apbda3020surkcgkc-gx

3.0x2.0mm RIGHT ANGLE SMD LED
Part Number: APBDA3020SURKCGKC-GX
Hyper Red
Green
Features
Descriptions
z 3.0mmx2.0mm SMT LED,2.8mm thickness.
z The Hyper Red source color devices are made with Al
GaInP on GaAs substrate Light Emitting Diode.
z Low power consumption.
z Ideal for back light and indicator
z The Green source color devices are made with AlGaInP
on GaAs substrate Light Emitting Diode.
z Package : 2000pcs / reel.
z When soldered in the sideview configuration, the maximum
shear tolerance of the epoxy lens is 300g.
z Moisture sensitivity level : level 3.
z Tinned pads for improved solderability
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2(0.008") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAL0182
REV NO: V.7A
DATE: MAR/17/2015
PAGE: 1 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203012005
Selection Guide
Part No.
Dice
Viewing
Angle [1]
Iv (mcd) [2]
@ 20mA
Lens Type
Min.
Typ.
500
900
*120
*300
120
300
*120
*300
2θ1/2
Hyper Red (AlGaInP)
APBDA3020SURKCGKC-GX
Water Clear
Green (AlGaInP)
15°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Hyper Red
Green
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
645
574
nm
IF=20mA
Hyper Red
Green
630
570
nm
IF=20mA
Spectral Line Half-width
Hyper Red
Green
28
20
nm
IF=20mA
C
Capacitance
Hyper Red
Green
35
15
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Hyper Red
Green
1.95
2.1
2.5
2.5
V
IF=20mA
IR
Reverse Current
Hyper Red
Green
10
10
uA
VR = 5V
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Hyper Red
Green
Units
Power dissipation
75
75
mW
DC Forward Current
30
30
mA
Peak Forward Current [1]
185
150
mA
Reverse Voltage
5
V
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAL0182
REV NO: V.7A
DATE: MAR/17/2015
PAGE: 2 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203012005
APBDA3020SURKCGKC-GX
Hyper Red
SPEC NO: DSAL0182
REV NO: V.7A
DATE: MAR/17/2015
PAGE: 3 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203012005
Green
SPEC NO: DSAL0182
REV NO: V.7A
DATE: MAR/17/2015
PAGE: 4 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203012005
APBDA3020SURKCGKC-GX
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAL0182
REV NO: V.7A
DATE: MAR/17/2015
PAGE: 5 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203012005
PACKING & LABEL SPECIFICATIONS
APBDA3020SURKCGKC-GX
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL0182
REV NO: V.7A
DATE: MAR/17/2015
PAGE: 6 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203012005