SURFACE MOUNT SUPER FAST RECTIFIER ES3A THRU ES3J VOLTAGE RANGE 50 to 600 Volts CURRENT 3.0 Ampere FEATURES • • • • • DO-214AB(SMC) Plastic package has underwrites laboratory Flammability Classification 94V-0 Glass passivated chip junction Built-in strain relief, Suoer Fast switching speed for high efficiency High temperature soldering guaranteed: 260℃/10 seconds MECHANICAL DATA • • • • Case: JEDED DO-214AB transfer molded plastic Terminals: Solder plated, solderable per MIL-STD-750 Method 2026 Polarity: Color band denotes cathode end Weight: 0.007 ounce, 0.25 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20%. SYMBOLS ES3A ES3B Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current at TL=100℃ Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) ES3G 400 280 400 ES3J 600 420 600 UNIT Volts Volts Volts Amps IFSM 100 Amps VF IR Typical Reverse Recovery Time Test conditions IF =0.5A, IR =1.0A, IRR =0.25A trr Typical Junction Capacitance (Measured at 1.0MHz and applied reverse voltage of 4.0V) CJ Storage Temperature Range ES3E 300 210 300 3.0 Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage per element TA = 125℃ Operating Junction Temperature Range ES3D 200 140 200 I(AV) Maximum Instantaneous Forward Voltage @ 3.0A Typical Thermal Resistance (Note 1) ES3C 150 105 150 0.95 1.25 5.0 300 1.7 µA 35 45 RθJA RθJL TJ TSTG Notes: 1. Thermal resistance from Junction to ambient and from junction to lead mounted on P.C.B. with 0.3”×0.3”(8.0mm × 8.0mm) copper pad areas. Web Site: www.hkmic.com nS 30 55 17 (-55 to +150) (-55 to +150) Volts pF ℃/W ℃ ℃ SURFACE MOUNT SUPER FAST RECTIFIER ES3A THRU ES3J VOLTAGE RANGE 50 to 600 Volts CURRENT 3.0 Ampere FIG.1-TYPICAL FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK DERATING CURVE FORWARD SURGE CURRENT PEAK FORWARD SURGE 3.0 Single Phase Half Wave 60Hz Inductive or Resistive Load 1.0 0.375″(9.5mm) Lead Length 150 8.3ms Single Half Sine-Wave CURRENT, (A) 2.0 (A) AVERAGE FORWARD CURRENT, RATING AND CHRACTERISTIC CURVES ES3A THRU ES3J (JEDEC Method) Tj = Tjmax 100 50 1 Cycle 0 0 50 25 100 75 175 150 125 0 1 2 AMBIENT TEMPERATURE, (° C) 4 6 8 10 40 20 60 100 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 1% Duty Cycle 0.01 1.0 (μA) TJ =25° C Pulse Width=300us 0.1 10 INSTANTANEOUS REVERSE CURRENT, -3 G 3J 3E ES ES ES 3A- 3D 1.0 (A) INSTANTANEOUS FORWARD CURRENT, 10 TJ =125° C 0.1 TJ =25℃ 0.01 0 0.001 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 20 40 60 80 120 100 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,(pF) 1000 F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC TRR 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE +0.5A (-) 100 (+) 25 Vdc (approx.) (-) TJ =25° C f=1MHz Vsig=50mVp-p D.U.T. 1Ω NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A ES3A-ES3D ES3E-ES3J 10 0.1 1.0 10 REVERSE VOLTAGE,(V) 100 NOTES : 1.Rise Time=7ns max. Input Impedance= 1 megohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms Web Site: www.hkmic.com 1cm SET TIME BASE FOR 50/100ns/cm