APHB1608CGKSURKC

1.6x0.8x0.5mm BI-COLOR SURFACE MOUNT
LED
Part Number: APHB1608CGKSURKC
Green
Hyper Red
Descriptions
Features
 The Green source color devices are made with AlGaInP
 1.6mmX0.8mm SMT LED, 0.5mm thickness.
 Compatible with reflow soldering.
 Available in various color combination.
on GaAs substrate Light Emitting Diode.
 The Hyper Red source color devices are made with
AlGaInP on GaAs substrate Light Emitting Diode.
 Package: 2000pcs / reel.
 Moisture sensitivity level : level 3.
 Tinned pads for improved solderability.
 RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.15(0.006") unless otherwise noted.
3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4.The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAK6423
REV NO: V.7A
DATE: NOV/06/2014
PAGE: 1 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203011105
Selection Guide
Part No.
Dice
Viewing
Angle [1]
Iv (mcd) [2]
@ 20mA
Lens Type
Min.
Typ.
20
50
*20
*50
120
250
*40
*90
2θ1/2
Green (AlGaInP)
APHB1608CGKSURKC
Water Clear
Hyper Red (AlGaInP)
130°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
*Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Green
Hyper Red
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
574
645
nm
IF=20mA
Green
Hyper Red
570
630
nm
IF=20mA
Spectral Line Half-width
Green
Hyper Red
20
28
nm
IF=20mA
C
Capacitance
Green
Hyper Red
15
35
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Green
Hyper Red
2.1
1.95
2.5
2.5
V
IF=20mA
IR
Reverse Current
Green
Hyper Red
10
10
uA
VR = 5V
Notes:
1.Wavelength: +/-1nm.
2.Forward Voltage: +/-0.1V.
3.Wavelength value is traceable to the CIE127-2007 compliant national standards.
4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Green
Hyper Red
Units
Power dissipation
75
75
mW
DC Forward Current
30
30
mA
Peak Forward Current [1]
150
185
mA
Reverse Voltage
5
V
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAK6423
REV NO: V.7A
DATE: NOV/06/2014
PAGE: 2 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203011105
APHB1608CGKSURKC
Green
SPEC NO: DSAK6423
REV NO: V.7A
DATE: NOV/06/2014
PAGE: 3 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203011105
Hyper Red
SPEC NO: DSAK6423
REV NO: V.7A
DATE: NOV/06/2014
PAGE: 4 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203011105
APHB1608CGKSURKC
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAK6423
REV NO: V.7A
DATE: NOV/06/2014
PAGE: 5 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203011105
PACKING & LABEL SPECIFICATIONS
APHB1608CGKSURKC
Terms and conditions for the usage of this document
1.The information included in this document reflects representative usage scenarios and is intended
for technical reference only.
2.The part number, type, and specifications mentioned in this document are subject to future change
and improvement without notice. Before production usage customer should refer to the latest
datasheet for the updated specifications.
3.When using the products referenced in this document, please make sure the product is being
operated within the environmental and electrical limits specified in the datasheet. If customer usage
exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4.The information in this document applies to typical usage in consumer electronics applications.
If customer's application has special reliability requirements or have life-threatening liabilities,
such as automotive or medical usage, please consult with Kingbright representative for further
assistance.
5.The contents and information of this document may not be reproduced or re-transmitted without
permission by Kingbright.
6.All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAK6423
REV NO: V.7A
DATE: NOV/06/2014
PAGE: 6 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203011105