T-1 3/4 (5mm) SOLID STATE LAMP Part Number: WP7113ID5V High Efficiency Red ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z Low power consumption. z The High Efficiency Red source color devices are made z Popular T-1 3/4 diameter package. with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode. z General purpose leads. z Electrostatic discharge and power surge could damage z Reliable and rugged. z Long life - solid state reliability. the LEDs. z It is recommended to use a wrist band or anti- z Available on tape and reel. electrostatic glove when handling the LEDs. z 5V internal resistor. z All devices, equipments and machineries must be z RoHS compliant. electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF2406 REV NO: V.6A DATE: JAN/23/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005047 Selection Guide Part No. Dice WP7113ID5V Lens Type High Efficiency Red (GaAsP/GaP) Iv (mcd) [2] V= 5V Min. Typ. 20 40 *12 *25 Red Diffused Viewing Angle [1] 2θ1/2 30° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength High Efficiency Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 627 nm VF=5V High Efficiency Red 617 nm VF=5V Spectral Line Half-width High Efficiency Red 45 nm VF=5V IF Forward Current High Efficiency Red 13 17.5 mA VF=5V IR Reverse Current High Efficiency Red 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Wavelength value is traceable to the CIE127-2007 compliant national standards. 3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Units Power dissipation 85 mW Forward Voltage 6 V Reverse Voltage 5 V Operating Temperature -40°C To +70°C Storage Temperature -40°C To +85°C Lead Solder Temperature [1] 260°C For 3 Seconds Lead Solder Temperature [2] 260°C For 5 Seconds Notes: 1. 2mm below package base. 2. 5mm below package base. SPEC NO: DSAF2406 REV NO: V.6A DATE: JAN/23/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005047 High Efficiency Red WP7113ID5V SPEC NO: DSAF2406 REV NO: V.6A DATE: JAN/23/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005047 PACKING & LABEL SPECIFICATIONS WP7113ID5V Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF2406 REV NO: V.6A DATE: JAN/23/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005047 SPEC NO: DSAF2406 REV NO: V.6A DATE: JAN/23/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005047 SPEC NO: DSAF2406 REV NO: V.6A DATE: JAN/23/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005047