53259 - Micropac Industries

53259
POWER MOSFET OPTOCOUPLER
SPST NORMALLY CLOSED
Mii
MICROCIRCUITS DIVISION
Features:
Applications:














Hermetically Sealed 8-Pin Dual-In-Line
package
Normally Closed Contact
Performance over –55°C to +125°C Ambient
Temperature Range
±400 VDC Blocking Voltage in Bi-directional
Mode
AC/DC Switching
Maximum AC / DC Load Current: 0.12 A / 0.24 A
1500 VDC Withstand Test Voltage
Optically Isolated
1.5 A Output Surge Current
Same foot print as HSSR 7111 / Mii 53111




Satellite / Space Systems
Military / High Reliability Systems
Power Distribution Control
AC/DC Electromechanical or Reed Relay
Replacement
I/O Modules for Automated Test Equipment
Process Control
Telecom Applications
Medical Electronics
DESCRIPTION
The 53259 is a single channel power MOSFET optocoupler. Low on-resistance of the MOSFET outputs, combined
with 1500 VDC isolation between input and output, makes this optocoupler ideal for many solid state relay
applications. Operation is specified over the full military temperature range. The part is supplied in an eight-pin,
dual-in-line ceramic package, available in variety of quality levels from COTS to class K including any custom
screening requirements. The basic data sheet part is environmentally screened to H level in accordance with Table
C-IX of MIL-PRF-38534. For ordering part number; consult with Micropac factory for detail. The part is normally
shipped with gold plated leads, but lead finishes per MIL-PRF-38534 are available.
Functionally, the device operates as a single-pole, normally closed (1 Form B) solid state relay. The device is
actuated by an input current, which can be supplied from standard logic types such as open-collector TTL. The
input current biases a light emitting diode that is optically coupled to an integrated photovoltaic diode array. The
photovoltaic array powers control circuitry that operates the output MOSFETs.
Optimum switching of either AC or DC loads is provided by a configurable output. For AC loads, connection A in
Figure 1 must be used. Connection A will also switch DC loads but connection B, in Figure 1, provides DC-only
operation with the advantages of substantial reduction in on-resistance and twice the output current capability as
that obtained with connection A.
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION  905 E. Walnut St., Garland, TX 75040  (972) 272-3571  Fax (972) 494-2281
E-MAIL: [email protected]
05/06/2013 Rev D
www.micropac.com
Pg. 1 of 7
53259
Power MOSFET Optocoupler
___________________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Storage Temperature Range ..................................................................................................................-65°C to +150°C
Operating Ambient Temperature - TA .....................................................................................................-55°C to +125°C
Junction Temperature - TJ........................................................................................................................................ 150°C
Lead Solder Temperature (1.6mm below seating plane for 10 seconds) ............................................................ 260C
Average Input Current - IF ........................................................................................................................................20 mA
Peak Repetitive Input Current - IFpk (Pulse Width < 100ms; duty cycle < 50%) ..................................................40 mA
Peak Surge Input Current - IFPK surge (Pulse Width < 0.2ms; duty cycle < 0.1%) .......................................... 100 mA
Reverse Input Voltage - VR .................................................................................................................................... 5 V
Output Current
Connection A – IO.......................................................................................................................................... 0.12 A
Connection B - IO .......................................................................................................................................... 0.24 A
Inrush Output Current
Connection A - IOpk surge … ........................................................................................................................... 1.5 A
Output Blocking Voltage
Connection A - VO .................................................................................................................................. ± 400 VDC
Connection B - VO ........................................................................................................................ 0 V to +400 VDC
Output Power Dissipation .............................................................................................................................. 500 mW
RECOMMENDED OPERATING CONDITIONS:
PARAMETER
SYMBOL
MIN
MAX
UNITS
Input Current (off)
IF (OFF)
5
20
mA
Input Voltage (on)
VF (ON)
0
0.6
VDC
TA
-55
+125
°C
Operating Temperature
Note: On state means contact closed. Off state means contact open.
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION  905 E. Walnut St., Garland, TX 75040  (972) 272-3571  Fax (972) 494-2281
E-MAIL: [email protected]
05/06/2013 Rev D
www.micropac.com
Pg. 2 of 7
53259
Power MOSFET Optocoupler
___________________________________________________________________________________________
ELECTRICAL SPECIFICATIONS
TA = -55C to +125C, unless otherwise specified.
Parameter
Output Blocking Voltage
Sym.
Min.
Typ.*
Max.
Units
VO(OFF)
400
----
----
V
Test Conditions
IF = 10 mA
IO = 10 A
IF = 0 mA, VIN = 28V
Output On-Resistance
----
(Connection A)
25
50

Output On-Resistance
12
25

Figure
3
IO = 240 mA
(pulse duration  30 ms)
IO (OFF)
----
0.2
10
A
VO(OFF) = 400 V
Input Forward Voltage
VF
1.0
1.2
1.9
V
IF = 10 mA
Input Reverse
Breakdown Voltage
VR
5.0
12
----
V
IR = 10 A
Output Leakage Current
3
IF = 0 mA, VIN = 28V
----
(Connection B)
IO = 120 mA
(pulse duration  30 ms)
R(ON)
Notes
RH  45%, t = 5 s
Input-Output Insulation
II-O
----
----
1.0
A
VI-O = 1500 VDC
4, 5
TA = 25C
Turn-On Time
tON
----
0.3
3.0
ms
Turn-Off time
tOFF
----
0.1
1.0
ms
IF = 0 mA, VIN = 200V
IO = 25 mA
IF = 10 mA, VIN = 200V
IO = 25 mA
3
Figure
3
3
Figure
3
* All typical values are at TA = 25ºC, unless otherwise specified.
Notes:
1. Maximum junction to case thermal resistance (JC) for the device is 15ºC/W, where case temperature (TC), is
measured at the center of the package bottom.
2. R(ON) is measured for the individual sections of Condition B, Pins 5 and 6 and Pins 7 and 8. Meeting these limits
guarantees the performance of Connection A.
3. During the pulsed R(ON), T(ON) T(OFF) measurements (IO duration < 30 ms), ambient (TA) and case temperature
(TC) are equal.
4. Pins 2 and 3 shorted together and pins 5 through 8 shorted together.
5. This is a momentary withstand test, not an operating condition.
6. Care should be taken not to exceed the maximum output power dissipation, maximum case temperature, and
maximum junction temperature when repetitively switching loads.
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION  905 E. Walnut St., Garland, TX 75040  (972) 272-3571  Fax (972) 494-2281
E-MAIL: [email protected]
05/06/2013 Rev D
www.micropac.com
Pg. 3 of 7
53259
Power MOSFET Optocoupler
___________________________________________________________________________________________
Terminal number
Terminal symbol
1
2
3
4
5
6
7
8
Connection A
(AC or DC load)
Conneciton B
(DC load only)
NC
V F+
V FNC
VONC
NC
VO+
NC
V F+
V FNC
V O+
V OV OV O+
NC = No connection
CONNECTION A
AC/DC CONNECTION
CONNECTION B
DC CONNECTION
IO
IO
1
8
+
2
7
+
VO
VF
-
3
6
4
5
1
IF
+
IF
VF
-
-
2
8
7
+
VO
-
3
6
4
5
Figure 1. Terminal Connections
INPUT
OUTPUT
OFF
ON
ON
OFF
Figure 2. True Table
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION  905 E. Walnut St., Garland, TX 75040  (972) 272-3571  Fax (972) 494-2281
E-MAIL: [email protected]
05/06/2013 Rev D
www.micropac.com
Pg. 4 of 7
53259
Power MOSFET Optocoupler
________________________________________________________________________________________
V DD
PULSE GEN
(SEE NOTE 1)
RL
1
8
2
7
VO
MONITOR
NODE
IF
+
VF
IF
MONITOR
C L = 25 pF
3
6
4
5
(SEE NOTE 2)
RM
200
GND
GND
50%
50%
IF
PULSE = 15 ms
WIDTH
90%
10%
VO
t OFF
t ON
NOTES:
1. PULSE GENERATOR HAS THE FOLLOWING CHARACTERISTICS: OUTPUT IMPEDANCE = 50

AND t r = t f = 5.0 ns.
2. LOAD CAPACITANCE (C L) INCLUDES PROBE AND JIG CAPACITANCE.
Figure 3. Switching Test Circuit and Waveform.
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION  905 E. Walnut St., Garland, TX 75040  (972) 272-3571  Fax (972) 494-2281
E-MAIL: [email protected]
05/06/2013 Rev D
www.micropac.com
Pg. 5 of 7
53259
Power MOSFET Optocoupler
___________________________________________________________________________________________
Case Outlines
CASE OUTLINE P
31757 USA
.310 (7.87)
.290 (7.37)
.320 (8.13)
MAX.
ESD
SYMBOL
PIN 1
.050 (1.27)
.035 (0.89)
.390 (9.91)
.370 (9.41)
.110 (2.79)
.090 (2.29)
.170 (4.32)
MAX.
.020 (0.51)
MAX.
CASE OUTLINE X
.050 (1.27)
.035 (0.89)
.390 (9.91)
.370 (9.41)
.110 (2.79)
.090 (2.29)
.020 (.051)
MAX.
.170 (4.32)
MAX.
.320 (8.13)
MAX
.047 (1.19)
TYP
.390 (9.91)
.380 (7.87)
.180 (4.57)
MAX
SEATING
PLANE
NOTES:
1. PIN 1 IS INDICATED BY THE ESD TRIANGLE MARKED ON THE LID OF THE PACKAGE.
2. DIMENSIONS ARE IN INCHES, (mm).
3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY.
4. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS ±.005 (0.13mm).
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION  905 E. Walnut St., Garland, TX 75040  (972) 272-3571  Fax (972) 494-2281
E-MAIL: [email protected]
05/06/2013 Rev D
www.micropac.com
Pg. 6 of 7
53259
Power MOSFET Optocoupler
___________________________________________________________________________________________
Ordering Guide
The following chart explains the ordering procedure for Micropac Part Numbers.
Please contact Micropac for other desired options.
Example: Mii P/N 53259-PA
53259-
Device Type & Model Number
P
A
Case Outline
Lead Finish
Quality Screening Level
P: 8-Pin DIP
A: Solder DIP
X: 8-Pin Gull Wing
C: Gold Plate
None: Per Data Sheet
It is screened IAW Table C-IX of
MIL-PRF-38534, Level H
X: Either A or C
K: Class K, MIL-PRF-38534
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION  905 E. Walnut St., Garland, TX 75040  (972) 272-3571  Fax (972) 494-2281
E-MAIL: [email protected]
05/06/2013 Rev D
www.micropac.com
Pg. 7 of 7