Photodiode modules C10439 series Integrates photodiode for precision photometry with low-noise amp The C10439 series photodiode modules are high-precision photodetectors that integrate a photodiode and a current-to-voltage amplifier. The output from these photodiode modules is an analog voltage and can be easily checked with a voltmeter, etc. Since their sensitivity is switchable between two ranges (High/Low), highly accurate output can be obtained by selecting the proper sensitivity range that matches the light level to be detected. Features Applications Voltage output for easy handling Precision photometry Two-range (High/Low) switching function Light source power monitors Only half size of a business card Fluorescence detection of printed matter Can be mounted on optical bench rod (M4) Illuminometers Color difference meters Brix meter Flowmeters, etc. Selection guide Type no. Photodiode type C10439-01 C10439-02 C10439-03 C10439-07 C10439-08 C10439-09 C10439-10 C10439-11 Si InGaAs Peak Photosensitive sensitivity area wavelength (mm) (mm) 2.4 × 2.4 5.8 × 5.8 10 × 10 960 2.4 × 2.4 5.8 × 5.8 10 × 10 φ1 1550 φ3 Dimensions (mm) Conversion impedance Frequency bandwidth -3 dB Zt (V/A) (Hz) H range L range H range L range 1 × 109 1 × 107 10 1k 1 × 106 1 × 104 1k 100 k*1 19 × 46 × 52 19 × 50 × 52 *1: Output amplitude 2 Vp-p Recommended conditions/Absolute maximum ratings Type no. Min. Max. Current consumption Icc Max. Dark state (mA) ±5 ±12 ±2 Supply voltage Vcc (V) C10439-01 C10439-02 C10439-03 C10439-07 C10439-08 C10439-09 C10439-10 C10439-11 Absolute maximum ratings Capacitive load CL Min. Output resistance Zo (pF) 500 Supply voltage Vcc max Operating temperature Topr*2 Storage temperature Tstg*2 (Ω) (V) (°C) (°C) 100 ±13 0 to +50 -10 to +60 *2: No condensation Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. 1 www.hamamatsu.com Photodiode modules C10439 series Electrical and optical characteristics (Ta=25 °C, Vcc=±12 V, unless otherwise noted) Type no. C10439-01 C10439-02 C10439-03 C10439-07 C10439-08 C10439-09 C10439-10 C10439-11 Spectral Peak response sensitivity range wavelength λp λ (nm) (nm) 190 to 1100 500 to 1700 Saturation incident light level*3 Photosensitivity*3 S (nW) H range L range (mV/nW) H range L range 23.6 2360 500 5 23600 2360000 0.5 0.005 Conversion impedance Frequency bandwidth Zt -3 dB (V/A) H range L range (Hz) H range L range 1 × 109 1 × 107 10 1k 1 × 106 1 × 104 1k 100 k*4 960 1550 11800 1180000 1 0.01 *3: λ=λp *4: Output amplitude 2 Vp-p Type no. C10439-01 C10439-02 C10439-03 C10439-07 C10439-08 C10439-09 C10439-10 C10439-11 Maximum output amplitude VFS Output current Io=1 mA (V) Min. Max. +Vcc - 0.5 +Vcc - 0.2 Dark voltage Vd Dark state (mV) Min. Max. -5 +5 Output noise voltage*5 Vn Dark state (mVp-p) Typ. Max. 2 5 Time drift (drift over time)*6 Dark state (mV/day) Min. Max. -0.5 +0.5 *5: Within frequency band *6: Dark voltage variation per day, measured at 25 °C after a 10-minute warm-up after power-on Block diagram Range selector switch Rf +Vcc PD I/V conversion amplifier OUT GND -Vcc KACCC0364EA 2 Photodiode modules C10439 series C10439-01/-02/-03 Output voltage (V) 10 High range 1 0.1 Low range 10-2 10-1 100 101 102 103 (Typ. Ta=25 °C) 700 H range photosensitivity (mV/nW) 100 0.01 10-3 Spectral response (Typ. Ta=25 °C, Vcc=±12 V, λ=λp) 7 600 6 500 5 400 4 300 3 200 2 100 1 L range photosensitivity (mV/nW) Output voltage vs. incident light level 0 0 200 300 400 500 600 700 800 900 1000 1100 104 Wavelength (nm) Incident light level (nW) KACCB0172EA KACCB0345EA C10439-07/-08/-09 Output voltage (V) 10 High range 1 0.1 Low range 101 102 103 104 105 106 (Typ. Ta=25 °C) 0.7 H range photosensitivity (mV/nW) 100 0.01 100 Spectral response (Typ. Ta=25 °C, Vcc=±12 V, λ=λp) 0.007 0.6 0.006 0.5 0.005 0.4 0.004 0.3 0.003 0.2 0.002 0.1 0.001 L range photosensitivity (mV/nW) Output voltage vs. incident light level 0 0.000 200 300 400 500 600 700 800 900 1000 1100 107 Incident light level (nW) Wavelength (nm) KACCB0344EA KACCB0346EA C10439-10/-11 (Typ. Ta=25 °C, Vcc=±12 V, λ=λp) Output voltage (V) 10 High range 1 0.1 Low range 101 102 103 104 105 106 (Typ. Ta=25 °C) 1.2 H range photosensitivity (mV/nW) 100 0.01 100 Spectral response 107 Incident light level (nW) 0.012 1.0 0.010 0.8 0.008 0.6 0.006 0.4 0.004 0.2 0.002 0 400 600 800 1000 1200 1400 1600 L range photosensitivity (mV/nW) Output voltage vs. incident light level 0.000 1800 Wavelength (nm) KACCB0347EA KACCB0348EA 3 Photodiode modules C10439 series Dimensional outlines (unit: mm, tolerance: ±0.2 mm unless otherwise noted) C10439-01/-07 (2 ×) M3 depth 4 Power connector HR10A-7R-4P (73) (Hirose Electric, 4-pin, male) 59 46 52 14.1 14.3 12.6 Output connector BNC 4 26 44 19 High/Low range Front edge of the selector switch case to photosensitive surface 2.35 Photosensitive area 2.4 × 2.4 34 High Low M4 depth 5 KACCA0203EB C10439-02/-08 (2 ×) M3 depth 4 Power connector HR10A-7R-4P (73) (Hirose Electric, 4-pin, male) 59 19 Output connector BNC 14.1 14.3 12.6 52 4 26 44 46 Photosensitive area 5.8 × 5.8 Front edge of the case to photosensitive surface 2.35 34 High/Low range selector switch High Low M4 depth 5 KACCA0204EB 4 Photodiode modules C10439 series C10439-03/-09 (2 ×) M3 depth 4 Power connector HR10A-7R-4P (73) (Hirose Electric, 4-pin, male) 59 19 Output connector BNC 14.1 14.3 12.6 52 4 26 44 46 Photosensitive area 10 × 10 High/Low range Front edge of the selector switch case to photosensitive surface 2.35 34 High Low M4 depth 5 KACCA0205EB C10439-10 (2 ×) M3 depth 4 Power connector HR10A-7R-4P (73) (Hirose Electric, 4-pin, male) 63 19 Output connector BNC 14.1 14.3 12.6 52 4 26 44 50 Photosensitive area 1 Front edge of the case to photosensitive surface 2.6 34 High/Low range selector switch High Low M4 depth 5 KACCA0327EA 5 Photodiode modules C10439 series C10439-11 (2 ×) M3 depth 4 Power connector HR10A-7R-4P (73) (Hirose Electric, 4-pin, male) 63 19 Output connector BNC 14.1 14.3 12.6 52 4 26 44 50 Photosensitive area 3 Front edge of the case to photosensitive surface 3.3 34 High/Low range selector switch High Low M4 depth 5 KACCA0328EA Connection example Power cable (accessory) +V -V GND Photodiode module C10439 series Power supply (±5 to ±12 V) NC BNC cable* Secure with optical bench rod, etc. DC voltmeter, oscilloscope, etc. * BNC cable is not included. KACCC0365EB Accessory · Cable for power supply (no connector on one end) 1m Connector HR10A-7P-4S (Hirose Electric, 4-pin, female) KACCA0194EA 6 Photodiode modules C10439 series Options (sold separately, unit: mm) Optical fiber adapter A12781 series This adapter is used to connect an optical fiber to the photodiode module. Three connector types are available: FC, SC, and SMA. Note: · The optical fiber is not included. · It may not be possible to monitor the total light level depending on the combinations of the photodiode, optical fiber, and fiber adapter that you are using. Select the appropriate components by carefully designing the optical system. A12781-02 (for SC type optical fiber) 2 16 KACCA0329EA A12781-03 (for SMA type optical fiber) 16 14.7 44 52 8 44 16 9.81 2 2 52 A12781-01 (for FC type optical fiber) KACCA0330EA <Assembly procedure> Fix the optical fiber adapter in place using the M3 screw holes in the front of the case. (M3 screws are supplied with the adapter.) 52 44 Screw Screw KACCA0332EA KACCA0331EA 7 Photodiode modules C10439 series Optical fiber (SMA type) A9511 Specifications Photosensitive diameter: φ2 (bundled fiber) Photosensitive numerical aperture: 0.56 SMA connector (1/4-36UNS) Nylon tube 5.1 ± 0.4 This SMA type optical fiber can be used with the photodiode module. The combination of this optical fiber with the SMA type optical fiber adapter (A12781-03) makes it easy to connect an optical fiber to the photodiode module. Note: The SMA type optical fiber adapter (A12781-03) is not included. Tip (aluminum alloy) 17 ± 0.5 20 ± 0.5 5.0 ± 0.4 2.0 1000 ± 20 KACCA0333EA BNC cable E2573 This cable can be used to extract signals from the photodiode module. Specifications Cable specifications: 1.5E-QEV 1000 +50 -0 KACCA0334EA Signal processing unit for photodiode module C10475 This unit converts the output from a photodiode module (C10439 series) into digital signals. High resolution digital output (16 bits) can be retrieved through a serial connection (RS-232C) from a PC. The supplied sample software can be used to easily load measurement data. For the specifications, refer to the C10475 datasheet. Specifications Size: 110 × 100 × 30 mm 8 Photodiode modules C10439 series Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions Notice · Information described in this material is current as of January, 2014. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. Type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(X)" which means preliminary specifications or a suffix "(Z)" which means developmental specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Thorshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1 int. 6, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 China: Hamamatsu Photonics (China) Co., Ltd.: 1201 Tower B, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KACC1139E03 Jan. 2014 DN 9