Digital color sensor S9706 12-bit digital output The S9706 is a digital color sensor sensitive to red (λ=615 nm), green (λ=540 nm) and blue (λ=465 nm) regions of the spectrum. Detected signals are serially output as 12-bit digital data. Built-in three 12-bit registers allow simultaneous measurement of RGB three colors. Sensitivity level is adjustable in two steps to cover a wide photometric range. Features Applications 12-bit digital output Display color adjustment Simultaneous measurement of RGB three colors Various applications involving color detection 2-step sensitivity switching (sensitivity ratio of 1 : 9) Low voltage (3.3 V) operation CMOS monolithic photo IC No external components required Feature 01 12-bit digital output Feature 02 Simultaneous measurement of RGB three colors Light signals detected by the photodiode are amplified and convert- The photodiode consists of 9 × 9 elements arrayed in a mosaic ed into 12-bit digital signals. An amplifier is also formed for each of pattern. Each element has an on-chip filter that it sensitive to one the RGB photodiode elements arrayed in the mosaic pattern, allow- color of light, either red (λp=615 nm), green (λp=540 nm) or blue ing simultaneous accurate measurement of the RGB components of (λp=465 nm). incident light. Block diagram Spectral response I/F (Typ. Ta=25 °C) 1.0 Range Vdd Green Register 0.8 Blue I/F Register Serial converter Dout G CK I/F GND B Register Relative sensitivity R Red 0.6 0.4 0.2 Timing circuit Gate 0 300 400 500 600 700 800 Wavelength (nm) KPICC0110EB KPICB0089EA This product does not support lead-free soldering. Solder it by hand. www.hamamatsu.com 1 Digital color sensor Feature S9706 03 2-step sensitivity switching To enable measurement over a wide range of illuminance, the photodiode sensitivity can be selected from two setting modes (high sensitivity mode and low sensitivity mode). The photodiode photosensitive area used to detect light differs depending on which sensitivity mode is selected (high sensitivity mode: 9 × 9 elements, low sensitivity mode: 3 × 3 elements in center). Mode High sensitivity Low sensitivity Effective photosensitive area* 9 × 9 elements 3 × 3 elements * The photosensitive area of S9706 consists of 9 × 9 elements in a mosaic pattern. The effective photosensitive area changes depending on which sensitivity mode is used, “high” or “low”, as explained below. · High sensitivity mode: 9 × 9 elements · Low sensitivity mode: 3 × 3 elements in center 132 110 Pin no. 1 side Pin no. 6 side 110 Range High Low Details of photosensitive area (unit: μm) 132 Sensitivity setting 3 × 3 elements in low sensitivity mode 9 × 9 elements in high sensitivity mode Pin no. 3 side Pin no. 4 side Note: Spaceing between elements is light-shielded. KPICC0124EB Absolute maximum ratings Parameter Symbol Condition Value Supply voltage Vdd Ta=25 °C -0.3 to 6 Load current Io Ta=25 °C ±10 Power dissipation P Ta=25 °C 100 Operating temperature Topr -20 to +85 Storage temperature Tstg -20 to +85 Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure product within the absolute maximum ratings. Unit V mA mW °C °C to use the 2 Digital color sensor S9706 Electrical and optical characteristics (Ta=25 °C, Vdd=5 V, Tg=100 ms, A light source, unless otherwise noted) Parameter Photosensitive area size Effective photosensitive area Spectral response range Peak sensitivity wavelength Supply voltage Current consumption Photosensitivity Incident light power (Conversion value in A light source) Dark output Input high level Input low level High level output voltage Low level output voltage Integration time Hold time Readout clock period Readout pulse width (positive) Readout pulse width (negative) Symbol Condition All elements (9 × 9 elements) Per 1 color, High range Blue λ Green Red Blue λp Green Red Vdd Idd Dark state, no load Sbl Blue, Low range Sgl Green, Low range Srl Red, Low range Sbh Blue, High range Sgh Green, High range Srh Red, High range Ibl Blue, Low range Igl Green, Low range Irl Red, Low range Ibh Blue, High range Igh Green, High range Irh Red, High range Dark Tg=0.5 s Vih Vil Voh Ioh=-0.5 mA Vol Iol=0.5 mA Tg t1 t2 t3 t4 t5 tck tw tck-tw Min. Typ. Max. 1.2 × 1.2 0.32 400 to 540 480 to 600 590 to 720 465 540 615 3.0 5.5 5 10 0.15 0.21 0.27 0.32 0.45 0.59 0.45 0.64 0.83 1.3 1.9 2.5 2.8 4.1 5.4 4.0 5.8 7.6 240 110 78 26 12 8.6 1 Vdd × 0.82 Vdd × 0.18 4.5 0.5 Refer to “Output vs. illuminance” 4 3 3 2000 3 500 200 200 - Unit mm mm2 nm nm V mA LSB/lx klx LSB V V V V μs μs μs μs μs ns ns ns 3 Digital color sensor S9706 Output vs. illuminance High range Low range (Typ. A light source, Green) 10000 Tg=100 s Tg=100 s 1000 10 s 1s Output (LSB) Output (LSB) 1000 (Typ. A light source, Green) 10000 100 ms 100 10 ms 1 ms 100 μs 10 10 s 1s 100 ms 100 10 ms 1 ms 10 100 μs 10 μs 1 0.1 1 10 10 μs 1 0.01 1000 10000 100000 1000000 100 1 0.1 Illuminance (lx) 10 100 1000 10000 100000 Illuminance (lx) KPICB0099EA KPICB0100EA Timing chart Range t5 t3 Gate t4 tg 12 pulses CK 12 pulses ···· ···· t1 t2 Red output (12-bit output) Dout LSB ···· 12 pulses MSB LSB ···· tck tw Green output (12-bit output) ···· MSB Blue output (12-bit output) LSB ···· MSB Operating sequence (1) Set the Gate terminal and CK terminal to “Low”. (2) Select the desired sensitivity with the Range terminal. (3) Set the Gate terminal from “Low” to “High”, to start integrating the light intensity. (4) After the desired integration time (tg) has passed, set the Gate terminal from “High” to “Low” to end the light intensity integration. (5) Measurement data is output from the Dout terminal by inputting 36 CK pulses to the CK terminal. Note 1: A total of 36 CK pulses are required to read out 3-color measurement data. Red data is output by the first 12 pulses, green data by the next 12 pulses, and blue data by the last 12 pulses. Measurement data is output from the LSB side. Note 2: Measurement data changes at the CK pulse rising edge. Note 3: Do not switch the Range terminal during integration time (tg). KPICC0115EB 4 Digital color sensor S9706 Dimensional outline (unit: mm) 4.1 ± 0.2 (Including burr) 1.5 ± 0.4 (2 ×) 5° 4.0* 4.8* 5.0 ± 0.2 (Including burr) 4.7* 1.27 1.27 1.5 ± 0.4 (2 ×) 10° 2.6 0.5 Photosensitive area (1.2 × 1.2) Visual-compensated filter (2.6 × 3.9 × 0.75 t) 7.0 ± 0.3 0.7 ± 0.3 0.7 ± 0.3 (2 ×) 5° ϕ2.0 depth 0.15 max. 0.1 ± 0.1 1.8 0.25 0.8 (2 ×) 10° Dout Vdd GND Range CK Gate Tolerance unless otherwise noted: ±0.1, 2° Chip position accuracy with respect to the package dimensions marked * X, Y≤±0.2 θ≤±3° Lead surface finish: silver plating Packaging: stick (50 pcs/stick) KPICA0060EE Note: If excessive vibration is continuously applied to the glass filter, there is a risk that the filter may come off, so secure the glass filter with a holder. 5 Digital color sensor S9706 Line-up of RGB color sensors 3 × 4 × 1.3t 4 pin (filter 0.75t) S10917-35GT Photodiode 1.0 × 1.0 3 × 1.6 × 1.0t COB (on-chip filter) S10942-01CT Photodiode 1.0 × 1.0 3 × 1.6 × 1.0t COB (on-chip filter) S9706 Digital photo IC 1.2 × 1.2 4 × 4.8 × 1.8t 6 pin (filter 0.75t) S11012-01CR Digital photo IC 1.2 × 1.2 3.43 × 3.8 × 1.6t COB (on-chip filter) * B G R B G 0.56 × 1.22 R IR B I2C 1.68 × 1.18 ×0.58t G compatible S11059-01WT 1.22 × 0.56 WL-CSP color R (on-chip filter) sensor IR * Refer to the spectral response of each product’s datasheet. S11059-02DT /-03DS I2C compatible color sensor 3 × 4.2 ×1.3t 10 pin (on-chip filter) 465 540 615 * 460 530 615 855 460 530 615 855 B G R B G R B G R IR B G R IR 0.18 (A/W) [λ=460 nm] 0.23 (A/W) [λ=540 nm] 0.16 (A/W) [λ=620 nm] 0.18 (A/W) [λ=460 nm] 0.23 (A/W) [λ=540 nm] 0.16 (A/W) [λ=620 nm] 0.2 (A/W) [λ=460 nm] 0.23 (A/W) [λ=540 nm] 0.17 (A/W) [λ=620 nm] 0.21 (A/W) [λ=460 nm] 0.25 (A/W) [λ=540 nm] 0.45 (A/W) [λ=640 nm] B 0.21 (LSB/lx) 1.9 (LSB/lx) G 0.45 (LSB/lx) 4.1 (LSB/lx) R 0.64 (LSB/lx) 5.8 (LSB/lx) B 0.3 (LSB/lx) 2.6 (LSB/lx) G 0.6 (LSB/lx) 5.3 (LSB/lx) R 12.9 (LSB/lx) 1.4 (LSB/lx) B 44.8 (count/lx) 4.4 (count/lx) G 85.0 (count/lx) 8.3 (count/lx) R 117.0 (count/lx) 11.2 (count/lx) IR 30.0 (count/lx) 3.0 (count/lx) B 31.7 (count/lx) 3.35 (count/lx) G 76.2 (count/lx) 7.61 (count/lx) R 94.5 (count/lx) 9.48 (count/lx) IR 15.3 (count/lx) 1.66 (count/lx) High 1.0 × 1.0 B G R B G R B G R B G R Photo High ϕ2.0 4 × 4.8 × 1.8t 6 pin (filter 0.75t) Photosensitivity High Photodiode (mm) High S9702 (mm) Peak sensitivity wavelength (nm) B 460 G 540 R 620 B 460 G 540 R 620 B 460 G 540 R 620 Low Photodiode Package Low S9032-02 Photosensitive area Low Type Low Type no. Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions ∙ Disclaimer ∙ Metal, ceramic, plastic package products ∙ Surface mount type products Information described in this material is current as of August, 2015. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741 China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KPIC1060E13 Aug. 2015 DN 6