SOT-23 SURFACE MOUNT LED LAMP Part Number: AM23ESGC High Efficiency Red Super Bright Green Features Descriptions z SOT-23 package surface mount LED lamp. z The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide z Low power consumption. z Long life - solid state reliability. Orange Light Emitting Diode. z The Super Bright Green source color devices are made z Package: 2000pcs / reel. z Moisture sensitivity level : level 3. with Gallium Phosphide Green Light Emitting Diode. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the lead emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 5.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAA8612 REV NO: V.12A DATE: MAR/17/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000004 Selection Guide Part No. Dice Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 5 12 *3 *5 5 10 *5 *10 2θ1/2 High Efficiency Red (GaAsP/GaP) AM23ESGC Water Clear Super Bright Green (GaP) 140° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength High Efficiency Red Super Bright Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 627 565 nm IF=20mA High Efficiency Red Super Bright Green 617 568 nm IF=20mA Spectral Line Half-width High Efficiency Red Super Bright Green 45 30 nm IF=20mA C Capacitance High Efficiency Red Super Bright Green 15 15 pF VF=0V;f=1MHz VF [2] Forward Voltage High Efficiency Red Super Bright Green 2 2.2 2.5 2.5 V IF=20mA IR Reverse Current High Efficiency Red Super Bright Green 10 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Super Bright Green Units Power dissipation 75 62.5 mW DC Forward Current 30 25 mA Peak Forward Current [1] 160 140 mA Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAA8612 REV NO: V.12A DATE: MAR/17/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000004 AM23ESGC High Efficiency Red SPEC NO: DSAA8612 REV NO: V.12A DATE: MAR/17/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000004 Super Bright Green SPEC NO: DSAA8612 REV NO: V.12A DATE: MAR/17/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000004 AM23ESGC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAA8612 REV NO: V.12A DATE: MAR/17/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000004 PACKING & LABEL SPECIFICATIONS AM23ESGC Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAA8612 REV NO: V.12A DATE: MAR/17/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1202000004