MERITEK Aluminum Electrolytic Capacitors

RFL Series
Aluminum Electrolytic Capacitors
(High R.C., Long Life)
MERITEK
FEATURES
 Endurance 105°C 8,000 to 10,000 hours.
 Suitable for electronic ballast, adaptor and switching power
SPECIFICATIONS
Item
Characteristic
Operating Temp Range
- 40 ~ +105C
- 25 ~ +105C
Rated Working Voltage
160 ~ 400VDC
450VDC
Capacitance Tolerance
(120Hz 20C)
 20%(M)
I  0.06CV+10 (uA)
Leakage Current
I : Leakage Current (A)
C : Rated Capacitance(F)
V : Working Voltage (V)
(20C)
*After 2 minutes
Surge Voltage
W.V.
160
200
250
350
400
450
(20C)
S.V.
200
250
300
400
450
500
Dissipation Factor ( tan  )
(120Hz 20C)
W.V.
160
200
250
350
400
450
tan 
0.15
0.15
0.15
0.24
0.24
0.24
Low Temperature Stability
Impedance ratio at 120Hz
Rated Voltage (V)
160~250
350~400
450
-25C / +20C
3
6
6
-40C / +20C
4
6
-
After hours application (D=10mm 8000hrs, D ≥12.5mm 10000hrs) of W.V. and +105C ripple
current value, the capacitor shall meet the following limits. ( DC + ripple peak voltage  rated
working voltage )
Load Life
Shelf Life
Capacitance Change
 20% of initial value.
Dissipation Factor
 200% of initial specified value
Leakage Current
 initial specified value
At +105C no voltage application after 1000 hours, the capacitor shall meet the limits for load life
characteristics. ( with voltage treatment )
DIMENSIONS (mm)
PART NUMBER SYSTEM
RFL
160V 101 M TA 16x25
Meritek Series
Rated Voltage
Rated Capacitance
Express in micro farad(uF), First two digits are
significant figures, Third digit denotes number of
zeros. ‘R’ denotes decimal point for values less
than 10uF
Tolerance
M - 20%
Package
Code
TA
Tape & Ammo
TR
Tape & Reel
Blank
Case size – (D) Diameter x (L) Length in mm (Optional)
D
F
d
a
10
5.0
0.6
1.5
12.5
5.0
0.6
1.5
16
7.5
0.8
1.5
18
7.5
0.8
1.5
Rev. 7a
Aluminum Electrolytic Capacitors
RFL Series
(High R.C., Long Life)
MERITEK
RIPPLE CURRENT COEFFICIENTS
Frequency(Hz)
W.V.
160~450
120
0.50
1k
10k
Multiplier
0.80
0.90
100k
Temperature(C)
Multiplier
65
1.80
75
1.65
85
1.50
95
1.25
Case size
Max. ripple current
250
DxL
10x16
R.C.
250
DxL
10x16
R.C.
250
DxL
10x20
R.C.
280
22
33
10x20
10x20
500
500
10x20
12.5x20
500
600
47
12.5x20
660
12.5x20
660
12.5x25
16x20
16x25
18x20
16x31.5
18x25
16x31.5
18x25
760
760
1120
1120
1360
1360
1400
1400
12.5x25
16x20
16x25
18x20
16x31.5
18x25
760
760
1120
1120
1360
1360
12.5x20
12.5x20
12.5x25
16x20
16x25
18x20
16x31.5
18x25
600
600
720
720
920
920
1200
1200
18x31.5
1500
18x31.5
1700
150
220
160
: DxL
(mm)
: mA(rms) 105C 100kHz
Cap. V
(uF) Item
10
100
200
DxL
10x16
R.C.
220
DxL
10x16
R.C.
220
DxL
10x20
R.C.
150
10
10x20
280
22
12.5x20
350
320
560
560
16x20
500
16x31.5
18x25
700
700
16x25
18x20
16x31.5
18x25
660
660
850
850
280
430
430
430
640
640
840
840
12.5x20
16x25
18x20
33
10x20
12.5x25
12.5x20
16x20
16x25
18x20
16x31.5
18x25
18x31.5
880
18x31.5
1000
18x35.5
1150
68
350
450
Cap. V
(uF) Item
6.8
47
1.00
1.00
CASE SIZE & MAX RIPPLE CURRENT
68
105
400
Rev. 7a
RFL Series
Aluminum Electrolytic Capacitors
(High R.C., Long Life)
MERITEK
TAPING SPECIFICATION


Lead taping is designed for automatic insertion equipment.
Capacitors with case size of 18mm x 35.5mm or smaller are available in taping type.
DIMENSIONS (Ø4~ Ø10)
Item
Symbol
Case Size
4x5
5 x 5 6.3x5 8 x 5
4x7
5 x 7 6.3x7 8 x 7 5 x 11 6.3x11 8 x 11.5 10x12.5 10x16
0.45
0.5
10x18 10x20
Tolerance
Lead wire diameter
d
Body height
A
Intervals of bodies
P
12.7
±1.0
Intervals of punched
holes
P0
12.7
±0.2
6.0
8.0
12.5
13
14
0.6
±0.05
17.5 19.5 21.5
MAX
3.85
Distance between
holes and lead wire
P1
5.35 5.1 5.1
5.6
Distance between
holes and bodies
5.35 5.1 5.1
5.35 5.1 5.1
5.6
±0.7
5.1
5.35 5.1 4.6 5.35 5.1
P2
F
6.35
2.0 2.5
2.5
2.0 2.5
2.5
Fig 1.
Fig 4.
Fig 2.
Fig 3.
4.6
±1.0
Fig 1.
Fig 4.
5.0
Distance between
lead and lead
Remark
+0.8
-0.2
2.5
Fig 2.
F1:5.0
+0.5
-1.0
1.5
2.0 2.5 2.5 1.5
Fig 3.
F1:5.0
2.0 2.5 3.5 2.0 2.5 3.5
+0.5
-1.0
Base tape width
W
W0
18.0
±0.5
12.5
MIN
Deviation between
holes and base tape
W1
9.0
±0.5
Deviation between
adhesive and base
tape
W2
1.5
MAX
Adhesive tape width
17.5
18.5
20.0
17.5
18.5
18.5
18.5
Distance between
body bottom and tape
center
H
Lead wire clinched
height
H0
Distance between
body top and tape
center
H1
Punched hole
diameter
D0
4.0
±0.3
Length of not good
lead slit
L
11.0
MAX
Base and adhesive
tape thickness
t
0.6
±0.3
Deviation of body
alignment
∆h
0
±2.0
Deviation of body
alignment
∆h1
0
±1.0
±0.5
16.0
24.5
Fig 1.
Fig 4.
Fig 2.
Fig 3.
±0.5
27.5
32.5
33.0 36.0 38.0 41.0
MAX
Rev. 7a
RFL Series
Aluminum Electrolytic Capacitors
(High R.C., Long Life)
MERITEK
DIMENSIONS (Ø12.5~ Ø18)
Item
12.5 x 20
Lead wire diameter
d
Body height
A
Intervals of bodies
P
Intervals of punched
holes
P0
Distance between
holes and lead wire
P1
Distance between
holes and bodies
Distance between
lead and lead
Base tape width
Adhesive tape width
Deviation between
holes and base tape
Deviation between
adhesive and base
tape
Case Size
Symbol
12.5 x 25
12.5 x 30
16 x 25
16 x 31.5
0.6
21.5
26.5
16 x 35.5 18 x 35.5
0.8
31.5
26.5
15.0
33
37.0
37.0
3.75
5.0
±0.7
±1.0
+0.8
-0.2
7.5
W
W0
18.0
±0.5
15.0
MIN
W1
9.0
±0.5
W2
1.5
MAX
Distance between
body bottom and tape
center
H
Distance between
body top and tape
center
H1
Punched hole
diameter
D0
4.0
±0.3
Length of not good
lead slit
L
11.0
MAX
t
0.6
±0.3
∆h
0
±2.0
∆h1
0
±1.0
Base and adhesive
tape thickness
Deviation of body
alignment
Deviation of body
alignment
16.5
40.5
45.5
18.5
50.5
46.5
Fig 5.
Fig 6.
±0.2
7.5
F
MAX
±1.0
15.0
P2
Remark
±0.05
30.0
5.0
Tolerance
53.5
±0.5
56.5
56.5
Fig 5.
Fig 6.
MAX
Rev. 7a
Aluminum Electrolytic Capacitors
RFL Series
(High R.C., Long Life)
MERITEK
Rev. 7a
Aluminum Electrolytic Capacitors
RFL Series
(High R.C., Long Life)
MERITEK
SOLDERABILITY
Capacitor lead wire is dipping into the oven, and then, dipping in 245±3℃, solder liquid for 3±0.5 seconds, the substance is above the
liquid solder 2mm, the dipping lead must be adherent 95% fresh tin at least.
RESISTANCE TO SOLDERING HEAT
Put capacitor lead wire to dip 260±5℃ in solder liquor away the body 2mm, after 10±1 seconds taken out, after 2 hours in room
temperature, should do final measurements, the values are following:
(A) Capacitance change: ≦ ±10% of initial value
(B) Dissipation factor: ≦ initial specified value
(C) Leakage current: ≦ initial specified value
(D) Visual: No damage
Rev. 7a