SUBMINIATURE SOLID STATE LAMP Part Number: AM2520EC09 High Efficiency Red Features Description z Subminiature package. The High Efficiency Red source color devices are made with z Z-bend lead. Gallium Arsenide Phosphide on Gallium Phosphide Orange z Long life - solid state reliability. Light Emitting Diode. z Low package profile. z Moisture sensitivity level : level 3. z Package : 1000pcs / reel. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 5. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD1280 REV NO: V.11A DATE: MAR/18/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000462 Selection Guide Part No. Dice AM2520EC09 Iv (mcd) [2] @ 20mA Lens Type High Efficiency Red (GaAsP/GaP) Min. Typ. 50 100 *20 *50 Viewing Angle [1] 2θ1/2 20° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength High Efficiency Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 627 nm IF=20mA High Efficiency Red 617 nm IF=20mA Spectral Line Half-width High Efficiency Red 45 nm IF=20mA C Capacitance High Efficiency Red 15 pF VF=0V;f=1MHz VF [2] Forward Voltage High Efficiency Red 2 2.5 V IF=20mA IR Reverse Current High Efficiency Red 10 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 160 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1280 REV NO: V.11A DATE: MAR/18/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000462 High Efficiency Red AM2520EC09 SPEC NO: DSAD1280 REV NO: V.11A DATE: MAR/18/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000462 AM2520EC09 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAD1280 REV NO: V.11A DATE: MAR/18/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000462 PACKING & LABEL SPECIFICATIONS AM2520EC09 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAD1280 REV NO: V.11A DATE: MAR/18/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000462