Datasheet - Kingbright

T-1 (3mm) SOLID STATE LAMP
Part Number: WP710A10SGD5V
ATTENTION
Super Bright Green
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z Low power consumption.
z The Super Bright Green source color devices are made
z Popular T-1 diameter package.
with Gallium Phosphide Green Light Emitting Diode.
z Electrostatic discharge and power surge could damage
z General purpose leads.
the LEDs.
z Reliable and rugged.
z Long life - solid state reliability.
z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs.
z Available on tape and reel.
z All devices, equipments and machineries must be
z 5V internal resistor.
electrically grounded.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAL0546
REV NO: V.6B
DATE: JAN/23/2015
PAGE: 1 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101029231
Selection Guide
Part No.
Dice
WP710A10SGD5V
Lens Type
Super Bright Green (GaP)
Viewing
Angle [1]
Iv (mcd) [2]
V= 5V
Min.
Typ.
2θ1/2
10
25
40°
Green Diffused
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Super Bright Green
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
565
nm
VF=5V
Super Bright Green
568
nm
VF=5V
Spectral Line Half-width
Super Bright Green
30
nm
VF=5V
IF
Forward Current
Super Bright Green
11.5
17.5
mA
VF=5V
IR
Reverse Current
Super Bright Green
10
uA
VR = 5V
Notes:
1. Wavelength: +/-1nm.
2. Wavelength value is traceable to the CIE127-2007 compliant national standards.
3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Green
Units
Power dissipation
85
mW
Forward Voltage
6
V
Reverse Voltage
5
V
Operating Temperature
-40°C To +70°C
Storage Temperature
-40°C To +85°C
Lead Solder Temperature [1]
260°C For 3 Seconds
Lead Solder Temperature [2]
260°C For 5 Seconds
Notes:
1. 2mm below package base.
2. 5mm below package base.
SPEC NO: DSAL0546
REV NO: V.6B
DATE: JAN/23/2015
PAGE: 2 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101029231
Super Bright Green
WP710A10SGD5V
SPEC NO: DSAL0546
REV NO: V.6B
DATE: JAN/23/2015
PAGE: 3 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101029231
PACKING & LABEL SPECIFICATIONS
WP710A10SGD5V
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL0546
REV NO: V.6B
DATE: JAN/23/2015
PAGE: 4 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101029231
SPEC NO: DSAL0546
REV NO: V.6B
DATE: JAN/23/2015
PAGE: 5 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101029231
SPEC NO: DSAL0546
REV NO: V.6B
DATE: JAN/23/2015
PAGE: 6 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101029231