RENESAS HD29050P

HD29050
Dual Differential Line Drivers/ReceiversWith 3 State Outputs
REJ03D0304–0300Z
(Previous ADE-205-034A (Z))
Rev.3.00
Jul.16.2004
Description
The HD29050 features differential line drivers/receivers with three state output designed to meet the spec of EIA RS422A and 423A. Each device has two drivers/receivers in a 16 pin package.
The device becomes in enable state when active high for a driver and active low for a receiver.
Features
Driver
• Built in current restriction when short circuit
• Power up/down protection.
• High output current
IOH = –40 mA
IOL = 40 mA
Receiver
• Input hysteresis (Typ. 50 mV)
• In phase input voltage ±200 mV of input sensitivity in the range –7 to +12 V.
• Ordering Information
Part Name
HD29050P
Package Type
DILP-16 pin
Package Code
DP-16E, -16FV
Package
Abbreviation
P
—
Pin Arrangement
R1B 1
16 VCC
R1A 2
15 D1A
R1Y 3
14 D1Y
R Enable 4
13 D1Z
R2Y 5
12 D Enable
R2A 6
11 D2Z
R2B 7
10 D2Y
GND 8
9 D2A
(Top view)
Rev.3.00, Jul.16.2004, page 1 of 13
Taping Abbreviation
(Quantity)
HD29050
Function Table
Drivers
Receivers
Input A
L
H
Output Y Output Z
Differential Input A – B
L
H
VID ≥ 0.2 V
H
X
H
L
H
Z
H
L
Z
X
?
:
:
:
:
:
Enable
L
Z
Enable
Output Y
L
H
–0.2 V < VID < 0.2 V
VID ≤ –0.2 V
L
H
?
Z
X
H
Z
High level
Low level
High impedance
Immaterial
Irrelevant
Absolute Maximum Ratings
Item
Symbol
Ratings
Unit
Supply Voltage*1
Input Voltage A, B*3
VCC
VIN
7
±25
V
V
Differential Input Voltage*2*3
Output Current*3
VID
IO
±25
50
V
mA
Enable Input Voltage
Input Voltage*4
VIE
VIN
5.5
5.5
V
V
Output Applied Voltage*4*5
Operating Temperature Range
VO
Topr
–1.0 to 7.0
0 to 70
V
°C
Storage Temperature Range
Tstg
–65 to 150
°C
Notes: 1. All voltage values except for differential input voltage are with respect to network ground terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting
input.
3. Only receiver
4. Only driver
5. Z state
6. The absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two
of which may be realized at the same time.
Recommended Operating Conditions
Item
Symbol
Min
Typ
Max
Unit
Supply Voltage
In Phase Input Voltage*1
VCC
VIC
4.75
–7.0
5.0
—
5.25
12
V
V
Differential Input Voltage*1
Enable Input Voltage
VID
VIE
–6.0
0
—
—
6.0
5.25
V
V
Input Voltage*2
Operating Temperature
VIN
Topr
0
0
—
25
5.25
70
V
°C
Notes: 1. Only receiver
2. Only driver
Rev.3.00, Jul.16.2004, page 2 of 13
HD29050
Electrical Characteristics (Ta = 0 to +70°C)
Driver
Item
Symbol
Min
Typ
Max
Unit
Conditions
Input Voltage
VIHD
VILD
2.0
—
—
—
—
0.8
V
V
Input Clamp Voltage
Output Voltage
VIKD
VOHD
—
2.5
—
—
–1.5
—
V
V
VCC = 4.75 V, II = –18 mA
VCC = 4.75 V, IOH = –20 mA
VOLD
2.4
—
—
—
—
0.45
V
V
VCC = 4.75 V, IOH = –40 mA
VCC = 4.75 V, IOL = 20 mA
IOZD
—
–100
—
—
0.5
100
V
µA
VCC = 4.75 V, IOL = 40 mA
VCC = 5.25 V, VO = 0.5 V,
Enable = 0.8 V
–100
—
100
µA
IO (Off)
—
—
–100
µA
VCC = 5.25 V, VO = 2.7 V,
Enable = 0.8 V
VCC = 0 V, VO = –0.25 V
IID
—
—
—
—
–100
100
µA
µA
VCC = 0 V, VO = 6.0 V
VCC = 5.25 V, VI = 5.25 V
IIHD
IILD
—
—
—
—
20
–360
µA
µA
VCC = 5.25 V, VI = 2.7 V
VCC = 5.25 V, VI = 0.4 V
∆ |VOC|
|VOD2|
—
2.0
—
—
0.4
—
V
V
∆ |VOD|
IOSD
—
–30
—
—
0.4
–150
V
mA
Output Leak Current
Input Current
Differential Output Voltage
1
Short Circuit Output Current*
Rev.3.00, Jul.16.2004, page 3 of 13
VCC = 5.25 V, VO = 0 V
HD29050
Electrical Characteristics (Ta = 0 to +70°C)
Receiver
Item
Differential Input Threshold
Voltage*2
Symbol
VTHR
Min
Typ
Max
Unit
—
—
0.2
V
–0.2
—
—
V
Conditions
VO≥ 2.7 V
–7.0 V < VIC < 12 V
VO≤ 0.45 V
–7.0 V < VIC < 12 V
Input Current
IIBR
—
—
—
—
1.0
–0.8
mA
mA
VIN≤=V12 V, 0 V
VIN≤=V–7 V, 0 V
Output Voltage
VOHR
2.7
—
—
V
VOLR
—
—
0.45
V
VCC = 4.75 V, IO = –400 mA
VID = 0.4 V,–7.0 V < VICM < 12 V
VCC = 4.75 V, IO = 8.0 mA
VID = –0.4 V,
–7.0 V < VICM < 12 V
IOZR
–100
—
100
mA
–100
—
100
mA
mA
Output Leak Current
≤ 5.25 V
CC≤ 5.25 V
CC
VCC = 5.25 V, VO = 0.4 V
VID = 3.0 V, Enable = 2.0 V
VCC = 5.25 V, VO = 2.4 V
VID = –3.0 V, Enable = 2.0 V
Short Circuit Output Current*1
IOSR
–15
—
–85
Input Voltage
VIHE
2.0
—
—
V
Input Current
VILE
IILE
—
—
—
—
0.8
–100
V
µA
VCC = 5.25 V, VIL = 0.4 V
IIHE
IIE
—
—
—
—
20
100
µA
µA
VCC = 5.25 V, VIH = 2.7 V
VCC = 5.25 V, VIH = 5.25 V
VIKE
—
—
–1.5
V
VCC = 4.75, II = –18 mA
Input Clamp Voltage
VCC = 5.25 V, VO = 0 V
VID = 3.0 V
Supply
Item
Symbol
Min
Typ
Max
Unit
Conditions
Supply Current
ICC
—
55*3
80
mA
VCC = 5.25 V
Notes: 1. Not more than one output should be shorted at a time, and duration of the short circuit should not exceed one
second.
2. In this table, only the threshold voltage is expressed in algebra.
3. All typical values are at VCC = 5 V, Ta = 25°C.
Rev.3.00, Jul.16.2004, page 4 of 13
HD29050
Switching Characteristics (Ta = 25°C, VCC = 5 V)
Driver
Item
Propagation Delay Time
Symbol
Min
Typ
Max
Unit
tPLHD
—
—
20
ns
tPHLD
—
—
20
ns
Conditions
CL = 30 pF, RL = 75 Ω to GND
RL = 180 Ω to VCC
CL = 30 pF, RL = 75 Ω to GND
RL = 180 Ω to VCC
Propagation Delay Time
Difference
Output Enable Time
tSKD*1
—
—
4
ns
tZHD
—
—
20
ns
CL = 30 pF, RL = 75 Ω to GND
RL = 180 Ω to VCC
CL = 30 pF, RL = 75 Ω to GND
Output Disable Time
tZLD
tHZD
—
—
—
—
35
20
ns
ns
CL = 30 pF, RL = 180 Ω to VCC
CL = 10 pF, RL = 75 Ω to GND
tLZD
—
—
25
ns
CL = 10 pF
Receiver
Item
Propagation Delay Time
Symbol
Min
tPLHR
—
Typ
—
Max
40
Unit
ns
CL = 15 pF
Output Enable Time
tPHLR
tZHR
—
—
—
—
40
20
ns
ns
CL = 15 pF
CL = 15 pF, RL = 5 KΩ to GND
Output Disable Time
tZLR
tHZR
—
—
—
—
25
30
ns
ns
CL = 15 pF, RL = 2 KΩ to VCC
CL = 15 pF, RL = 5 KΩ to GND
RL = 2 KΩ to VCC
tLZR
—
—
30
ns
Note:
1. tSKD = |tPLHD – tPHLD|
Rev.3.00, Jul.16.2004, page 5 of 13
Conditions
HD29050
DC Test (|VOD2|, ∆ |VOD|, VOC, ∆ |VOC|)
|VOD2|, ∆ |VOD| Test
50 Ω
Output Y
VOD 2
Output Z
50 Ω
VOC, ∆ |VOC| Test
50 Ω
Y
R
Z
Note:
50 Ω
VOC
|VOD| and ∆ |VOC| indicate the differences of voltage from the former states when Y and Z outputs are
inversed.
∆ |VOD| = ||VOD2| – |VOD2||
∆ |VOC| = |VOC – VOC|
1. tPLHD, tPHLD
Test circuit
3V
Enable
5V
Input
Pulse
Generator
*1
Output
A
R L=
180 Ω
Y
Z
C L=
30 pF
*2
Rev.3.00, Jul.16.2004, page 6 of 13
R L=
75 Ω
HD29050
Waveforms
tr
Input A
10 %
tf
90 %
1.3 V
3V
90 %
1.3 V
10 %
t PLHD
0V
t PHLD
VOH
Output Y
1.3 V
1.3 V
VOL
t PLHD
t PHLD
VOH
1.3 V
Output Z
1.3 V
t SKD
t SKD
2. tZHD, tZLD, tHZD, tLZD
Test circuit
Input
Pulse
Generator
5V
Enable
*1
3 V or GND
A
Output
R L=
180 Ω
Y
Z
C L = 30 pF
or 10 pF
*2
Rev.3.00, Jul.16.2004, page 7 of 13
*3
R L=
75 Ω
VOL
HD29050
Waveforms
tf
tr
Input
Enable
10 %
3V
90 %
1.3 V
90 %
1.3 V
10 %
0V
t HZD
t ZHD
0.5 V
1.3 V
VOH
VOL
Output
t LZD
t ZLD
VOH
1.3 V
0.5 V
3. tPLHR, tPHLR
Test circuit
Enable
Input
Pulse
Generator
*1
A
B
1.5 V
Rev.3.00, Jul.16.2004, page 8 of 13
Output
C L=
15 pF
*2
VOL
HD29050
Waveforms
tr
Input A
10 %
tf
90 %
1.5 V
90 %
1.5 V
t PLHR
3V
10 %
0V
t PHLR
VOH
Output Y
1.3 V
1.3 V
VOL
4. tZHR, tZLR, tHZR, tLZR
Test circuit
Input
5V
Pulse
Generator
S1 *4
Enable
*1
Va
+1.5 V or -1.5 V
Output
R L=
2 kΩ
A
B
C L=
15 pF
*2
R L=
5 kΩ
S2 *4
Rev.3.00, Jul.16.2004, page 9 of 13
HD29050
Waveforms
tf
tr
Input
Enable
10 %
90 %
1.5 V
90 %
1.5 V
3V
10 %
0V
t HZR
t ZHR
0.5 V
1.5 V
VOH
VOL
Output Y
t LZR
t ZLR
VOH
1.5 V
0.5 V
Notes:
1. The pulse generator has the following characteristics:
PRR = 1 MHz, 50% duty cycle, tr = tf = 6.0 ns.
2. CL includes probe and jig capacitance.
3. 75 Ω connected between the pin and GND at tZHD tHZD test.
180 Ω connected between the pin and GND at tZHD tHZD test.
4. At tHZR, tLZR test, S1 and S2 are closed.
At tZHR test, S1 is open and S2 is closed.
At tZLR test, S1 is closed and S2 is open.
Rev.3.00, Jul.16.2004, page 10 of 13
VOL
HD29050
Main Characteristics
Output Characteristics (High level)
[Driver]
V CC = 5.25 V
5.00 V
4.75 V
4
3
2
1
0
0
–40
Ta = 25 °C
V CC = 5.25 V
0.8
V CC = 5.00 V
0.6
0.4
V CC = 4.75 V
0.2
0
–80 –120 –160 –200
0
20
40
60
80
100
Output Current (IOH) [mA]
Output Current (IOL) [mA]
Output Characteristics (High level)
[Receiver]
Output Characteristics (Low level)
[Driver]
5
Output Voltage (VOH) [V]
1.0
Output Voltage (VOL) [V]
Ta = 25 °C
1.0
Ta = 25 °C
V CC = 5.25 V
5.00 V
4.75 V
4
3
2
1
0
0
–20
–40
–60
–80 –100
Output Current (IOH) [mA]
Rev.3.00, Jul.16.2004, page 11 of 13
Output Voltage (VOL) [V]
Output Voltage (VOH) [V]
5
Output Characteristics (Low level)
[Driver]
Ta = 25 °C
0.8
V CC = 5.00 V
0.6
V CC = 4.75 V
0.4
0.2
V CC = 5.25 V
0
0
10
20
30
40
Output Current (IOL) [mA]
50
HD29050
Input / Output Characteristics
[Receiver]
Output Voltage (VOUT) [V]
5
VCC = 5 V
Ta = 25 °C
4
V IA = 0 V
3
2
VT –
VT +
1
0
0 –200 –100
0
100
200
Input Voltage (VU) [mV]
Rev.3.00, Jul.16.2004, page 12 of 13
HD29050
Package Dimensions
As of January, 2003
Unit: mm
19.2
20.32 Max
9
6.3
7.4 Max
16
1
8
0.48 ± 0.1
2.54 ± 0.25
2.54 Min 5.06 Max
0.51 Min
1.3
0.89
7.62
+ 0.1
0.25 – 0.05
0˚ – 15˚
Package Code
JEDEC
JEITA
Mass (reference value)
DP-16E
Conforms
Conforms
1.05 g
Unit: mm
19.2
20.32 Max
9
6.3
7.4 Max
16
1
8
*0.48 ± 0.08
2.54 Min 5.06 Max
2.54 ± 0.25
1.3
0.51 Min
0.89
7.62
*0.25 ± 0.06
0˚ – 15˚
*NI/Pd/AU Plating
Rev.3.00, Jul.16.2004, page 13 of 13
Package Code
JEDEC
JEITA
Mass (reference value)
DP-16FV
Conforms
Conforms
1.05 g
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
http://www.renesas.com
RENESAS SALES OFFICES
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501
Renesas Technology Europe Limited.
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom
Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900
Renesas Technology Europe GmbH
Dornacher Str. 3, D-85622 Feldkirchen, Germany
Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11
Renesas Technology Hong Kong Ltd.
7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2375-6836
Renesas Technology Taiwan Co., Ltd.
FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
© 2004. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .1.0