RENESAS HD75160AP

HD75160A
Octal General Purpose Interface Bus Transceivers
REJ03D0308–0200Z
(Previous ADE-205-590 (Z))
Rev.2.00
Jul.16.2004
Description
The HD75160A is an 8 channel general purpose interface bus transceiver designed to meet the requirements of IEEE
standard 488-1978. The transceiver features driver outputs which can handle loads up to 48 mA of sink current if talk
Enable(TE) is high, the ports have the characteristics of open collector outputs when pull up enable(PE) is low, and of
three state outputs when PE is high. Taking TE low places the ports in the high impedance state. The device exhibits a
high impedance to the bus when VCC = 0 V since the bus terminating resistors are built in when combined with the
HD75161A mangement bus transceivers, the pair provides the complete 16 wire interface for the IEEE-488 bus.
Features
• Ordering Information
Part Name
HD75160AP
Package Type
DILP-20 pin
Package Code
DP-20N, -20NEV
Package
Abbreviation
P
—
20 VCC
B1 2
19 D1
B2 3
18 D2
B3 4
17 D3
B4 5
16 D4
B5 6
15 D5
B6 7
14 D6
B7 8
13 D7
B8 9
12 D8
GND 10
11 PE
GPIB I/O PORTS
TE 1
Rev.2.00, Jul.16.2004, page 1 of 12
TERMINAL I/O PORTS
Pin Arrangement
(Top view)
Taping Abbreviation
(Quantity)
HD75160A
Function Table
Drivers
Receivers
Input
D
Input
B
TE
PE
Output B
TE
PE
Output D
H
L
H
H
H
X
H
L
L
H
L
L
X
X
L
H
H
X
X
L
L
X
Z*1
Z*1
X
H
X
Z
H :
L :
X :
Z :
Note:
High level
Low level
Irrelevant
High impedance
1. This is the high impedance state of a normal three state output modified by the internal resistors to VCC and
ground.
Absolute Maximum Ratings
Item
Symbol
Rating
Unit
Supply Voltage
VCC
7
V
Input Voltage
Output Current
VIN
IOL
5.5
100
V
mA
Power Dissipation (Ta = 25°C)
Operating temperature range
PT
Topr
1150
0 to 70
mW
°C
Storage Temperature Range
Tstg
–65 to +150
°C
Note: 1. The absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two
of which may be realized at the same time.
Recommended Operating Conditions
Item
Supply Voltage
Symbol
Min
VCC
4.75
Typ
5.00
Max
5.25
V
Unit
Output Current
Bus Ports With Pull Ups Active
Terminal Ports
IOH
—
—
—
—
–5.2
–800
mA
µA
Output Current
Bus Ports
Terminal Ports
IOL
—
—
—
—
48
16
mA
Topr
0
—
70
°C
Operating Temperature
Rev.2.00, Jul.16.2004, page 2 of 12
HD75160A
Logic Diagram
PE
TE
D1
D2
D3
D4
D
R
B1
R
B2
R
B3
R
B4
D
D
D
TERMINAL
D5
D6
D7
D8
Rev.2.00, Jul.16.2004, page 3 of 12
GPIB
I/O
PORTS
D
R
B5
R
B6
R
B7
R
B8
D
D
D
HD75160A
DC Electrical Characteristics (Ta = 0 to 70°C)
Item
Symbol
VCC
Input Voltage
VIH
VIL
Input Clamp Voltage
Hysteresis
Bus
VIK
—
VT+ – VT– 0.4
IOutput Voltage
Input Current
2
—
Min
Max
Unit
Conditions
—
—
—
0.8
V
—
—
–1.5
—
V
V
II = –18 mA
Terminal VOH
Bus
2.7
2.5
—
—
—
—
V
IOH = –800 µA, TE at 0.8 V
IOH = –5.2 mA, PE and TE at 2 V
Terminal VOL
Bus
—
—
—
—
0.5
0.5
V
IOL = 16 mA, TE at 0.8 V
IOL = 48 mA, TE at 2 V
Terminal II
IIH
—
—
—
—
100
20
µA
VI = 5.5 V
VI = 2.7 V
Voltage At Bus Port
IIL
VI/O (bus)
—
2.5
—
—
–100
3.7
V
VI = 0.5 V
Driver
II(bus) = 0
Current Into Bus VCC ON
II/O (bus)
—
–1.3
—
—
–1.5
—
Disabled
Driver
II(bus) = –12 mA
VI(bus) = –1.5 V to 0.4 V
0
—
—
—
–3.2
+2.5
–3.2
Disabled
VI(bus) = 0.4 V to 2.5 V
VI(bus) = 2.5 V to 3.7 V
0
0.7
—
—
2.5
2.5
—
–15
—
—
40
–75
ICC
–25
—
—
60
–125
80
mA
CI/O (bus)
—
—
75
30
100
—
Port
Short circuit
Terminal IOS
Output Current
Supply Voltage
Bus
Busport Capacitance
Note:
mA
VI(bus) = 3.7 V to 5 V
VI(bus) = 5 V to 5.5 V
µA
mA
VCC = 0, VI(bus) = 0 V to 2.5 V
No Load, Receivers Low and Enabled
No Load, Drivers Low and Enabled
VCC = 5 V or 0 V, VI/O = 0 to 2 V,
f = 1 MHz
pF
1. VCC = 5 V, Ta = 25°C
Switching Characteristics (VCC = 5 V, Ta = 25°C)
Item
Propagation Delay
Time
Symbol
Input
Output
tPLH
tPHL
Terminal BUS
tPLH
tPHL
Output Enable Time tZH
Output Disable Time tHZ
—
—
14
14
20
20
BUS
Terminal —
—
12
16
TE
BUS
—
—
TE
CL = 30 pF
RL = 38.3 Ω to 2.3 V
20
22
2
CL = 30 pF
RL = 240 Ω to 5 V
25
13
35
22
3
CL = 15 pF
RL = 480 Ω to 0 V
—
—
22
22
35
32
Terminal —
—
20
12
30
20
—
—
23
19
32
30
—
15
22
—
13
20
Output Enable Time tZL
Output Disable Time tLZ
Output Pull up
Enable Time
Output Pull up
Disable Time
ten
PE
tdis
Rev.2.00, Jul.16.2004, page 4 of 12
BUS
ns
Conditions
1
Output Enable Time tZL
Output Disable Time tLZ
Output Enable Time tZH
Output Disable Time tHZ
Test
Min Typ Max Unit Circuit
CL = 15 pF
RL = 38.3 Ω to 2.3 V
4
CL = 15 pF
RL = 3 kΩ to 0 V
CL = 15 pF
RL = 280 Ω to 5 V
5
CL = 15pF
RL = 480 Ω to 0 V
HD75160A
Switching Time Test Method
1. tPLH, tPHL
2.3 V
PE
3V
R L=
38.3 Ω
D
Pulse
Generator
B
D
Output
R L=
50 Ω
C L=
30 pF
R
TE
3V
Waveforms-1
tr
tf
90 %
1.5 V
Input D
3V
90 %
1.5 V
10 %
10 %
t PLH
0V
t PHL
VOH
Output B
2V
0.8 V
VOL
Rev.2.00, Jul.16.2004, page 5 of 12
HD75160A
2. tPLH, tPHL
5V
Output
TE
R L=
240 Ω
B
Pulse
Generator
R
R L=
50 Ω
D
C L=
30 pF
D
Waveforms-2
tr
tf
90 %
1.5 V
Input B
3V
90 %
1.5 V
10 %
10 %
t PLH
0V
t PHL
VOH
Output D
1.5 V
1.5 V
VOL
Rev.2.00, Jul.16.2004, page 6 of 12
HD75160A
3. tZH, tHZ, tZL, tLZ
Output
3V
R L=
38.3 Ω
PE
S1
2.3 V
S3
D
B
D
C L=
15 pF
R
R L=
480 Ω
S2
TE
Pulse
Generator
R L=
50 Ω
Waveforms-3
tr
tf
90 %
1.5 V
Input TE
3V
90 %
1.5 V
10 %
Output B
S1 to 3 V
S2 Closed
S3 Open
10 %
t ZH
t HZ
90 %
Rev.2.00, Jul.16.2004, page 7 of 12
VOH
2V
0.3 V
t LZ
t ZL
Output B
S1 to GND
S2 Open
S3 Closed
0V
2.3 V
0.8 V
10 %
VOL
HD75160A
4. tZH, tHZ, tZL, tLZ
5V
Output
Pulse
Generator
S3
R L=
50 Ω
D
R
S1
3V
B
R L=
280 Ω
C L=
15 pF
D
R L=
3 kΩ
S2
Waveforms-4
tr
tf
Input TE
90 %
Output D
S1 to 3 V
S2 Closed
S3 Open
90 %
1.5 V
10 %
1.5 V
10 %
t ZH
Rev.2.00, Jul.16.2004, page 8 of 12
0V
t HZ
90 %
VOH
1.5 V
0V
t LZ
t ZL
Output D
S1 to GND
S2 Open
S3 Closed
3V
5V
1.5 V
10 %
VOL
HD75160A
5. ten, tdis
PE
Pulse
Generator
R L=
50 Ω
D
B
D
Output
C L=
15 pF
R L=
480 Ω
R
TE
3V
Waveforms-5
tr
tf
90 %
1.5 V
Input PE
10 %
10 %
t en
Output B
3V
90 %
1.5 V
0V
t dis
90 %
VOH
2V
VOL
Notes:
1. The pulse generator has the following characteristics:
PRR = 1 MHz, 50% duty cycle, tr≤ 6 ns, t f≤ 6 ns, Zout = 50 Ω
2. CL includes probe and jig capacitance.
3. All diodes are 1S2074(H).
Rev.2.00, Jul.16.2004, page 9 of 12
HD75160A
Characteristics Of Driver And Receiver
5
(b) Driver Output
Ta = 25 °C
V CC = 5.25 V
5.00 V
4.75 V
4
3
2
1
0
0
–20
–40
–60
0.5
Low Level Output Voltage VOL (V)
High Level Output Voltage VOH (V)
(a) Driver Output
0.4
0.1
0
–80 –100
0
2
1
0
–10
–20
–30
–40
–50
High Level Output Current IOH (mA)
Rev.2.00, Jul.16.2004, page 10 of 12
20
30
40
50
Low Level Output Current IOL (mA)
Low Level Output Voltage VOL (V)
High Level Output Voltage VOH (V)
V CC = 5.25 V
5.00 V
4.75 V
0
10
(d) Receiver Output
Ta = 25 °C
3
V CC = 5.00 V
V CC = 5.25 V
0.2
(c) Receiver Output
4
V CC = 4.75 V
0.3
High Level Output Current IOH (mA)
5
Ta = 25 °C
0.5
0.4
Ta = 25 °C
V CC = 4.75 V
0.3
V CC = 5.00 V
V CC = 5.25 V
0.2
0.1
0
0
12
18
24
30
Low Level Output Current IOL (mA)
HD75160A
High Level Output Voltage VOUT (V)
(e) Input / Output Characteristics at Receiver
5
VCC = 5 V
Ta = 25 °C
4
3
VT –
2
VT +
1
0
0
0.4
0.8
1.2
1.6
2.0
High Level Output Current VIN (V)
Rev.2.00, Jul.16.2004, page 11 of 12
HD75160A
Package Dimensions
As of January, 2003
Unit: mm
24.50
25.40 Max
1
7.00 Max
11
6.30
20
10
2.54 ± 0.25
0.51 Min
1.27 Max
0.48 ± 0.10
2.54 Min 5.08 Max
1.30
0.89
7.62
+ 0.11
0.25 – 0.05
0˚ – 15˚
Package Code
JEDEC
JEITA
Mass (reference value)
DP-20N
—
Conforms
1.26 g
Unit: mm
24.50
25.40 Max
1
7.00 Max
11
6.30
20
10
1.30
2.54 ± 0.25
*0.48 ± 0.08
0.51 Min
1.27 Max
2.54 Min 5.08 Max
0.89
7.62
*0.25 ± 0.06
0˚ – 15˚
*NI/Pd/AU Plating
Rev.2.00, Jul.16.2004, page 12 of 12
Package Code
JEDEC
JEITA
Mass (reference value)
DP-20NEV
—
Conforms
1.26 g
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
http://www.renesas.com
RENESAS SALES OFFICES
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501
Renesas Technology Europe Limited.
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom
Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900
Renesas Technology Europe GmbH
Dornacher Str. 3, D-85622 Feldkirchen, Germany
Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11
Renesas Technology Hong Kong Ltd.
7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2375-6836
Renesas Technology Taiwan Co., Ltd.
FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
© 2004. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .1.0