SSH Series Aluminum Electrolytic Capacitors (105°C,5mmL) MERITEK FEATURES Wide temperature range series with 5mm height. SPECIFICATIONS Item Characteristic Operating Temp Range - 55 ~ +105C Rated Working Voltage 4 ~ 50VDC Capacitance Tolerance (120Hz 20C) 20%(M) I 0.01CV or 3 (A) Leakage Current I : Leakage Current (A) C : Rated Capacitance(F) V : Working Voltage (V) (20C) ＊Whichever is greater after 2 minutes Surge Voltage W.V. 4 (20C) S.V. Dissipation Factor ( tan ) (120Hz 20C) W.V. tan Low Temperature Stability Load Life 6.3 10 16 25 35 50 5 8 13 20 32 44 63 4 6.3 10 16 25 35 50 0.37 0.28 0.24 0.20 0.16 0.13 0.12 Impedance ratio at 120Hz Rated Voltage (V) 4 6.3 10 16 25 35 50 -25C / +20C 6 3 3 2 2 2 2 -40C / +20C 12 8 5 4 3 3 3 After 1000 hours application of W.V. and +105C ripple current value , the capacitor shall meet the following limits. ( DC + ripple peak voltage rated working voltage ) Shelf Life Capacitance Change 25% of initial. Dissipation Factor 200% of initial specified value Leakage Current initial specified value At +105C no voltage application after 1000 hours the capacitor shall meet the limits for load life characteristics. ( with voltage treatment ) PART NUMBER S YSTEM DIMENSIONS (mm) SSH 10V 330 M TA 5x5 Meritek Series Rated Voltage Rated Capacitance Express in micro farad(uF), First two digits are significant figures, Third digit denotes number of zeros. ‘R’ denotes decimal point for values less than 10uF Tolerance M - 20% Package Code TA Tape & Ammo TR Tape & Reel Blank Case size – (D) Diameter x (L) Length in mm (Optional) D F d a 4 1.5 0.45 1.0 5 2.0 0.45 1.0 6.3 2.5 0.45 1.0 Rev. 7a SSH Series Aluminum Electrolytic Capacitors (105°C,5mmL) MERITEK CASE SIZE & MAX RIPPLE CURRENT Cap. V (uF) Item 0.1 4 DxL 6.3 R.C. DxL 10 R.C. DxL 16 R.C. DxL R.C. Case size : DxL (mm) Max. ripple current : mA(rms) 105C 120Hz 50 25 35 DxL R.C. DxL R.C. DxL R.C. 4x5 2 0.22 0.33 4x5 4x5 4 4 0.47 1.0 4x5 4x5 5 8 4x5 4x5 10 13 4x5 4x5 11 14 4x5 5x5 14 23 4x5 5x5 15 25 5x5 6.3x5 19 31 6.3x5 6.3x5 39 48 6.3x5 42 2.2 3.3 4.7 10 4x5 19 22 33 4x5 5x5 19 26 4x5 5x5 23 32 5x5 5x5 29 35 5x5 6.3x5 32 45 47 100 5x5 6.3x5 32 55 5x5 6.3x5 38 65 6.3x5 48 6.3x5 55 All blank voltage on sleeve marking is the same voltage as “” point to. Rev. 7a SSH Series Aluminum Electrolytic Capacitors (105°C,5mmL) MERITEK TAPING SPECIFICATION Lead taping is designed for automatic insertion equipment. Capacitors with case size of 18mm x 35.5mm or smaller are available in taping type. DIMENSIONS (Ø4~ Ø10) Item Symbol Case Size 4x5 5 x 5 6.3x5 8 x 5 4x7 5 x 7 6.3x7 8 x 7 5 x 11 6.3x11 8 x 11.5 10x12.5 10x16 0.45 0.5 10x18 10x20 Tolerance Lead wire diameter d Body height A Intervals of bodies P 12.7 ±1.0 Intervals of punched holes P0 12.7 ±0.2 6.0 8.0 12.5 13 14 0.6 ±0.05 17.5 19.5 21.5 MAX Fig 1. Fig 4. 3.85 Distance between holes and lead wire P1 5.35 5.1 5.1 5.6 Distance between holes and bodies 5.35 5.1 5.1 5.35 5.1 5.1 5.6 ±0.7 5.1 5.35 5.1 4.6 5.35 5.1 P2 F 6.35 2.0 2.5 2.5 2.0 2.5 2.5 Fig 2. Fig 3. 4.6 ±1.0 Fig 1. Fig 4. 5.0 Distance between lead and lead Remark +0.8 -0.2 2.5 Fig 2. F1:5.0 +0.5 Fig 3. F1:5.0 +0.5 -1.0 1.5 2.0 2.5 2.5 1.5 2.0 2.5 3.5 2.0 2.5 3.5 -1.0 Base tape width W W0 18.0 ±0.5 12.5 MIN Deviation between holes and base tape W1 9.0 ±0.5 Deviation between adhesive and base tape W2 1.5 MAX Adhesive tape width 17.5 18.5 20.0 17.5 18.5 18.5 18.5 Distance between body bottom and tape center H Lead wire clinched height H0 Distance between body top and tape center H1 Punched hole diameter D0 4.0 ±0.3 Length of not good lead slit L 11.0 MAX Base and adhesive tape thickness t 0.6 ±0.3 Deviation of body alignment ∆h 0 ±2.0 Deviation of body alignment ∆h1 0 ±1.0 ±0.5 16.0 24.5 Fig 1. Fig 4. Fig 2. Fig 3. ±0.5 27.5 32.5 33.0 36.0 38.0 41.0 MAX Rev. 7a SSH Series Aluminum Electrolytic Capacitors (105°C,5mmL) MERITEK DIMENSIONS (Ø12.5~ Ø18) Item Lead wire diameter d Body height A Intervals of bodies P Intervals of punched holes P0 Distance between holes and lead wire P1 Distance between holes and bodies Distance between lead and lead Case Size Symbol 12.5 x 20 12.5 x 25 21.5 26.5 12.5 x 30 16 x 25 16 x 31.5 31.5 26.5 33 0.6 16 x 35.5 18 x 35.5 0.8 15.0 37.0 3.75 5.0 ±0.7 ±1.0 +0.8 -0.2 7.5 Base tape width Adhesive tape width W W0 18.0 15.0 ±0.5 MIN Deviation between holes and base tape W1 9.0 ±0.5 Deviation between adhesive and base tape W2 1.5 MAX Distance between body bottom and tape center H Distance between body top and tape center H1 Punched hole diameter Length of not good lead slit 16.5 40.5 45.5 18.5 50.5 46.5 53.5 ±0.5 56.5 56.5 Fig 5. Fig 6. MAX D0 4.0 ±0.3 L 11.0 MAX t 0.6 ±0.3 Deviation of body alignment ∆h 0 ±2.0 Deviation of body alignment ∆h1 0 ±1.0 Base and adhesive tape thickness Fig 5. Fig 6. ±0.2 7.5 F MAX ±1.0 15.0 P2 Remark ±0.05 37.0 30.0 5.0 Tolerance Rev. 7a Aluminum Electrolytic Capacitors SSH Series (105°C,5mmL) MERITEK Rev. 7a Aluminum Electrolytic Capacitors SSH Series (105°C,5mmL) MERITEK SOLDERABILITY Capacitor lead wire is dipping into the oven, and then, dipping in 245±3℃, solder liquid for 3±0.5 seconds, the substance is above the liquid solder 2mm, the dipping lead must be adherent 95% fresh tin at least. RESISTANCE TO SOLDERING HEAT Put capacitor lead wire to dip 260±5℃ in solder liquor away the body 2mm, after 10±1 seconds taken out, after 2 hours in room temperature, should do final measurements, the values are following: (A) Capacitance change: ≦ ±10% of initial value (B) Dissipation factor: ≦ initial specified value (C) Leakage current: ≦ initial specified value (D) Visual: No damage Rev. 7a