.9 V 1.5 k H-GND 9 Ctrc 7.1 V (Top) 4.9 V (Bottom) 60 µA 37 µA Connection pin of horizontal trace capacitor. Recommended capacitance is 100 pF. H-VCC 7.1 V 9 4.9 V 2k 510 2k 70 µA H-GND 10 11 H-VCC CAGCr 12.0 V 2.5 V Connection pin of horizontal sawtooth wave AGC retrace capacitor. Recommended capacitance is 0.01 µF. H-VCC 11 1.5 k H-GND REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 19 of 22 VCC of horizontal block. M52723ASP Pin Description (cont.) Pin No. 12 Name CAGC DC Voltage (V) 4.0 V Peripheral Circuit Function Connection pin of horizontal AGC capacitor. Recommended capacitance is 1 µF. H-VCC 12 7.5 k 1.5 k H-GND 13 VREFR 1.28 V Connection pin of reference current source resister. Recommended resistance is 6.8 kΩ. H-VCC 4k 13 H-GND 14 VREFO 7.0 V Reference voltage output for horizontal pulse delay circuit. Should be connect more than 10 kΩ external resister. H-VCC 10 p 14 50 µA H-GND 15 VPH 0 to 0.5 V 1.3 to 4.0 V 0.2 mA H-VCC 50 µA 15 Delay adjustment voltage input pin of horizontal pulse. Input voltage range is 1.3 to 4.0 V. At 0 to 0.5 V, delay is minimized. (0.5 to 1.3 V is unusable range.) 1k H-GND 16 Chpd 0V (Bottom) H-VCC 2k 2k 50 µA Connection pin of horizontal pulse delay timing capacitor. Recommended capacitance is 100 pF. 0.5 to 5.0 VP-P H 16 H-GND REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 20 of 22 1k 0V M52723ASP Pin Description (cont.) Pin No. 17 Name HPin DC Voltage (V) Peripheral Circuit H-VCC 50 µA 17 Function Horizontal pulse input pin. Low input level is less than 2.0 V, and high is 3.0 to 10 V. (at VCC = 12 V) 1k 50 k H-GND 18 19 H-GND VHS 0 to 4 V GND of horizontal block H-VCC 50 µA 19 Horizontal size control voltage input pin. Input voltage range is 0 to 4 V. 1k H-GND 20 V-VCC 12.0 V REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 21 of 22 VCC of vertical block M52723ASP Package Dimensions RENESAS Code PRDP0020BA-A Previous Code 20P4B MASS[Typ.] 1.0g 11 1 10 c *1 E 20 e1 JEITA Package Code P-SDIP20-6.3x19-1.78 NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET. *2 A A2 D L A1 Reference Symbol *3 b 3 e SEATING PLANE bp e1 D E A A1 A2 bp b3 c e L REJ03F0191-0201 Rev.2.01 Mar 31, 2008 Page 22 of 22 Dimension in Millimeters Min Nom Max 7.32 7.62 7.92 18.8 19.0 19.2 6.15 6.3 6.45 4.5 0.51 3.3 0.38 0.48 0.58 0.9 1.0 1.3 0.22 0.27 0.34 0° 15° 1.528 1.778 2.028 3.0 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2377-3473 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 © 2008. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.2