Signal processing unit for photodiode module C10475 Specifically designed for photodiode modules (C10439 series) The C10475 is a signal processing unit specifically designed to convert the output of a photodiode module (C10439 series) into digital signals. High-resolution digital output (16 bits) can be obtained through serial connection (RS-232C) to a PC. The sample software that comes with the C10475 allows easily obtaining measurement data using the PC. The measurement data can also be recorded in the internal memory (data logger function). The C10475 can also operate on batteries for portability. Features Applications High-resolution digital output (16-bit) Precision photometry Data logger function Light source power monitors Low battery function Fluorescence detection of printed matter Illuminometers Choice of internal battery (+9 V) or AC adapter (+12 V) operation Supplies power to the photodiode module Color difference meters Refractometers Flowmeters, etc. Absolute maximum ratings (Ta=25 °C unless otherwise noted) Parameter Symbol Value Unit Supply voltage Vcc max +14 V Maximum input voltage Vin max ±10 V Topr 0 to +50 °C Operating temperature*1 Storage temperature*1 Tstg -10 to +60 °C *1: No dew condensation When there is a temperature difference between a product and the surrounding area in high humidity environment, dew condensation may occur on the product surface. Dew condensation on the product may cause deterioration in characteristics and reliability. Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. Specifications (Vcc=+12 V, Ta=25 °C, unless otherwise noted) Parameter Supply voltage Input voltage Current consumption*2 Interface A/D readout cycle *2: Dark state Symbol Vcc Vin Icc - Min. +6 -5 RS-232C, 19200 bps, 50 Typ. +12 20 8-bit, Non-parity, 2-stop - www.hamamatsu.com Max. +14 +5 bit - Unit V V mA ms 1 Signal processing unit for photodiode module C10475 Connection example Signal processing unit for photodiode module C10475 AC adapter* (not needed when C10475 operates on battery) Connection cable* for photodiode module RS-232C cable BNC cable* AC 100 to 240 V 50/60 Hz Photodiode module C10439 series PC (with supplied software installed) Secure with optical bench rod, etc. * Accessories KACCC0366EB Sample software (accessory) Data logger setting range Measurement interval: 50 ms to 1 min (50 ms interval) Measurement count: 32000 max. Measurement interval × Meassurement count: 20 hours max. Compatible OS: Microsoft® Windows® 7 SP1 (32-bit, 64-bit) Microsoft Windows 8 (32-bit, 64-bit) Note: Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/ or other countries. 2 Signal processing unit for photodiode module C10475 Dimensional outline (unit: mm) INPUT ON RS-232C Connector for digital output JEY-9P-1A3A90 (JST, 9-pin, male) 12V 1A DC INPUT AUTO ZERO PUSH START DIGITAL OUTPUT 110 ± 1 BNC connector for photodiode module DATA LOG PD SIGNAL PROCCESING UNIT C10475 POWER OFF HEAD Power supply connector for photodiode module HR10A-7R-4S (Hirose Electric, 10-pin, female) 30 ± 1 100 ± 1 KACCA0206EB Accessories (unit: mm) ・Instruction manual ・Sample software CD-ROM ・AC adapter ・BNC cable E2573 +50 1000 - 0 KACCA0334EA ・Cable for photodiode module 1000 ± 50 Connector HR10A-7P-4S (Hirose Electric, 4-pin, female) Connector HR10A-7P-4P (Hirose Electric, 4-pin, male) KACCA0207EB Note: RS-232C cable is not supplied with C10475. For RS-232C cables, use a commercially available cable with 9-pin D-sub connectors (female - female, straight cable). 3 Signal processing unit for photodiode module C10475 Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions ∙ Disclaimer Information described in this material is current as of June, 2016. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741 China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KACC1140E05 Jun. 2016 DN 4