MERITEK Aluminum Electrolytic Capacitors

SS Series
Aluminum Electrolytic Capacitors
(85°C,5mmL)
MERITEK
FEATURES

For general purposes series with 5mm height.
SPECIFICATIONS
Item
Characteristic
Operating Temp Range
- 40 ~ +85C
Rated Working Voltage
4 ~ 50VDC
Capacitance Tolerance
(120Hz 20C)
 20%(M)
I  0.01CV or 3 (A)
Leakage Current
I : Leakage Current (A)
C : Rated Capacitance(F)
V : Working Voltage (V)
(20C)
*Whichever is greater after 2 minutes
Surge Voltage
W.V.
4
6.3
10
16
25
35
50
(20C)
S.V.
5
8
13
20
32
44
63
Dissipation Factor ( tan  )
(120Hz 20C)
W.V.
4
6.3
10
16
25
35
50
tan 
0.35
0.24
0.20
0.16
0.14
0.12
0.10
Low Temperature Stability
Load Life
Shelf Life
Impedance ratio at 120Hz
Rated Voltage (V)
4
6.3
10
16
25
35
50
-25C / +20C
7
4
3
2
2
2
2
-40C / +20C
15
8
6
4
4
3
3
After 1000 hours application of W.V. and +85C ripple current value , the capacitor shall meet
the following limits. ( DC + ripple peak voltage  rated working voltage )
Capacitance Change
 20% of initial.
Dissipation Factor
 200% of initial specified value
Leakage Current
 initial specified value
At +85C no voltage application after 1000 hours the capacitor shall meet the limits for load life
characteristics. ( with voltage treatment )
PART NUMBER S YSTEM
DIMENSIONS (mm)
SS 35V 100 M TR 5x5
Meritek Series
Rated Voltage
Rated Capacitance
Express in micro farad(uF), First two digits are
significant figures, Third digit denotes number of
zeros. ‘R’ denotes decimal point for values less
than 10uF
Tolerance
M - 20%
Package
Code
TA
TR
Tape & Ammo Tape & Reel
Blank
Case size – (D) Diameter x (L) Length in mm (Optional)
D
F
d
a
4
1.5
0.45
1.0
5
2.0
0.45
1.0
6.3
2.5
0.45
1.0
8
2.5
0.45
1.0
Rev. 7a
Aluminum Electrolytic Capacitors
SS Series
(85°C,5mmL)
MERITEK
CASE SIZE & MAX RIPPLE CURRENT
Cap. V
(uF) Item
0.1
0.15
0.22
0.33
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
220
330
4
DxL R.C.
6.3
DxL R.C.
10
DxL
R.C.


4x5
17
 4x5
19
4x5
21
 4x5
24
4x5
26
4x5 24
4x5
29
4x5(5x5) 31(36)
4x5 29 4x5(5x5) 35(40) 4x5(5x5) 38(44)
4x5 35
5x5
48 5x5(6.3x5) 50(60)
5x5 47 6.3x5
65
6.3x5
70
6.3x5 65 6.3x5
80 6.3x5(8x5) 90(100)
6.3x5 100 8x5
140
8x5
150
8x5 140 8x5
170
Case size
: DxL
Max. ripple current
: mA(rms) 85C
50
16
25
35
DxL
R.C.
DxL
R.C.
DxL
R.C.
DxL

4x5

4x5

4x5

4x5

4x5

4x5

4x5

4x5

4x5
13
4x5

4x5
14
4x5
16
4x5
4x5
16
4x5
17
4x5
19
4x5
4x5
19
4x5
21
5x5
26
6.3x5
4x5
24
4x5
25
5x5
31
6.3x5
5x5
33
5x5
35
6.3x5
44
6.3x5
5x5
40 5x5(6.3x5) 43(49)
6.3x5
55 6.3x5(8x5)
5x5(6.3x5) 49(55)
6.3x5
60
6.3x5(8x5) 65(75)
8x5
6.3x5
65 6.3x5(8x5) 70(85)
8x5
90
6.3x5
80
8x5
100
6.3x5(8x5) 100(110)
8x5
120
(mm)
120Hz
R.C.
3
4
4
5
6
8
9
12
14
17
20
32
39
48
60(70)
85
All blank voltage on sleeve marking is the same voltage as “” point to.
Rev. 7a
SS Series
Aluminum Electrolytic Capacitors
(85°C,5mmL)
MERITEK
TAPING SPECIFICATION


Lead taping is designed for automatic insertion equipment.
Capacitors with case size of 18mm x 35.5mm or smaller are available in taping type.
DIMENSIONS (Ø4~ Ø10)
Item
Symbol
Case Size
4x5
5 x 5 6.3x5 8 x 5
4x7
5 x 7 6.3x7 8 x 7 5 x 11 6.3x11 8 x 11.5 10x12.5 10x16 10x18
0.45
0.5
10x20
Tolerance
Lead wire diameter
d
Body height
A
Intervals of bodies
P
12.7
±1.0
Intervals of punched
holes
P0
12.7
±0.2
6.0
8.0
12.5
13
14
0.6
±0.05
17.5 19.5 21.5
MAX
3.85
Distance between
holes and lead wire
P1
5.35 5.1 5.1
5.6
Distance between
holes and bodies
5.35 5.1
5.35 5.1 5.1
5.6
5.1
±0.7
5.1
5.35 5.1 4.6 5.35 5.1
P2
F
6.35
2.0 2.5
2.5
2.0 2.5
2.5
Fig 1.
Fig 4.
Fig 2.
Fig 3.
4.6
±1.0
Fig 1.
Fig 4.
5.0
Distance between
lead and lead
Remark
+0.8
-0.2
2.5
Fig 2.
F1:5.0
+0.5
-1.0
1.5
2.0 2.5 2.5 1.5
Fig 3.
F1:5.0
2.0 2.5 3.5 2.0 2.5 3.5
+0.5
-1.0
Base tape width
W
W0
18.0
±0.5
12.5
MIN
Deviation between
holes and base tape
W1
9.0
±0.5
Deviation between
adhesive and base
tape
W2
1.5
MAX
Adhesive tape width
17.5
18.5
20.0
17.5
18.5
18.5
18.5
Distance between
body bottom and tape
center
H
Lead wire clinched
height
H0
Distance between
body top and tape
center
H1
Punched hole
diameter
D0
4.0
±0.3
Length of not good
lead slit
L
11.0
MAX
Base and adhesive
tape thickness
t
0.6
±0.3
Deviation of body
alignment
∆h
0
±2.0
Deviation of body
alignment
∆h1
0
±1.0
±0.5
16.0
24.5
Fig 1.
Fig 4.
Fig 2.
Fig 3.
±0.5
27.5
32.5
33.0 36.0 38.0 41.0
MAX
Rev. 7a
SS Series
Aluminum Electrolytic Capacitors
(85°C,5mmL)
MERITEK
DIMENSIONS (Ø12.5~ Ø18)
Item
12.5 x 20
Lead wire diameter
d
Body height
A
Intervals of bodies
P
Intervals of punched
holes
P0
Distance between
holes and lead wire
P1
Distance between
holes and bodies
Distance between
lead and lead
Base tape width
Adhesive tape width
Deviation between
holes and base tape
Deviation between
adhesive and base
tape
Case Size
Symbol
12.5 x 25
12.5 x 30
16 x 25
16 x 31.5
0.6
21.5
26.5
16 x 35.5 18 x 35.5
0.8
31.5
26.5
15.0
33
37.0
37.0
3.75
5.0
±0.7
±1.0
+0.8
-0.2
7.5
W
W0
18.0
±0.5
15.0
MIN
W1
9.0
±0.5
W2
1.5
MAX
Distance between
body bottom and tape
center
H
Distance between
body top and tape
center
H1
Punched hole
diameter
D0
4.0
±0.3
Length of not good
lead slit
L
11.0
MAX
t
0.6
±0.3
∆h
0
±2.0
∆h1
0
±1.0
Base and adhesive
tape thickness
Deviation of body
alignment
Deviation of body
alignment
16.5
40.5
45.5
18.5
50.5
46.5
Fig 5.
Fig 6.
±0.2
7.5
F
MAX
±1.0
15.0
P2
Remark
±0.05
30.0
5.0
Tolerance
53.5
±0.5
56.5
56.5
Fig 5.
Fig 6.
MAX
Rev. 7a
Aluminum Electrolytic Capacitors
SS Series
(85°C,5mmL)
MERITEK
Rev. 7a
Aluminum Electrolytic Capacitors
SS Series
(85°C,5mmL)
MERITEK
SOLDERABILITY
Capacitor lead wire is dipping into the oven, and then, dipping in 245±3℃, solder liquid for 3±0.5 seconds, the substance is above the liquid
solder 2mm, the dipping lead must be adherent 95% fresh tin at least.
RESISTANCE TO SOLDERING HEAT
Put capacitor lead wire to dip 260±5℃ in solder liquor away the body 2mm, after 10±1 seconds taken out, after 2 hours in room
temperature, should do final measurements, the values are following:
(A) Capacitance change: ≦ ±10% of initial value
(B) Dissipation factor: ≦ initial specified value
(C) Leakage current: ≦ initial specified value
(D) Visual: No damage
Rev. 7a