Specifications

SUBMINIATURE SOLID STATE LAMP
Part Number: AM2520EJ/YD
Yellow
Features
Description
z Black case enhances contrast.
The Yellow source color devices are made with Gallium
z Vibration and shock resistant.
Arsenide Phosphide on Gallium Phosphide Yellow Light
z Housing UL rating:94V-0.
Emitting Diode.
z Housing material: type 66 nylon.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAD1632
REV NO: V.10B
DATE: JAN/17/2014
PAGE: 1 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1102005503
Selection Guide
Part No.
Dice
AM2520EJ/YD
Yellow (GaAsP/GaP)
Viewing
Angle [1]
Iv (mcd) [2]
@ 20mA
Lens Type
Min.
Typ.
2θ1/2
5
10
40°
Yellow Diffused
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Yellow
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Yellow
588
nm
IF=20mA
Spectral Line Half-width
Yellow
35
nm
IF=20mA
C
Capacitance
Yellow
20
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Yellow
2.1
2.5
V
IF=20mA
IR
Reverse Current
Yellow
10
uA
VR = 5V
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25°C
Parameter
Yellow
Units
Power dissipation
75
mW
DC Forward Current
30
mA
Peak Forward Current [1]
140
mA
5
V
Reverse Voltage
Operating/Storage Temperature
-40°C To +85°C
Lead Solder Temperature [2]
260°C For 3 Seconds
Lead Solder Temperature [3]
260°C For 5 Seconds
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
SPEC NO: DSAD1632
REV NO: V.10B
DATE: JAN/17/2014
PAGE: 2 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1102005503
Yellow
AM2520EJ/YD
SPEC NO: DSAD1632
REV NO: V.10B
DATE: JAN/17/2014
PAGE: 3 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1102005503
PACKING & LABEL SPECIFICATIONS
AM2520EJ/YD
Terms and conditions for the usage of this document
1.The information included in this document reflects representative usage scenarios and is intended
for technical reference only.
2.The part number, type, and specifications mentioned in this document are subject to future change
and improvement without notice. Before production usage customer should refer to the latest
datasheet for the updated specifications.
3.When using the products referenced in this document, please make sure the product is being
operated within the environmental and electrical limits specified in the datasheet. If customer usage
exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4.The information in this document applies to typical usage in consumer electronics applications.
If customer's application has special reliability requirements or have life-threatening liabilities,
such as automotive or medical usage, please consult with Kingbright representative for further
assistance.
5.The contents and information of this document may not be reproduced or re-transmitted without
permission by Kingbright.
6.All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAD1632
REV NO: V.10B
DATE: JAN/17/2014
PAGE: 4 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1102005503
SPEC NO: DSAD1632
REV NO: V.10B
DATE: JAN/17/2014
PAGE: 5 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.Liu
ERP: 1102005503