M52759SP Uniformity for CRT Display Monitor REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Description M52759SP is semiconductor integrated circuit for uniformity of CRT display monitor. It generates horizontal and vertical parabola waves and is able to revise contrast of CRT display monitor if it is used with Video Pre.Amp. M52742SP that has uniformity circuit. Features • It can control phase of horizontal wave. • It can changes the parabola wave unbalance. • It contains the horizontal saw wave generator and Auto Gain Control circuit, so that it is able to keep the amplitude constant if frequency change. • It can changes the parabola wave unbalance. • Frequency Band Width: horizontal 24 to 120 kHz Vertical 50 to 185 Hz • Input: horizontal 5 VP-P Pulse Vertical 3.2 VP-P V Saw Application CRT display monitor Recommended Operating Condition Supply voltage range: 11.5 V to 12.5 V Rated supply voltage: 12 V REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 1 of 26 M52759SP Block Diagram Hbias input H-GND H-pulse input 20 19 18 17 16 VPH input Vref output 15 14 13 H-Pulse Delay 12 11 AGC DET Vref X2 Buffer Para.Amp + V-VCC SW Para.Amp & Limiter X2 H-SAW Generator Buffer 1 2 3 4 5 6 V-GND V-saw input Vbias input V-para output VGV input VGH input 7 8 H-para output Pin Arrangement M52759SP V-GND 1 20 V-VCC V-saw input 2 19 Hbias Vbias 3 18 H-GND V-para output 4 17 H-pulse input VGV input 5 16 H-delay capacitor VGH input 6 15 VPH input H-para output 7 14 Reference voltage H-saw retrace 8 13 Reference voltage resistor H-saw trace 9 12 AGC trace capacitor H-VCC 10 11 AGC retrace capacitor (Top view) Outline: PRDP0020BA-A (20P4B) REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 2 of 26 9 10 H-VCC M52759SP Absolute Maximum Ratings (Ta = 25°C, Surge capacity = 200 pF) Item Symbol Ratings Typ. Max. Unit Supply voltage Power dissipation Operating temperature Storage temperature Recommended operating voltage VCC Pd Topr Tstg Vopr −20 −40 12.0 13.0 1237.6 +85 +150 V mW °C °C V Recommended operating voltage range Surge Vopr' Vsurge 11.5 ±200 12.5 V V Min. Thermal Derating Power Dissipation Pd (mW) 1500 1237.6 1000 643.6 500 0 −20 0 25 50 75 85 100 125 Ambient Temperature Ta (°C) REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 3 of 26 150 M52759SP Electrical Characteristics (Ta = 25°C, VCC = 12 V, unless otherwise noted) Item Symbol Limits Min. Typ. 15.1 21.5 5.2 7.4 6.75 6.95 49 Max. 27.9 9.6 7.15 Circuit current 1 Circuit current 2 Reference voltage output ICCH ICCV VREF Reference voltage temperature drift Horizontal Block H-pulse low input range DREF VIL 0.0 2.0 H-pulse high input range VIH 3.0 H-pulse low input current H-pulse high input current H parabola width IIL IIH TW −5.0 −1.0 0.6 H parabola delay 1 TD1 H parabola delay 2 Unit Test Conditions Pin No. mA mA V (10) Measure (20) Measure (14) Measure 10 20 14 ppm/ deg (14) Measure 14 V (6) 2.4 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 VCC −2.0 V 7 −0.6 0.0 0.8 −0.1 1.0 1.0 µA µA µs (6) 2.4 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in (17) 0 V in, measure (17) 5 V in, measure 0.1 0.3 0.5 µs (6) 2.4 V in (7) Measure (15) 0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 TD2 0.4 0.6 0.8 µs (6) 2.4 V in (7) Measure (15) 1.3 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 H parabola delay 3 TD3 2.9 3.1 3.3 µs (6) 2.4 V in (7) Measure (15) 4.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 Delay temperature drift DD 0.08 ns/ deg (6) 2.4 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 Pin 15 input current I15 −5.0 −0.3 −0.1 µA (17) 2.5 V in, measure 15 REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 4 of 26 (6) 2.4 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 17 17 7 M52759SP Electrical Characteristics (cont.) Item Symbol Limits Typ. −2.2 Max. −1.8 Unit V (6) 1.8 V in (7) Measure (15) 0 V in (17) fH = 96 kHz H-pulse in (19) 5.7 V in 7 Test Conditions Pin No. H para. unbalance control 1 UHP1 Min. −2.6 H para. unbalance control 2 UHP2 0.1 0.5 0.9 V (6) 2.4 V in (7) Measure (15) 0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 H para. unbalance control 3 UHP3 1.7 2.1 2.5 V (6) 1.8 V in (7) Measure (15) 0 V in (17) fH = 96 kHz H-pulse in (19) 6.4 V in 7 H para. unbalance VCC. character 1 VUHP1 −0.2 0.0 0.2 V (6) 2.4 V in (7) Measure (15) 0 V in (10) (20) 11.5 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 H para. unbalance VCC. character 2 VUHP2 −0.2 0.0 0.2 V (6) 2.4 V in (7) Measure (15) 0 V in (10) (20) 12.5 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 H para. unbalance temperature drift DUHP −2.2 mV/ deg (6) 2.4 V in (7) Measure (15) 0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 H para. gain control 1 GHP1 0.2 0.4 0.6 VP-P (6) 1.0 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 H para. gain control 2 GHP2 2.9 3.3 3.7 VP-P (6) 2.5 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 H para. gain control 3 GHP3 5.3 6.0 6.7 VP-P (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 5 of 26 M52759SP Electrical Characteristics (cont.) Item Symbol Limits Typ. Max. 0.0 0.2 H para. freq. characteristics 1 FHP1 Min. −0.2 H para. freq. characteristics 2 FHP2 −0.2 0.0 H para. VCC characteristics 1 VVHP1 −0.2 H para. VCC characteristics 2 VVHP2 H para. size temperature drift DHP Pin 6 input current Pin 19 input current Vertical Block V parabola accuracy 1 Unit Test Conditions Pin No. V (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 24 kHz H-pulse in (19) 6.1 V in 7 0.2 V (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 120 kHz H-pulse in (19) 6.1 V in 7 0.0 0.2 V (6) 4.0 V in (7) Measure (15) 3.0 V in (10) (20) 11.5 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 −0.2 0.0 0.2 V (6) 4.0 V in (7) Measure (15) 3.0 V in (10) (20) 12.5 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 −1.3 mV/ deg (6) 4.0 V in (7) Measure (15) 3.0 V in (17) fH = 96 kHz H-pulse in (19) 6.1 V in 7 I6 I19 −5.0 0.1 −0.3 0.3 −0.1 5.0 µA µA (6) 2.4 V in, measure (19) 6.1 V in, measure 6 19 AVP1 4.5 5.0 5.5 V (2) 3.5 V in (3) 3.5 V in (4) Measure (5) 2.3 V in 4 V parabola accuracy 2 AVP2 2.5 3.0 3.5 V (2) 1.9 V in (3) 3.5 V in (4) Measure (5) 2.3 V in 4 V parabola accuracy 3 AVP3 20 25 30 % (2) 2.7 V in (3) 3.5 V in (4) Measure (5) 2.3 V in 4 V parabola accuracy 4 AVP4 20 25 30 % (2) 4.3 V in (3) 3.5 V in (4) Measure (5) 2.3 V in 4 V parabola accuracy 5 AVP5 90 100 110 % (2) 5.1 V in (3) 3.5V in (4) Measure (5) 2.3 V in 4 REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 6 of 26 M52759SP Electrical Characteristics (cont.) Item Symbol Limits Typ. Max. −2.5 −2.2 V para. unbalance control 1 UVP1 Min. −2.8 V para. unbalance control 2 UVP2 −0.3 0 V para. unbalance control 3 UVP3 2.2 V unbalance. VCC. characteristics 1 VUVP1 V unbalance. VCC. characteristics 2 Unit Test Conditions Pin No. V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 2.8 V in (4) Measure (5) 1.6 V in 4 0.3 V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 2.3 V in 4 2.5 2.8 V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 4.2 V in (4) Measure (5) 1.6 V in 4 −0.1 0.0 0.1 V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 2.3 V in (10) (20) 11.5 V in 4 VUVP2 −0.1 0.0 0.1 V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 2.3 V in (10) (20) 12.5 V in 4 V unbalance. temperature drift DUVP 0.5 mV/ deg (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 2.3 V in 4 V parabola amplitude 1 GVP1 0 0 0.3 VP-P (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 1.0 V in 4 V parabola amplitude 2 GVP2 2.1 2.4 2.7 VP-P (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 2.0 V in 4 V parabola amplitude 3 GVP3 4.2 4.7 5.2 VP-P (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 3.0 V in 4 V para. freq. characteristics 1 FVP1 −0.1 0.0 0.1 V (2) fV = 50 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 3.0 V in 4 V para. freq. characteristics 2 FVP2 −0.1 0.0 0.1 V (2) fV = 185 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 3.0 V in 4 REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 7 of 26 M52759SP Electrical Characteristics (cont.) Item Symbol Limits Typ. Max. 0.0 0.1 V para. VCC. characteristics 1 VVP1 Min. −0.1 V para. VCC. characteristics 2 VVP2 −0.1 0.0 V para. temperature drift DVP Pin 2 input current Pin 3 input current Pin 5 input current I2 I3 I5 −5.0 −5.0 −5.0 REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 8 of 26 Unit Test Conditions Pin No. V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 3.0 V in (10) (20) 11.5 V in 4 0.1 V (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 3.0 V in (10) (20) 12.5 V in 4 −2.2 mV/ deg (2) fV = 70 Hz, 3.2 VP-P saw wave in (3) 3.5 V in (4) Measure (5) 3.0 V in 4 −0.3 −0.3 −0.3 −0.1 −0.1 −0.1 µA µA µA (2) 3.5 V in, measure (3) 3.5 V in, measure (5) 2.3 V in, measure 2 3 5 M52759SP Switch and Voltage Condition Switch Symbol ICCH ICCV VREF DREF VIL VIH IIL IIH TW TD1 TD2 TD3 DD I15 UHP1 UHP2 UHP3 VUHP1 VUHP2 DUHP GHP1 GHP2 GHP3 FHP1 FHP2 VVHP1 VVHP2 DHP I6 I19 AVP1 AVP2 AVP3 AVP4 AVP5 UVP1 UVP2 UVP3 VUVP1 VUVP2 DUVP GVP1 GVP2 GVP3 FVP1 FVP2 VVP1 VVP2 DVP I2 I3 I5 SW2 SW3 SW5 a a a Voltage (V) SW6 SW10 SW15 SW17 SW19 SW20 a b a a b a a b a VCC V2 V3 V5 V6 V15 V17 V19 12.0 3.5 3.5 2.5 2.4 3.0 0 6.1 a b 0 5.0 a b a b a 1.8 2.4 1.8 2.4 11.5 12.5 12.0 1.0 2.5 4.0 0 1.3 4.0 3.0 0 0 5.7 6.1 6.4 6.1 3.0 11.5 12.5 12.0 b a 2.4 b b a 2.3 1.9 2.7 4.3 5.1 b 11.5 12.5 12.0 2.8 3.5 4.2 3.5 1.6 2.3 1.6 2.3 1.0 2.0 3.0 11.5 12.5 12.0 c a 3.5 b a b REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 9 of 26 2.3 0 6.1 M52759SP Input Signal 5.0 V Typ PG (Input signal to pin 17) VTH = 2.5 V 0 V Typ Pulse width above 1 µs Frequency 24 to 96 to 140 kHz 1.6 V SG (Input signal to pin 2) 3.5 V 1.6 V Frequency 50 to 70 to 185 Hz Electrical Characteristics Test Method ICCH Circuit Current1 Measure the input current to pin 10. ICCV Circuit Current2 Measure the input current to pin 20. VREF Reference Voltage Output Measure the output voltage at pin 14. DREF Reference Voltage Temperature Drift Measure temperature drift of pin 14. (−20°C to 85°C) VIL H-pulse Low Input Range Input horizontal pulse which low level is 2 V in pin 17 and confirm output horizontal signal at pin 7. 5.0 V Input signal to pin 17 2.0 V Output signal at pin 7 REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 10 of 26 M52759SP VIH H-pulse High Input Range Input horizontal pulse which high level is 3 V in pin 17 and confirm output horizontal signal at pin 7. 3.0 V Input signal to pin 17 0V Output signal at pin 7 TW H Parabola Width Measure the time width of retrace period at pin 7. TW Input signal to pin 17 TD1, TD2, TD3 H Parabola Delay Measure the delay time from rise time of input signal to start of retrace period of output signal when the voltage of pin 15 is 0 V, 1.3 V, and 4 V. 5.0 V Input signal to pin 17 0V TD1, TD2, TD3 Output signal at pin 7 DD Delay Temperature Drift Measure the temperature drift of the delay time. (−20°C to 85°C) I15 Pin 15 Input Current Measure the input current to pin 15 when the voltage of pin 15 is 2.5 V. REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 11 of 26 M52759SP UHP1, UHP2, UHP3 H para. Unbalance Control UHPS is defined as the voltage of parabola start point. UHPE is defined as the voltage of parabola end point. UHP1, UHP2, UHP3 is defined as follows UHP1, UHP2, UHP3 = UHPS − UHPE Measure the unbalance of parabola waveform at pin 4 when the voltage of pin 19 is 5.7 V, 6.1 V, and 6.4 V. Pin 6 is controlled so that the amplitude of parabola is 3 VP-P constant. UHPS Output signal at pin 7 UHP UHPE VUHP1 H para. Unbalance VCC. Characteristics1 When the supply voltage of pin 10, 20 is 11.5 V, the unbalance of parabola waveform at pin 7 is defined as UHP11.5 V. VUHP1 = UHP2 − UHP11.5 V VUHP2 H para. Unbalance VCC. Characteristics2 When the supply voltage of pin 10, 20 is 12.5 V, the unbalance of parabola waveform at pin 7 is defined as UHP12.5 V. VUHP2 = UHP2 − UHP12.5 V DUHP H para. Unbalance Temperature Drift Measure temperature drift of UHP2. (−20°C to 85°C) GHP1 H Para. Gain Control1 Measure the amplitude of parabola waveform at pin 7 and it is defined as HP−6, 1.0 V. GHP2 H Para. Gain Control2 The amplitude of parabola waveform at pin 7 is defined as HP−6, 2.5 V. GHP3 H Para. Gain Control3 The amplitude of parabola waveform at pin 7 is defined as HP−6, 4.0 V. FHP1 H Para. Freq. Characteristics1 When the frequency of input signal in pin 17 is 96 kHz, the amplitude of parabola waveform at pin 7 is defined as HP96 kHz. When the frequency of input signal is 24 kHz, the amplitude of parabola waveform is defined as HP24 kHz. FHP1 = HP96 kHz − HP24 kHz FHP2 H Para. Freq. Characteristics2 When the frequency of input signal in pin 17 is 140 kHz, the amplitude of parabola waveform at pin 7 is defined as HP120 kHz. FHP2 = HP96 kHz − HP140 kHz REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 12 of 26 M52759SP VVHP1 H Para. VCC. Characteristics1 When the supply voltage of pin 10, 20 is 12.0 V, the amplitude of parabola waveform at pin 7 is defined as HP12.0 V. When the supply voltage is 11.5 V, the amplitude of parabola waveform is defined as HP11.5 V. VVHP1 = HP12.0 V − HP11.5 V VVHP2 H Para. VCC. Characteristics2 When the supply voltage of pin 10, 20 is 12.5 V, the amplitude of parabola waveform at pin 7 is defined as HP12.5 V. VVHP2 = HP12.0 V − HP12.5 V DHP H Para. Size Temperature Drift Measure the temperature drift of HP96 kHz. (−20°C to 85°C) I6 Pin 6 Input Current Measure the input current to pin 6 when voltage of pin 6 is 2.4 V. I19 Pin 19 Input Current Measure the input current to pin 19 when voltage of pin 19 is 6.1 V. AVP1 V Parabola Accuracy1 Measure the output voltage at pin 4 and it is defined as VP−2, 3.5 V. AVP2 V Parabola Accuracy2 The output voltage at pin 4 is defined as VP−2, 1.9 V. AVP2 = VP−2, 1.9 V − VP−2, 3.5 V AVP3 V Parabola Accuracy3 The output voltage at pin 4 is defined as VP−2, 2.7 V. AVP3 = VP−2, 2.7 V − VP−2, 3.5 V × 100 (%) VP−2, 1.9 V − VP−2, 3.5 V AVP4 V Parabola Accuracy4 The output voltage at pin 4 is defined as VP−2, 4.3 V. AVP4 = VP−2, 4.3 V − VP−2, 3.5 V × 100 (%) VP−2, 1.9 V − VP−2, 3.5 V AVP5 V Parabola Accuracy5 The output voltage at pin 4 is defined as VP−2, 5.1 V. AVP5 = VP−2, 5.1 V − VP−2, 3.5 V × 100 (%) VP−2, 1.9 V − VP−2, 3.5 V REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 13 of 26 M52759SP UVP1, UVP2, UVP3 V Para. Unbalance Control UVPS is defined as the voltage of parabola start point. UVPE is defined as the voltage of parabola end point. UVP1, UVP2, UVP3 is defined as follows UVP1, UVP2, UVP3 = UVPS − UVPE Measure the unbalance of parabola waveform at pin 4 when the voltage of pin 3 is 2.8 V, 3.5 V, and 4.2 V. Pin 5 is controlled so that the amplitude of parabola is 3 VP-P constant. UVPS Output signal at pin 7 UVPE VUVP1 V Unbalance VCC. Characteristics1 When the supply voltage of pin 10, 20 is 11.5 V, the unbalance of parabola waveform at pin 4 is defined as UVP11.5 V. VUHP1 = UVP2 − UVP11.5 V VUVP2 V Unbalance VCC. Characteristics2 When the supply voltage of pin 10, 20 is 12.5 V, the unbalance of parabola waveform at pin 4 is defined as UVP 12.5 V. VUVP2 = UVP2 − UVP12.5 V DUVP V Unbalance Temperature Drift Measure temperature drift of UVP2 (−20°C to 85°C) GVP1, GVP2, GVP3 V Parabola Amplitude Measure the amplitude of parabola waveform at pin 4 when the voltage of pin 5 is 1 V, 2 V, and 3 V. FVP1 V Para. Freq. Characteristics1 When the frequency of input signal in pin 2 is 70 Hz, the amplitude of parabola waveform at pin 4 is defined as VP70 Hz. When the frequency of input signal is 50 Hz, the amplitude of parabola waveform is defined as VP50 Hz. FVP1 = VP70 Hz − VP50 Hz FVP2 V Para. Freq. Characteristics2 When the frequency of input signal in pin 2 is 185 Hz, the amplitude of parabola waveform at pin 4 is defined as VP185 Hz. FVP2 = VP70 Hz − VP185 Hz VVP1 V Para. VCC. Characteristics1 When the voltage of pin 10, 20 is 12.0 V, the amplitude of parabola waveform is defined as VP12.0 V. When the voltage is 11.5 V, the amplitude of parabola waveform is defined as VP11.5 V. VVP1 = VP12.0 V − VP11.5 V VVP2 V Para. VCC. Characteristics2 When the voltage of pin 10, 20 is 12.5 V, the amplitude of parabola waveform is defined as VP12.5 V. VVP2 = VP12.0 V − VP12.5 V REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 14 of 26 M52759SP DVP V Para. Temperature Drift Measure temperature drift of VP70 Hz. (−20°C to 85°C) I2 Pin 2 Input Current Measure the input current to pin 2 when the voltage of pin 2 is 3.5 V. I3 Pin 3 Input Current Measure the input current to pin 3 when the voltage of pin 3 is 3.5 V. I5 Pin 5 Input Current Measure the input current to pin 5 when the voltage of pin 5 is 2.4 V. REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 15 of 26 M52759SP Test Circuit VCC 11.5 V 12.0 V 12.5 V 20 A H-Pulse a b a SW19 SW17 19 18 b 17 V a SW15 16 15 14 H-Pulse Delay 12 11 AGC DET Vref X2 Buffer Para.Amp 13 0.01 µF 0.01 µF + 33 µF b 2.5 V A 7V a b V15 0V 1.3 V 3.0 V 4.0 V 1 µF A SW20 100 pF 6.1 V A V17 0V 5.0 V 6.8 k V19 5.7 V 6.1 V 6.4 V + V19 0V 5.7 V 6.1 V 6.4 V SW X2 Para.Amp & Limiter H-SAW Generator SW2 V2 a 1.9 V 2.7 V 3.5 V 4.3 V 5.1 V c 4 5 SW3 a b b A SW5 Osc Scope Dig-vol a 3.5 V b A 2.8 V 3.5 V 4.2 V REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 16 of 26 SW6 a A b Osc Scope A 2.3 V 1V 2V 3V 7 Hout V6 V5 3.5 V V-saw 6 2.4 V 1.0 V 2.4 V 2.5 V 4.0 V 8 9 10 + a 33 µF 3 100 pF 2 100 pF 1 0.01 µF Buffer b SW10 A M52759SP Typical Characteristics Horizontal Block Delay Control Voltage vs. Delay Time 3.5 Pin 7 Delay Time (µs) 3.0 Pin 17 input 2.5 Delay time 2.0 1.5 Pin 7 Output 1.0 0.5 0 0 Usable range 0.5 1 1.3 Unusable range 2 3 4 5 Usable range Pin 15 Delay Control Voltage (V) H Unbalance Control Bias Voltage vs. H Parabola Unbalance Pin 6 is controlled as the amplitude of parabola is 3 VP-P constant Pin 7 H Parabola Unbalance (V) Pin 7 output 2 1 0 −1 −2 5.7 5.9 6.1 6.3 6.5 Pin 19 H Unbalance Control Bias Voltage (V) Pin 7 H Parabola Amplitude (VP-P) H Gain Control Voltage vs. H Parabola Amplitude 7 Pin 19 = 6.1 V const. 6 5 4 3 2 1 0 0 1 2 3 4 Pin 6 H Gain Control Voltage (V) REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 17 of 26 5 M52759SP Vertical Block V Para DC Output Voltage Ratio Pin 4 Output Voltage Ratio (%) 100 Pin 3 = 3.5 V const. Pin 5 = 2.3 V const. 75 50 Output ratio = Pin 4out − Pin 4out@Pin 4 = 3.5 V × 100 (%) Pin 4out@Pin 2 = 1.9 V − Pin 4out@Pin 2 = 3.5 V 25 0 1.9 2.7 3.5 4.3 5.1 Pin 2 Input Voltage (V) V Unbalance Control Bias Voltage vs. V Parabola Unbalance Pin 4 V Parabola Unbalance (V) 3 Pin 5 is controlled as the amplitude of parabola is 3 VP-P constant Pin 4 output 2 1 0 −1 −2 −3 2.5 3.0 3.5 4.0 4.5 Pin 3 V Unbalance Control Bias Voltage (V) V Para Amp Gain Control Voltage vs. Output Amplitude Pin 4 V Para Amplitude (VP-P) 5 Pin 2 3.2 VP-P sawtooth wave input 4 3 2 1 0 0 1 2 3 4 Pin 5 V Para Amp Gain Control Voltage (V) REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 18 of 26 M52759SP Timing Chart Horizontal Block 3.0 ≤ VIH ≤ (VCC − 2.0 V) Pin 17 H-pulse input VTH = 2.5 V VIL ≤ 2.0 V Pulse width to 3 µs Internal H-pulse Pulse delay Pulse width to 0.8 µs Pin 8 output Pin 7 output Vertical Block Pin 2 input 1.6 V 1.6 V Pin 4 output REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 19 of 26 Pin 3 input voltage = 3.5 V M52759SP Application Example 1.8 k 100 p 1k Flyback Pulse in 3.9 k 20 19 18 17 15 14 13 11 AGC DET X2 Buffer Para.Amp 12 Vref H-Pulse 0.01 µF VPH 16 1 µF Hbias 6.8 k 100 pF V-VCC 0.01 µF 0.01 µF + VCC 12 V + 33 µF 1k SW Para.Amp X2 H-SAW Buffer Vbias 7 VGV (V Gain) 8 Hout 10 9 VGH (H Gain) V-saw input V Uniformity in M52742SP REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 20 of 26 CRT Monitor + HVCC 0.01 µF 6 47 µ 5 Vout 100 pF 0.01 µF 4 100 pF 3 0.01 µF 2 0.01 µF 1 V-GND M52759SP 17 VPH 16 14 H-Pulse Delay 13 1 µF 12 11 AGC DET Vref X2 Buffer Para.Amp 6.8 k 1% 1% 15 0.01 µF H-pulse input 0.01 µF H-GND 18 100 pF 0.01 µF Hbias 19 C∆ 0.01 µF 20 + V-VCC 1% 1% The total resistance is above 10 kΩ + 33 µF 10 µH 12.0 V SW Para.Amp & Limiter H-SAW Generator 7 Hout 8 9 2 VP-P 3.2 VP-P above 10 kΩ 2.2 µF 10 H-VCC + 10 µH 6 VGH (H Gain) 0.01 µF 0.01 µF 5 VGV (H Gain) 100 pF 4 Vout C∆ 3 Vbias 0.01 µF 2 V-saw input 0.01 µF 1 V-GND 100 pF Buffer C∆ X2 1% 1% 4.7 µF H/V Deflection IC REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 21 of 26 DAC above 10 kΩ V M52759SP Pin Description Pin No. 1 2 Name V-GND Vsawi DC Voltage (V) 3.5 V Peripheral Circuit Function GND of vertical block Vertical sawtooth wave input pin. V-VCC 50 µA Vbias 1k 2 V-GND 3 Vbias 2.8 to 4.2 V V-VCC 50 µA Vertical parabola unbalance control bias voltage input pin. Input voltage range is 2.8 to 4.2 V 1k 3 V-GND 4 Vout 5 V (Bottom) Vertical parabola wave output pin. V-VCC 200 Bottom voltage = 5 V (fixed) 4 Amplitude is possible to control by pin 5 1 mA V-GND 5 VGV 1.0 to 3.0 V V-VCC 50 µA Vertical parabola wave gain control voltage input pin. Input voltage range is 1.0 to 3.0 V. 1k 5 V-GND 6 VGH 1.0 to 4.0 V H-VCC 50 µA 1k 6 H-GND REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 22 of 26 Horizontal parabola wave gain control voltage input pin. Input voltage range is 1.0 to 4.0 V. M52759SP Pin Description (cont.) Pin No. 7 Name Hout DC Voltage (V) 2.4 to 9.2 V Peripheral Circuit Function Horizontal parabola wave output pin. H-VCC 200 Amplitude is possible to control by pin 6 7 1 mA H-GND 8 Cret 7.1 V (Top) 4.9 V (Bottom) H-VCC 0.25 mA Connection pin of horizontal retrace capacitor. Recommended capacitance is 100 pF. 8 7.1 V 1.5 k H-GND 9 Ctrc 7.1 V (Top) 4.9 V (Bottom) 60 µA 4.9 V 37 µA Connection pin of horizontal trace capacitor. Recommended capacitance is 100 pF. H-VCC 9 7.1 V 2k 510 2k 4.9 V 70 µA H-GND 10 11 H-VCC CAGCr 12.0 V 2.5 V Connection pin of horizontal sawtooth wave AGC retrace capacitor. Recommended capacitance is 0.01 µF. H-VCC 11 1.5 k H-GND REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 23 of 26 VCC of horizontal block. M52759SP Pin Description (cont.) Pin No. 12 Name CAGC DC Voltage (V) 4.0 V Peripheral Circuit Function Connection pin of horizontal AGC capacitor. Recommended capacitance is 1 µF. H-VCC 12 7.5 k 1.5 k H-GND 13 Vrefr 1.28 V Connection pin of reference current source resister. Recommended resistance is 6.8 kΩ. H-VCC 4k 13 H-GND 14 Vrefo 7.0 V Reference voltage output for horizontal pulse delay circuit. Should be connect more than 10 kΩ external resister. H-VCC 10 p 14 50 µA H-GND 15 VPH 0 to 0.5 V 1.3 to 4.0 V 0.2 mA H-VCC 50 µA 15 Delay adjustment voltage input pin of horizontal pulse. Input voltage range is 1.3 to 4.0 V. At 0 to 0.5 V, delay is minimized. (0.5 to 1.3 V is unusable range.) 1k H-GND 16 Chpd 0V (Bottom) H-VCC 2k 2k 50 µA Connection pin of horizontal pulse delay timing capacitor. Recommended capacitance is 100 pF. 0.5 to 5.0 VP-P H 16 H-GND REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 24 of 26 1k 0V M52759SP Pin Description (cont.) Pin No. 17 Name HPin DC Voltage (V) Peripheral Circuit H-VCC 50 µA 17 1k Function Horizontal pulse input pin. Low input level is less than 2.0 V, and high is 3.0 to 10 V. (at VCC = 12 V) 50 k H-GND 18 19 H-GND Hbias 5.7 to 6.4 V GND of horizontal block Horizontal parabola unbalance control bias voltage input pin. Input voltage range is 5.7 to 6.4 V. H-VCC 1k 19 1p 50 µA H-GND 20 V-VCC 12.0 V REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 25 of 26 VCC of vertical block M52759SP Package Dimensions RENESAS Code PRDP0020BA-A Previous Code 20P4B MASS[Typ.] 1.0g 11 1 10 c *1 E 20 e1 JEITA Package Code P-SDIP20-6.3x19-1.78 NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET. *2 A A2 D L A1 Reference Symbol *3 b 3 e SEATING PLANE bp e1 D E A A1 A2 bp b3 c e L REJ03F0197-0201 Rev.2.01 Mar 31, 2008 Page 26 of 26 Dimension in Millimeters Min Nom Max 7.32 7.62 7.92 18.8 19.0 19.2 6.15 6.3 6.45 4.5 0.51 3.3 0.38 0.48 0.58 0.9 1.0 1.3 0.22 0.27 0.34 0° 15° 1.528 1.778 2.028 3.0 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2377-3473 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 © 2008. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.2