RV-4162 Application Manual Date: January 2014 Headquarters: Micro Crystal AG Mühlestrasse 14 CH-2540 Grenchen Switzerland Tel. Fax Internet Email Revision N°: 2.1 1/39 +41 32 655 82 82 +41 32 655 82 83 www.microcrystal.com [email protected] Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 TABLE OF CONTENTS 1. OVERVIEW ........................................................................................................................................................ 4 1.1. GENERAL DESCRIPTION ......................................................................................................................... 4 1.2. APPLICATIONS ......................................................................................................................................... 4 2. BLOCK DIAGRAM ............................................................................................................................................. 5 2.1. PINOUT ...................................................................................................................................................... 6 2.2. PIN DESCRIPTION .................................................................................................................................... 6 2.3. FUNCTIONAL DESCRIPTION ................................................................................................................... 6 2.4. DEVICE PROTECTION DIAGRAM ........................................................................................................... 7 3. REGISTER ORGANIZATION ............................................................................................................................ 8 3.1. REGISTER ACCESS ................................................................................................................................. 8 3.2. BUFFER / TRANSFER REGISTERS ......................................................................................................... 9 3.3. REGISTER OVERVIEW ........................................................................................................................... 10 3.4. CLOCK SECTION .................................................................................................................................... 11 3.5. CONTROL SECTION ............................................................................................................................... 13 3.6. DATA FLOW OF TIME AND DATE FUNCTION ..................................................................................... 15 3.7. REGISTER RESET VALUE ..................................................................................................................... 15 4. DETAILED FUNCTIONAL DESCRIPTION ..................................................................................................... 16 4.1. CLKOUT FREQUENCY SELECTION ..................................................................................................... 16 4.2. FREQUENCY OFFSET COMPENSATION ............................................................................................. 17 4.2.1. FREQUENCY OFFSET COMPENSATION METHOD ..................................................................... 18 4.2.2. DEFINING FREQUENCY COMPENSATION VALUE ...................................................................... 19 4.3. WATCHDOG TIMER ................................................................................................................................ 20 4.4. ALARM FUNCTION ................................................................................................................................. 21 4.5. CENTURY BITS ....................................................................................................................................... 22 4.6. LEAP YEAR ............................................................................................................................................. 22 4.7. OSCILLATOR STOP DETECTION .......................................................................................................... 23 4.8. OUTPUT DRIVER PIN ............................................................................................................................. 23 2 5. CHARACTERISTICS OF THE I C BUS .......................................................................................................... 24 5.1. BIT TRANSFER ....................................................................................................................................... 24 5.2. START AND STOP CONDITIONS .......................................................................................................... 24 5.3. SYSTEM CONFIGURATION.................................................................................................................... 25 5.4. ACKNOWLEDGE ..................................................................................................................................... 25 2 6. I C BUS PROTOCOL ....................................................................................................................................... 26 6.1. ADDRESSING .......................................................................................................................................... 26 6.2. CLOCK AND CALENDAR READ AND WRITE CYCLES ...................................................................... 26 6.2.1. WRITE MODE ................................................................................................................................... 26 6.2.2. READ MODE AT SPECIFIC ADDRESS ........................................................................................... 27 6.2.3. READ MODE ..................................................................................................................................... 27 2/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 7. ELECTRICAL CHARACTERISTICS ............................................................................................................... 28 7.1. ABSOLUTE MAXIMUM RATINGS .......................................................................................................... 28 7.2. OPERATING AND AC MEASUREMENTS CONDITIONS ...................................................................... 28 7.3. CAPACITANCE ........................................................................................................................................ 28 7.4. FREQUENCY CHARACTERISTICS ........................................................................................................ 29 7.5. FREQUENCY VS. TEMPERATURE CHARACTERISTICS .................................................................... 29 7.6. STATIC CHARACTERISTICS ................................................................................................................. 30 2 7.7. I C INTERFACE TIMING CHARACTERISTICS ...................................................................................... 31 8. APPLICATION INFORMATION ....................................................................................................................... 32 8.1. RECOMMENDED REFLOW TEMPERATURE (LEADFREE SOLDERING) .......................................... 33 9. PACKAGES ..................................................................................................................................................... 34 9.1. DIMENSIONS AND SOLDERPADS LAYOUT ........................................................................................ 34 9.2. MARKING AND PIN #1 INDEX ................................................................................................................ 35 10. PACKING INFORAMTION ............................................................................................................................... 36 10.1. CARRIER TAPE ....................................................................................................................................... 36 10.2. PARTS PER REEL ................................................................................................................................... 37 10.3. REEL 7 INCH FOR 12 mm TAPE ............................................................................................................ 37 10.4. HANDLING PRECAUTIONS FOR CRYSTALS OR MODULES WITH EMBEDDED CRYSTALS ........ 38 11. DOCUMENT REVISION HISTORY .................................................................................................................. 39 3/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 RV-4162 Ultra Small Real Time Clock / Calendar Module with I2C Interface 1. OVERVIEW RTC module with built-in “Tuning Fork” crystal oscillating at 32.768 kHz Serial RTC with alarm functions: 2 - 400 kHz I C serial interface - Memory mapped registers for seconds, minutes, hours, day, date, month, year and century - Tenths / hundredths of seconds register 350 nA timekeeping current at 3.0 V Timekeeping down to 1.0 V 2 1.3 V to 4.4 V I C bus operating voltage Low operating current of 35 A (fSCL = 400 kHz) 32.768 kHz square wave output available at power-up, suitable for driving a uC in low power mode (can be disabled) Programmable 1 Hz to 32.768 kHz square wave output Programmable alarm with interrupt function Oscillator stop detection monitors clock operation Accurate programmable watchdog: 62.5 ms to 31 min timeout Software clock calibration, can adjust timekeeping within +/-2 ppm Automatic leap year compensation Operating temperature range: -40°C to +85°C Ultra small and compact C7 package size, RoHS-compliant and 100% leadfree: 3.2 x 1.5 x 0.8 mm 1.1. GENERAL DESCRIPTION The RV-4162 is a low power serial Real Time Clock (RTC) module with built-in 32.768 kHz crystal (no external components are required for the oscillator). Eight registers are used for the clock / calendar function and are configured in binary coded decimal (BCD) format. An additional 8 registers provide status / control of alarm, calibration, programmable square wave output and watchdog functions. Addresses and data are transferred 2 serially via a two line, bidirectional I C interface. The built-in address register is incremented automatically after each WRITE or READ data byte. Functions available to the user include a time-of-day clock / calendar, alarm interrupts, programmable square wave output, and watchdog. The eight clock address locations contain the century, year, month, date, day, hour, minute, second and tenths / hundredths of a second in 24-hour BCD format. Corrections for 28, 29 (leap year), 30 and 31 day months are made automatically. 1.2. APPLICATIONS The RV-4162 RTC module combines standard RTC functions in high reliable, ultra-small ceramic package: Smallest RTC module (embedded XTAL) in an ultra-small 3.2 x 1.5 x 0.8 mm leadfree ceramic package. Price competitive The unique size and the competitive pricing make this product perfectly suitable for many applications: Automotive: Navigation & Tracking Systems / Dashboard / Tachometers / Car Audio & Entertainment Systems Metering: E-Meter / Heating Counter / Smart Meters / PV Converter Outdoor: ATM & POS systems / Ticketing Systems Medical: Glucose Meter / Health Monitoring Systems Safety: Security & Camera Systems / Door Lock & Access Control Consumer: Gambling Machines / TV & Set Top Boxes / White Goods Automation: Data Logger / Home & Factory Automation / Industrial and Consumer Electronics 4/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 2. BLOCK DIAGRAM 32.768 KHz CRYSTAL OSC CLKOUT 2 DIVIDER 10th/100th Second FREQUENCY-OFFSET COMPENSATION CLKOUT OUTPUT CONTROL OSCILLATOR FAIL DETECTION Seconds 00 Minutes Hours Day Date Month / Century INT SCL SDA INT CONTROL 6 Years Freq. Compensation Watchdog 8 I2C-BUS WATCHDOG INTERFACE ADDRESS REGISTER 1 Month Alarm Date Alarm Hour Alarm Minute Alarm Second Alarm Flags VDD VSS 5 0F POWER UP RESET 3 5/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 2.1. PINOUT C7 Package: #8 #5 #1 SDA #8 SCL #2 CLKOUT #7 N.C. #3 VSS #6 INT #4 N.C. #5 VDD 4162 #1 #4 2.2. PIN DESCRIPTION Symbol Pin # Description SDA CLKOUT VSS N.C. VDD 1 2 3 4 5 Serial Data; open-drain; requires pull-up resistor Clock Output Ground Not Connected Power Supply Voltage INT N.C. SCL 6 Interrupt Output; open-drain; requires pull-up resistor; active low 7 8 Not Connected Serial Clock Input; requires pull-up resistor 2.3. FUNCTIONAL DESCRIPTION The RV-4162 is a low power CMOS Real-Time Clock / Calendar module with built-in “Tuning-Fork” crystal with the nominal frequency of 32.768 kHz; no external components are required for the oscillator circuitry. The oscillator frequency on all devices is tested not to exceed a time deviation of ± 20 ppm (parts per million) at 25°C, which equates to about ± 52 seconds per month. This time accuracy can be further improved to ± 2 ppm at 25°C or better by individually measuring the frequencydeviation in the application and programming a correction value into the frequency compensation register. The CMOS IC contains 16 8-bit RAM registers; the address counter is automatically incremented after each written or read data byte. All sixteen registers are designed as addressable 8-bit parallel registers, although, not all bits are implemented. 6/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 2.4. DEVICE PROTECTION DIAGRAM SDA CLKOUT VSS NC 1 8 2 7 3 6 4 5 SCL NC INT VDD 7/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 3. REGISTER ORGANIZATION The RV-4162 user interface consists of 16 memory mapped registers which include clock, calibration, alarm, watchdog, flags, and square wave control. First 8 registers are the Clock Section at address 00h through 07h. These registers are accessed indirectly via a set of transfer registers. Clock Section (addresses 00h through 07h): These registers are coded in BCD format and contain the century, year, month, day / date, hours, minutes, seconds and tenths / hundredths of seconds in 24-hour format. Corrections for 28, 29 (leap year), 30 or 31 day of months are made automatically. These registers are accessed indirectly through transfer registers. Next 8 registers are the control section at address 08h through 0Fh. Control Section (addresses 08h through 0Fh): These registers are coded in binary format and provide status, frequency compensation, alarm and control of the peripheral functions including the programmable clock output and watchdog functions. The CMOS IC contains 16 8-bit RAM registers. These registers are carried out double: internal counters and external user accessible registers. All sixteen registers are designed as addressable 8-bit parallel registers, although, not all bits are implemented. The address counter is automatically incremented after each written or read data byte. The internal registers keeping track of the time based on the 32.768 kHz clock oscillator and the divider chain. The external registers are independent of the internal counters except that they are updated periodically by the simultaneous transfer of the incremented internal data. To prevent data transition during Interface access, the content of the external register is kept stable whenever the address being read is a clock address (00h to 07h). The update of the external register will resume either when the address-pointer increments to a non-clock address or Interface communication is terminated by sending a “STOP condition”. After “WRITE” to the external register, when the “STOP condition” terminates the Interface communication, the content of the modified external registers is copied into the corresponding internal registers. The divider chain of the 32.768 kHz oscillator will be reset upon the completion of a “WRITE” to any clock address (00h to 07h). 3.1. REGISTER ACCESS During normal operation when the user is not accessing the device, the transfer registers are kept updated with a copy of the Clock Counter data. 2 At the start of an I C read or write cycle, the updating is halted and the present time & date is frozen in the transfer 2 registers. Halting the updates at the start of an I C access is to ensure that all the time & date data transferred out during a read sequence comes from the same instant in time. 2 When writing to the device, each bit is shifted into the RV-4162's I C Interface on the rising edge of the SCL signal. 2 On the 8th clock cycle, each byte is transferred from the I C block into the register addressed by the address pointer. Data written to the Clock Registers (addresses 00h - 07h) is held in the transfer registers until the address pointer 2 increments to 08h, or when STOP condition from I C Interface is received. At which time the data in the transfer registers are simultaneously copied into the Clock Counters and then the clock is restarted. 8/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 3.2. BUFFER / TRANSFER REGISTERS 32.768 kHz OSCILLATOR 1 ad Re Write 2 Clock Section 00h to 07h DIVIDE BY 32768 10th/100th Second COUNTER 1 Hz Seconds COUNTER Minutes Hours COUNTER Day Date Month / Century COUNTER COUNTER Years SCL I2C INTERFACE COUNTER SDA COUNTER Control Section 08h to 0Fh Freq.Compensation 3 Clock Counters Watchdog ... Flags “Clock Counter Registers” containing time & date information are accessed indirectly through transfer registers. 1 At start of Read command, data from “Clock Counter Registers” are copied into “Transfer Register” and 2 the present time & date is frozen. The I C Interface reads the frozen data from Transfer Register, the internal Clock Counter continuous to be updated by the 1 second ticks. 2 When Write to the “Clock Counter Registers”, data are written to the “Transfer Register” and internally transferred to the “Clock Counter Registers” when address pointer increments to 08h or when STOP 2 condition from I C Interface is received. 3 2 Non clock registers of the Control Section 08h to 0Fh are directly accessed from I C Interface. 9/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 3.3. REGISTER OVERVIEW Clock Section (addresses 00h through 07h): These registers are coded in BCD format and contain the century, year, month, day / date, hour, minute, second and tenths/hundredths of a second in 24-hour format. Corrections for 28, 29 (leap year), 30 or 31day months are made automatically. These registers are accessed indirectly through transfer registers. Control Section (addresses 08h through 0Fh): These registers are coded in binary format and provide status, frequency compensation, alarm and control of the peripheral functions incl. the programmable clock-output and watchdog functions. Address Function 00h 10th / 100th Second 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh Seconds Minutes Hours Day Date Month / Century Years Freq. Compensation Watchdog Month Alarm Date Alarm Hour Alarm Minute Alarm Second Alarm Flags Bit 7 8 OS OFIE 0 FD3 0 CB1 80 OUT WD2 AFE ARM4 ARM3 ARM2 ARM1 WDF Bit 6 Bit 5 10th of Second 4 2 40 20 40 20 0 20 FD2 FD1 0 20 CB0 0 40 20 0 Mode WDM4 WDM3 CLKOE 0 ARM5 20 0 20 40 20 40 20 AF 0 Bit 4 1 10 10 10 FD0 10 10 10 16 WDM2 10 10 10 10 10 0 Bit 3 8 8 8 8 0 8 8 8 8 WDM1 8 8 8 8 8 0 Bit 2 Bit 1 Bit 0 100th of Second 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 WDM0 WD1 4 2 4 2 4 2 4 2 4 2 OF 0 1 1 1 1 1 1 1 1 1 WD0 1 1 1 1 1 0 Bit positions labelled with 0 should always be written with logic “0”. 10/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 3.4. CLOCK SECTION th th 10 / 100 Second (address 00h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 8 4 2 1 8 4 2 1 00h 10th / 100th of seconds1) Bit Symbol Value 10th of second 100th of second 0 to 9 0 to 9 7 to 4 3 to 0 Description This register hold the current 10th of second coded in BCD format This register hold the current 100th of second coded in BCD format 1) Generation of 100th and 10th of second is derived from the internal clock source 32.768 kHz divided by 328 = 0.010009766 second. A WRITE to any register of the Clock Section 00h to 07h will reset the divider chain of the 32.768 kHz clock and set the 10th / 100th of second = “00”. Values other than “00” cannot be written to this register. Seconds (address 01h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 01h Seconds OS 40 20 10 8 4 2 1 Bit Symbol Value 7 6 to 0 OS Seconds 0 1 0 to 59 Description 32.768 kHz oscillator is enabled and starts within Tstart 1 sec. 32.768 kHz oscillator is disabled (stopped) This register holds the current seconds coded in BCD format Minutes (address 02h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 02h Minutes OFIE 40 20 10 8 4 2 1 Bit Symbol Value 0 7 6 to 0 OFIE Minutes 1 0 to 59 Description Oscillator fail interrupt is disabled Oscillator fail interrupt is enabled; an interrupt will be issued when an oscillator failure is detected This register holds the current minutes coded in BCD format Hours (address 03h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 20 10 8 4 2 1 03h Hours Bit Symbol Value X Hours 0 0 to 23 7 to 6 5 to 0 Description Unused; must be set to “0” This register holds the current hours coded in BCD format 11/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 Day (address 04h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 04h Day FD3 FD2 FD1 FD0 0 4 2 1 Bit Symbol 7 to 4 FD0 to FD3 3 2 to 0 X Weekday Weekday Sunday Monday Tuesday Wednesday Thursday Friday Saturday 1) Value 0000 to 1111 0 1 to 7 Description Reference FD0 to FD3 bits control CLKOUT frequency 0000 no frequency at CLKOUT See section 4.1 0001 to 1111 select the CLKOUT frequency Unused; must be set to “0” This register holds the current weekday coded in BCD format1) Bit 7 X X X X X X X Bit 6 X X X X X X X Bit 5 X X X X X X X Bit 4 X X X X X X X Bit 3 0 0 0 0 0 0 0 Bit 2 0 0 0 1 1 1 1 Bit 1 0 1 1 0 0 1 1 Bit 0 1 0 1 0 1 0 1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 20 10 8 4 2 1 These bits may be re-assigned by the user. Date (address 05h…bits description) Address Function 05h Date Bit Symbol Value X Date 0 0 to 31 7 to 6 5 to 0 Description Unused; must be set to “0” This register holds the current date coded in BCD format Month / Century (address 06h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 06h Month / Century CB1 CB0 0 10 8 4 2 1 Bit Symbol Value CB1 7 to 6 Century 5 4 to 0 X Month Months January February March April May June July August September October November December 0 0 1 1 0 1 to 12 Bit 7 X X X X X X X X X X X X Description Leap Year CB0 0 Century 20xx (year 2000 – 2099) 2000 = yes 1 Century 21xx (year 2100 – 2199) 2100 = no 0 Century 22xx (year 2200 – 2299) 2200 = no 1 Century 23xx (year 2300 – 2399) 2300 = no Unused; must be set to “0” This register holds the current month coded in BCD format Bit 6 X X X X X X X X X X X X Bit 5 0 0 0 0 0 0 0 0 0 0 0 0 Bit 4 0 0 0 0 0 0 0 0 0 1 1 1 Bit 3 0 0 0 0 0 0 0 1 1 0 0 0 Bit 2 0 0 0 1 1 1 1 0 0 0 0 0 Bit 1 0 1 1 0 0 1 1 0 0 0 0 1 Bit 0 1 0 1 0 1 0 1 0 1 0 1 0 12/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 Years (address 07h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 80 40 20 10 8 4 2 1 07h Years Bit Symbol Value Years 0 to 99 7 to 0 Description This register holds the current year coded in BCD format 3.5. CONTROL SECTION Frequency Compensation (address 08h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 08h Freq. Compensation OUT 0 Mode 16 8 4 2 1 Bit Symbol Value 7 X 5 Mode 4 to 0 0 When OFIE, AFE and Watchdog register are not set to generate an 1 interrupt, the INT pin 6 becomes logic output reflecting the content of this bit 7 “OUT”; See section 4.8 OUT 6 Calibration value Description 0 0 1 0 to 31 Unused; must be set to “0” Negative calibration; See section 4.2 Positive calibration; See section 4.2 This register holds the calibration value coded in binary format Watchdog (address 09h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 09h Watchdog WD2 WDM4 WDM3 WDM2 WDM1 WDM0 WD1 WD0 Bit Symbol 7, 1, 0 WD2 / WD1 / WD0 6 to 2 WDM4 to WDM0 Value 000 100 0 to 31 Description Watchdog Timer Clock Source: 16Hz / 4Hz / 1 Hz / ¼ Hz / 1/60 Hz This register holds the binary coded Watchdog Multiplier value Month Alarm (address 0Ah…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Ah Month Alarm AFE CLKOE 0 10 8 4 2 1 Bit Symbol 7 AFE 6 CLKOE 5 4 to 0 X Month alarm Value 0 1 0 1 0 1 to 12 Description Disables Alarm Flag Enables Alarm Flag Disables CLKOUT (clock output pin 2) Enables CLKOUT (clock output pin 2) Unused; must be set to “0” This register holds the month alarm coded in BCD format Date Alarm (address 0Bh…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Bh Date Alarm ARM4 ARM5 20 10 8 4 2 1 Bit Symbol Value ARM4 – ARM5 Date alarm 00 to 11 7 to 6 5 to 0 1 to 31 Description Alarm repeat mode; See section 4.4 This register holds the date alarm coded in BCD format 13/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 Hour Alarm (address 0Ch…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Ch Hour Alarm ARM3 0 20 10 8 4 2 1 Bit Symbol Value ARM3 X Hour alarm 0/1 0 0 to 23 7 6 5 to 0 Description Alarm repeat mode; See section 4.4 Unused; must be set to “0” This register holds the hour alarm coded in BCD format Minute Alarm (address 0Dh…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Dh Minute Alarm ARM2 40 20 10 8 4 2 1 Bit Symbol Value ARM2 Minute alarm 0/1 0 to 59 7 6 to 0 Description Alarm repeat mode; See section 4.4 This register holds the Minutes Alarm coded in BCD format Second Alarm (address 0Eh…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Eh Second Alarm ARM1 40 20 10 8 4 2 1 Bit Symbol Value ARM1 Second alarm 0/1 0 to 59 7 6 to 0 Description Alarm repeat mode; See section 4.4 This register holds the second alarm coded in BCD format Flags (address 0Fh…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Fh Flags WDF AF 0 0 0 OF 0 0 Bit Symbol Value 7 WDF 6 AF 5 to 3 and 1 to 0 2 1) X OF 0 1 0 1 0 0 1 Description No watchdog timer timeout error detected Watchdog timer timeout error detected, an interrupt will be generated No matching alarm condition detected Alarm flag set when watch matches Alarm settings If AIE = 1, an alarm interrupt will be generated Unused; must be set to “0” No oscillator failure timeout error detected Oscillator failure timeout error detected If OFIE = 1, an oscillator fail interrupt will be generated WDF and AF are read only bits, will be automatically cleared when read. 14/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 3.6. DATA FLOW OF TIME AND DATE FUNCTION 32.768kHz Oscillator Divider Chain 10th / 100th SECOND SECONDS MINUTES HOURS LEAP YEAR CALCULATION DAYS / DATE WEEKDAY MONTHS YEARS CENTURY 3.7. REGISTER RESET VALUE Address 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh Function 10th / 100th Second Seconds Minutes Hours Day Date Month / Century Years Freq. Compensation Watchdog Month Alarm Date Alarm Hour Alarm Minute Alarm Second Alarm Flags Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 X 0 0 X 0 X X X 1 0 0 X X X X X X X X X 0 X X X X 0 1 X X X X X X X X X 0 X X X X 0 X X X X X X X X X X 1 X X X X 0 X X X X X X X X X X X X X X X 0 X X X X X X X X X X X X X X X 0 X X X X X 1 X X X X X X X X X 0 X X X X X X X X X X X X X X X 0 X X X X X X Bit positions labelled as “X” are undefined at power-on and unchanged by subsequent resets. 15/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4. DETAILED FUNCTIONAL DESCRIPTION 4.1. CLKOUT FREQUENCY SELECTION The RV-4162 offers the user a programmable square wave clock which is available at CLKOUT pin 2. CLKOUT frequency is programmable by bits FD3 - FD0 (bit 7 - 4 in register Day 04h) according to below table: CLKOUT frequency selection (address 04h…FD3 - FD0 bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 04h Day FD3 FD2 FD1 FD0 0 4 2 1 Bit Symbol FD3 FD2 FD1 FD0 Frequency Units 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 None 32.768 8.192 4.096 2.048 1.024 512 256 128 64 32 16 8 4 2 1 kHz kHz kHz kHz kHz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz 7 to 4 FD3 to FD0 Values CLKOUT CLKOUT pin 2 is push-pull output and can be disabled either by setting bits FD3 - FD0 = “0000” or by setting bit CLKOE (bit 6 in register Month Alarm 0Ah) = “0”. CLKOUT frequency enable / disable (address 0Ah…CLKOE bit description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Ah Month Alarm AFE CLKOE 0 10 8 4 2 1 Bit Symbol Value CLKOE 0 1 6 Description Disables CLKOUT (clock output pin 2) Enables CLKOUT (clock output pin 2) Default setting at initial power-up is CLKOUT enabled with the frequency of 32.768 kHz. It is recommended to disable CLKOUT when not used by the application to minimize current consumption of the device. 16/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4.2. FREQUENCY OFFSET COMPENSATION The frequency offset compensation function gives the end user the ability to calibrate the clock and to improve the time accuracy of the RV-4162. The RTC is clocked by an oscillator operating a quartz crystal resonator with a nominal frequency of 32.768 kHz. The oscillator frequency on all devices is laser-trimmed and tested not to exceed a time deviation of ±20 ppm at 25°C, which equates to about ±52 seconds per month. The RV-4162 employs periodic clock counter correction. By properly setting the frequency calibration register in the application, it can improve its time accuracy to typically ±2 ppm at 25 °C. The frequency compensation is made by adding or subtracting clock correction counts from the oscillator divider chain at 128 Hz (“divide by 256 stage”), thereby changing the period of a single second. The number of clock pulses which are subtracted (negative calibration) or added (positive calibration) depends upon the value loaded into the five compensation bits (bit 0 to bit 4) of the Frequency Compensation Register. Adding counts speeds the clock up; subtracting counts slows the clock down. The frequency offset compensation is controlled by the Frequency Compensation Register 08h. The calibration value occupies the five LSB’s (bit 4 - 0). These bits can be set to represent any value between 0 and 31 in binary format. Bit 5 “Mode” is a sign bit; “1” indicates positive calibration and speeds up the time, “0” indicates negative calibration and slows down the time Freq. Compensation (address 08h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 08h Calibration Register OUT 0 Mode 16 8 4 2 1 Bit Symbol Value 0 5 Mode 1 4 to 0 Positive Negative Bit 5 1) Calibration value 0 to 31 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 1 1 1 1 1 1 1 0 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 0 1 0 1 0 1 1 0 0 1 1 : 0 0 0 1 1 : 0 0 0 0 0 0 1 0 Description Negative calibration; compensates time deviation when 32.768 kHz clock is too fast Positive calibration; compensates time deviation when 32.768kHz clock is too slow This register holds the calibration value coded in binary format Compensation Value in Decimal +31 +30 : +2 +1 01) -1 -2 : -30 -31 Frequency Compensation Event Time correction Compensation event [ppm] st nd -63.054 1 - 62 minute, 1 event each minute -61.02 1st - 60th minute, 1 event each minute : -4.068 1st - 4th minute, 1 event each minute -2.034 1st & 2nd minute, 1 event each minute 0 No correction +4.068 1st & 2nd minute, 1 event each minute +8.138 1st 4th minute, 1 event each minute : +122.04 1st - 60th minute, 1 event each minute +126.108 1st- 62nd minute, 1 event each minute Default mode at power-up. 17/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4.2.1. FREQUENCY OFFSET COMPENSATION METHOD The frequency compensation itself occurs within a 64 minute cycle. Each binary coded calibration value will trigger two compensation events; compensation events are applied once per minute until the programmed calibration value has been implemented. If, for example a binary “1” is loaded into the Frequency Compensation Register, only the first 2 minutes in the 64 minute cycle will contain one compensation event each. If a binary ‘6’ is loaded, the first 12 minutes will be affected, and so on. Each compensation event either shortens one second by 7.8 ms (256 x 32.768 kHz oscillator clock cycles) or lengthened it by 3.9 ms (128 x 32.768 kHz oscillator clock cycles). Therefore, each calibration value triggers two compensation events resulting in a time adjustment of -2.034 ppm (slower by -0.175 seconds per day) or +4.068 ppm (faster by +0.351 seconds per day) for each of the 31 values of the calibration value. The maximum calibration value (31d) defines the compensation range of -63.054 ppm (slower by -5.449 seconds per day) or +126.108 ppm (faster by +10.899 seconds per day). Oscillator 32.768 kHz Clock 32.768 kHz Clock Frequency Divider Chain 256 Hz Clock 128 Hz Clock 1 2 +7.8 ms +2.034 ppm 2 Positive Compensation Event 128 Hz +1 Clock 1 4 3 2 3 4 -3.9 ms -1.017 ppm Negative Compensation Event 128 Hz -1 Clock 1 2 1 1 2 3 4 Negative compensation (when 32.768 kHz clock too fast): Then for each compensation event, a clock pulse at the 128 Hz divider stage is suppressed to compensate the frequency deviation of the 32.768 kHz clock. Positive compensation (when 32.768 kHz clock too slow): Then for each compensation event a clock pulse at the 128 Hz divider stage is added to compensate the frequency deviation of the 32.768 kHz clock. Note that frequency compensation events do not affect the frequency at CLKOUT pin 2. 18/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4.2.2. DEFINING FREQUENCY COMPENSATION VALUE The simplest method for ascertaining the frequency deviation a given RV-4162 is to measure the frequency deviation at CLKOUT pin 2. The measured frequency deviation, then, is transformed into an individual compensation value for this device and programmed into the Frequency Compensation Register (08h). For test purpose, the following configuration will establish a 32.768 kHz clock at CLKOUT pin 2: Bit OS = “0” (bit 7 in register Seconds 01h): enables 32.768 kHz oscillator Bits FD3 – FD0 = “0001” (bits 7 - 4 in register Day 04h): select 32.768 kHz CLKOUT frequency Bit CLKOE = “1” (bit 6 in register Month Alarm 0Ah): enables CLKOUT pin 2 Please note that this is the default setting at power-up. The frequency deviation on 32.768000 kHz CLKOUT indicates the degree and direction of time deviation for this device. A frequency deviation of +0.032768 Hz equals to +1 ppm. For example, a reading of 32.768650 kHz indicates a frequency deviation of +20 ppm (faster by +1.73 seconds per day), requiring negative compensation value of “-10d” (xx001010) to be loaded into the Frequency Compensation Register (08h) for frequency compensation. It’s important to define the frequency compensation value at an ambient temperature (around 25°C) because of the crystal’s frequency vs. temperature characteristics shown on page 29. 19/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4.3. WATCHDOG TIMER The Watchdog Timer can be used to detect an out-of-control microprocessor or deadlock of the Interface communication. The function of the Interface Watchdog Timer is based on internal Timer / Counter which is periodically reset by the internal control logic. If the control logic does not reset the Watchdog Timer within the programmed time-out period, the RV-4162 detects an Interface time-out and sets Watchdog Flag (WDF = 1, bit 7, in register Flags 0Fh) and generates an interrupt on INT pin 6. The user programs the Watchdog Timer by setting the desired amount of time-out into the Watchdog register at address 09h, a value of 00h will disable the watchdog function until it is again programmed to a new value. The amount of time-out is then determined by selecting a Watchdog Timer Source Clock WD2 - WD0 and the multiplication with the Watchdog Multiplier value WDM4 - WDM0. Bits WDM4 - WDM0 store a binary coded Watchdog Multiplier value. Bits WD2 - WD0 select the Watchdog Timer Clock Source. For example: writing 00001110 in the Watchdog register = 3 x 1 second or 3 seconds. Watchdog (address 09h…bits description) Address Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 09h Watchdog WD2 WDM4 WDM3 WDM2 WDM1 WDM0 WD1 WD0 Bit Symbol Value 7 to 0 Watchdog A value of 00h disables Watchdog Timer function 7, 1, 0 WD2 / WD1 / WD0 6 to 2 WDM4 to WDM0 00h 000 100 0 to 31 Description Setting “00000” with any combination of WD2 - WD0, other than “000”, will result in an immediate watchdog time-out WDM4 WDM3 WDM2 WDM1 WDM0 Value 0 0 0 0 0 00h 0 0 0 1 1 1 1 1 0 … 1 1 1 1 0 1 01d … 30d 31d WD2 0 0 0 0 1 1 1 1 WD1 0 0 1 1 0 0 1 1 WD0 0 1 0 1 0 1 0 1 Description Watchdog Timer Clock Source: 16Hz / 4Hz / 1 Hz / ¼ Hz / 1/60 Hz This register holds the binary coded Watchdog Multiplier value Defines binary coded Watchdog Multiplier value Value 000 001 010 011 100 101 110 111 Timer Clock Source Time 16 Hz 62.5ms 4 Hz 250 ms 1 Hz 1 second ¼ Hz 4 seconds 1 /60 Hz 1 minute Invalid combination, will not enable Watchdog Timer Invalid combination, will not enable Watchdog Timer Invalid combination, will not enable Watchdog Timer 2 The Watchdog time-out period starts when the I C interface communication is initiated. If the control logic does not reset the Watchdog Timer within the programmed time-out period, the RV-4162 detects an Interface time-out and sets the Watchdog Flag (WDF = 1, bit 7, in register Flags 0Fh) and generates an interrupt on INT pin 6. The Watchdog Timer can only be reset by having the microprocessor perform a WRITE to the Watchdog Register 09h. The time-out period then starts over. Should the Watchdog Timer time-out, any value may be written to the watchdog register in order to clear the INT pin 6. A value of 00h will disable the watchdog function until it is again programmed to a new value. A READ of the flags register will reset the Watchdog Flag (bit 7; register 0Fh). The watchdog function is automatically disabled upon power-up, and the Watchdog Register is cleared. Note: A WRITE to any clock register will restart the Watchdog Timer. 20/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4.4. ALARM FUNCTION Addresses locations 0Ah-0Eh contain the alarm settings. The alarm can be configured to go off at a prescribed time on a specific month, date, hour, minute, or second, or repeat every year, month, day, hour, minute, or second. Bits ARM5 - ARM1 put the alarm in the repeat mode of operation. The table below shows the possible configurations. Codes not listed in the table default to the once per second mode to quickly alert the user of an incorrect alarm setting. When the clock information matches the alarm clock settings based on the match criteria defined by ARM5 ARM1, the AF (alarm flag) is set. If AFE (alarm flag enable) is also set, the alarm condition activates the INT pin 6. To disable the alarm, write “0” to the Date Alarm register and to ARM5 - ARM1. Note: If the address pointer is allowed to increment to the flag register address, an alarm condition will not cause the interrupt / flag to occur until the address pointer is moved to a different address. It should also be noted that if the last address written is the Second Alarm, the address pointer will increment to the flag address, causing this situation to occur. The INT is cleared by a READ to the Flags register as shown in figure below. A subsequent READ of the Flags register is necessary to see that the value of the alarm flag has been reset to “0”. Alarm interrupt reset waveform: INT Alarm Repeat Mode Settings (addresses 0Bh to 0Eh, ARM5 to ARM1…bits description) Address 0Bh 0Ch 0Dh 0Eh Function Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Date Alarm Hour Alarm Minute Alarm Second Alarm ARM4 ARM3 ARM2 ARM1 ARM5 0 40 40 20 20 20 20 10 10 10 10 8 8 8 8 4 4 4 4 2 2 2 2 1 1 1 1 ARM5 ARM4 ARM3 ARM2 ARM1 1 1 1 1 1 0 1 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 0 1 0 0 0 0 0 Alarm setting Once per second Once per minute Once per hour Once per day Once per month Once per year 21/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4.5. CENTURY BITS The two century bits, CB1 and CB0, are bits 7 and 6, respectively, in the Month / Century register at address 06h. Together, they comprise a 2-bit counter which increments at the turn of each century. CB1 is the most significant bit. The user may arbitrarily assign the meaning of CB1:CB0 to represent any century value, but the simplest way of using these bits is to extend the Years register (07h) by mapping them directly to bits 9 and 8 (the reader is reminded that the year register is in BCD format). Higher order year bits can be maintained in the application software. Century bits CB1 and CB0: 4.6. LEAP YEAR Leap year occurs every four years, in years which are multiples of 4. For example, 2012 was a leap year. An exception to that is any year which is a multiple of 100. For example, the year 2100 is not a leap year. A further exception is that years which are multiples of 400 are indeed leap years. Hence, while 2100 is not a leap year, 2400 is. During any year which is a multiple of 4, the RV-4162 RTC will automatically insert leap day, February 29. Therefore, the application software must correct for this during the exception years (2100, 2200, etc.) as noted above. 22/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 4.7. OSCILLATOR STOP DETECTION If the oscillator fail (OF) bit is internally set to a “1”, this indicates that the oscillator has either stopped, or was stopped for some period of time and can be used to judge the validity of the clock and date data. This bit will be set to “1” any time the oscillator stops. In the event the OF bit is found to be set to “1” at any time other than the initial power-up, the STOP bit (OS) should be written to a “1”, then immediately reset to “0”. This will restart the oscillator. The following conditions can cause the OF bit to be set: The first time power is applied (defaults to a “1” on power-up) Note: if the OF bit cannot be written to “0” four (4) seconds after the initial power-up, the STOP bit (OS) should be written to a “1”, then immediately reset to “0”. The voltage present on VDD or battery is insufficient to support oscillation The OS bit is set to “1” If the oscillator fail interrupt enable bit (OFIE) is set to a “1”, the INT pin 6 will also be activated. The INT output is cleared by resetting the OFIE or OF bit to “0” (NOT by reading the Flag register). The OF bit will remain set to “1” until written to logic “0”. The oscillator must start and have run for at least 4 seconds before attempting to reset the OF bit to “0”. If the trigger event occurs during a power-down condition, this bit will be set correctly. 4.8. OUTPUT DRIVER PIN When the OFIE bit, AFE bit, and Watchdog register are not set to generate an interrupt, the INT pin 6 becomes an output driver that reflects the contents of bit 7 (OUT bit) of the Freq. Compensation register. In other words, when bit 7 (OUT bit) is a “0”, then the INT pin 6 will be driven low. Note: The INT pin 6 is an open-drain which requires an external pull-up resistor. 23/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 5. CHARACTERISTICS OF THE I2C BUS 2 The I C bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a Serial DAta line (SDA) and a Serial CLock line (SCL). Both lines are connected to a positive supply via pull-up resistors. Data transfer is initiated only when the bus is not busy. 5.1. BIT TRANSFER One data bit is transferred during each clock pulse. The data on the SDA line remains stable during the HIGH period of the clock pulse, as changes in the data line at this time are interpreted as a control signals. Data changes should be executed during the LOW period of the clock pulse (see figure below). Bit transfer: 5.2. START AND STOP CONDITIONS Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line, while the clock is HIGH, is defined as the START condition (S). A LOW-to-HIGH transition of the data line, while the clock is HIGH, is defined as the STOP condition (P) (see figure below). Definition of START and STOP conditions: For this device, a repeated START is not allowed. Therefore, a STOP has to be released before the next START. 24/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 5.3. SYSTEM CONFIGURATION 2 2 Since multiple devices can be connected with the I C bus, all I C bus devices have a fixed and unique device number built-in to allow individual addressing of each device. 2 The device that controls the I C bus is the Master; the devices which are controlled by the Master are the Slaves. A device generating a message is a Transmitter; a device receiving a message is the Receiver. The RV-4162 acts as a Slave-Receiver or Slave-Transmitter. 2 Before any data is transmitted on the I C bus, the device which should respond is addressed first. The addressing is always carried out with the first byte transmitted after the start procedure. The clock signal SCL is only an input signal, but the data signal SDA is a bidirectional line. System configuration: 5.4. ACKNOWLEDGE The number of data bytes transferred between the START and STOP conditions from transmitter to receiver is unlimited. Each byte of 8 bits is followed by an acknowledge cycle. • • • • A slave receiver, which is addressed, must generate an acknowledge cycle after the reception of each byte Also a master receiver must generate an acknowledge cycle after the reception of each byte that has been clocked out of the slave transmitter The device that acknowledges must pull-down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the related acknowledge clock pulse (set-up and hold times must be considered) A master receiver must signal an end of data to the transmitter by not generating an acknowledge cycle on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition 2 Acknowledgement on the I C bus is shown on the figure below. 2 Acknowledgement on the I C bus: 25/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 6. I2C BUS PROTOCOL 6.1. ADDRESSING 2 2 One I C bus slave address (1101000) is reserved for the RV-4162. The entire I C bus slave address byte is shown in the table below: 2 I C salve address byte: Slave address 6 7 Bit 5 4 3 2 1 0 MSB LSB 1 1 0 1 0 0 0 R/ W 2 After a START condition, the I C slave address has to be sent to the RV-4162 device. The R/ W bit defines the direction of the following single or multiple byte data transfer. In the write mode, a data transfer is terminated by sending either the STOP condition or the START condition of the next data transfer. 6.2. CLOCK AND CALENDAR READ AND WRITE CYCLES 6.2.1. WRITE MODE Master transmits to Slave-Receiver at specified address. The Word Address is 8-bit value that defines which register is to be accessed next. The upper four bits of the Word Address are not used. After reading or writing one byte, the Word Address is automatically incremented by 1. Master sends out the “Start Condition”. Master sends out the “Slave Address”, D0h for the RV-4162; the R/ W bit in write mode. Acknowledgement from the RV-4162. Master sends out the “Word Address” to the RV-4162. Acknowledgement from the RV-4162. Master sends out the “data” to write to the specified address in step 4). Acknowledgement from the RV-4162. Steps 6) and 7) can be repeated if necessary. The address will be incremented automatically in the RV-4162. Master sends out the “Stop Condition”. 1 2 S SLAVE ADDRESS 3 0 A R/W 1) 2) 3) 4) 5) 6) 7) 8) 9) 4 5 6 7 8 WORD ADDRESS A DATA A DATA 9 A P Acknowledge from RV-4162 26/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 6.2.2. READ MODE AT SPECIFIC ADDRESS Master reads data after setting Word Address: Master sends out the “Start Condition”. Master sends out the “Slave Address”, D0h for the RV-4162; the R/ W bit in write mode. Acknowledgement from the RV-4162. Master sends out the “Word Address” to the RV-4162. Acknowledgement from the RV-4162. Master sends out the “Re-Start Condition” (“Stop Condition” followed by “Start Condition”) Master sends out the “Slave Address”, D1h for the RV-4162; the R/ W bit in read mode. Acknowledgement from the RV-4162. At this point, the Master becomes a Receiver, the Slave becomes the Transmitter. 9) The Slave sends out the “data” from the Word Address specified in step 4). 10) Acknowledgement from the Master. 11) Steps 9) and 10) can be repeated if necessary. The address will be incremented automatically in the RV-4162. 12) The Master, addressed as Receiver, can stop data transmission by not generating an acknowledge on the last byte that has been sent from the Slave-Transmitter. In this event, the Slave-Transmitter must leave the data line HIGH to enable the Master to generate a stop condition. 13) Master sends out the “Stop Condition”. 1) 2) 3) 4) 5) 6) 7) 8) 1 3 0 A SLAVE ADDRESS 4 5 WORD ADDRESS A 6 P 7 S SLAVE ADDRESS 8 1 A 9 10 11 DATA A DATA 12 13 A P R/W R/W S 2 Acknowledge from Master Acknowledge from RV-4162 No acknowledge 6.2.3. READ MODE Master reads Slave-Transmitter immediately after first byte: 1) Master sends out the “Start Condition”. 2) Master sends out the “Slave Address”, D1h for the RV-4162; the R/ W bit in read mode. 3) Acknowledgement from the RV-4162. At this point, the Master becomes a Receiver, the Slave becomes the Transmitter 4) The RV-4162 sends out the “data” from the last accessed Word Address incremented by 1. 5) Acknowledgement from the Master. 6) Steps 4) and 5) can be repeated if necessary. The address will be incremented automatically in the RV-4162. 7) The Master, addressed as Receiver, can stop data transmission by not generating an acknowledge on the last byte that has been sent from the Slave-Transmitter. In this event, the Slave-Transmitter must leave the data line HIGH to enable the Master to generate a stop condition. 8) Master sends out the “Stop Condition”. 2 3 S SLAVE ADDRESS 1 A 4 5 DATA A 6 DATA 7 8 A P R/W 1 Acknowledge from RV-4162 Acknowledge from Master No acknowledge 27/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 7. ELECTRICAL CHARACTERISTICS 7.1. ABSOLUTE MAXIMUM RATINGS In accordance with the Absolute Maximum Rating System IEC 60134 PARAMETER 1) 2) SYMBOL Supply voltage Input voltage VDD VI Output voltage Output current Power dissipation Operating ambient temperature range Storage temperature range VO IO PD TOPR TSTO Electro Static Discharge voltage VESD CONDITIONS >GND / <VDD Stored as bare product HBM1) TA = 25°C MM2) TA = 25°C MIN. MAX. UNIT GND -0.3 GND -0.2 +5.0 VDD +0.3 V V GND -0.2 VDD +0.3 20 1 +85 +125 >1500 >1000 V mA W °C °C V V -40 -55 HBM: Human Body Model, according to JESD22-A114. MM: Machine Model, according to JESD22-A115. These data are based on characterization results, not tested in production. Stresses above these listed maximum ratings may cause permanent damage to the device. Exposure beyond specified operating conditions may affect device reliability or cause malfunction. 7.2. OPERATING AND AC MEASUREMENTS CONDITIONS PARAMETER1) RV-4162 Supply voltage (VDD) Operating ambient temperature (TA) Load capacitance (CL) Input rise and fall times Input pulse voltages Input and output timing ref. voltages 1) UNIT 1.3 to 4.4 -40 to +85 50 5 0.2 VDD to 0.8 VDD 0.3 VDD to 0.7 VDD V °C pF ns V V Output Hi-Z is defined as the point where data is no longer driven. 7.3. CAPACITANCE PARAMETER1) 2) Input capacitance Output capacitance Low-pass filter input time constant (SDA and SCL) 1) 2) 3) SYMBOL CIN COUT3) tLP MIN. MAX. - 7 10 50 UNIT pF pF ns Effective capacitance measured with power supply at 3.6 V; sampled only, not 100% tested. At 25°C, f = 1 MHz. Outputs deselected. 28/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 7.4. FREQUENCY CHARACTERISTICS Tamb= +25°C; fOSC= 32.768 kHz PARAMETER SYMBOL CONDITIONS Frequency accuracy Frequency vs. temperature characteristics Turnover temperature Aging first year max. Oscillator start-up voltage Oscillator start-up time Δf/f Tamb = +25°C Δf/TOPR MIN. ppm TOPR = -40°C to +85°C TO Δf/f VStart TStart TYP. -0.035 /°C2 ppm (TOPR-T0) (+/-10%) +25 CLKOUT duty cycle UNIT +/-20 2 20 - 30 +/-3 Tamb = +25°C 10 seconds VDD = 3.0V FCLKOUT = 32.7678 kHz TAMB = +25°C MAX. 1 °C ppm V s 40/60 % 1.5 50 ppm 7.5. FREQUENCY VS. TEMPERATURE CHARACTERISTICS 20.0 T0 = 25°C (±5°C) 0.0 -20.0 ΔF/F [ppm] -40.0 -60.0 -0.035 * (T-T0)2 ppm (±10%) -80.0 -100.0 -120.0 -140.0 -160.0 -180.0 -60 -40 -20 0 20 40 60 80 100 T [°C] 29/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 7.6. STATIC CHARACTERISTICS Valid for Tamb= -40°C to +85°C; VDD= 1.3 V to 4.4 V (except where noted) PARAMETER Supply voltage SYMBOL CONDITIONS VDD1) Clock I2C bus (400 kHz) MIN. TYP. 1.0 1.3 VDD = 4.4 V SCL = 400 kHz (no load) 50 35 30 20 VDD = 3.6 V Supply current IDD1 VDD = 3.0 V VDD = 2.5 V VDD = 2.0 V VDD = 4.4 V Supply current (standby) SCL = 0 Hz CLKOUT off All inputs VDD - 0.2 V / VSS + 0.2 V 375 350 310 270 VDD = 3.6 V IDD2 VDD = 3.0 V at 25°C VDD = 2.0 V at 25°C VDD = 1.0 V at 25°C LOW level input voltage HIGH level input voltage VIL VIH HIGH level output voltage VOH LOW level output voltage VOL -0.2 0.7 VDD VDD = 4.4 V IOH = -1.0 mA (push-pull) VDD = 4.4 V; IOL = 3.0 mA (SDA) VDD = 4.4 V; IOL = 1.0 mA (SQW, INT ) Pull-up supply voltage (open drain) Input leakage current Output leakage current 1) ILI ILO MAX. UNIT 4.4 4.4 100 70 V V µA µA µA µA µA nA nA nA nA nA V V 950 700 500 450 400 0.3 VDD VDD +0.3 2.4 V 0.4 V 0.4 INT 4.4 V 0 V VIN VDD 0 V VOUT VDD ±1 ±1 µA µA Oscillator start-up guaranteed at 1.5 V only. 30/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 7.7. I2C INTERFACE TIMING CHARACTERISTICS Valid for Tamb = -40°C to +85°C; VDD= 1.3 V to 4.4 V (except where noted) 1) PARAMETER SYMBOL SCL Clock Frequency Start Condition Set-up Time (only relevant for a repeated start condition) Start Condition Hold Time (after this period the first clock pulse is generated) Data Set-up Time1) Data Hold Time Stop Condition Set-up Time Bus Free Time between STOP and START condition SCL “LOW time” SCL “HIGH time” SCL and SDA Rise Time SCL and SDA Fall Time Watchdog Output Pulse Width fSCL MIN MAX UNIT 0 400 kHz tSU ; STA 600 ns tHD ; STA 600 ns tSU ; DAT tHD ; DAT tSU ; STO tBUF tLOW tHIGH tr tf trec 100 0 600 1.3 1.3 600 ns µs ns µs µs ns ns ns ms 96 300 300 98 Transmitter must internally provide a hold time to bridge the undefined region (300 ns max) of the falling edge of SCL. 31/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 8. APPLICATION INFORMATION Operating RV-4162: VDD 1 2 10 nF VDD SDA SDA SCL SCL μ Controller RV-4162 INT INT CLKOUT VSS 1 2 3 3 VSS A 10 nF decoupling capacitor is recommended close to the device. Interface lines SCL, SDA and INT are open drain and require pull-up resistor to VDD. CLKOUT offers selectable frequencies 1 Hz to 32.768 kHz for application use. If not used, it is recommended to disable CLKOUT for optimized current consumption. Operating RV-4162 with SuperCap backup supply voltage: VDD 5 6 VDD 4 1F SDA SDA SCL SCL RV-4162 INT CLKOUT VSS 4 5 6 μ Controller INT VSS A SuperCap combined with a low Vf diode can be used to operate the RV-4162 in stand-by or backup supply voltage mode. If a SuperCap is used, it is recommended using a Schottky diode due to its low forward voltage Vf. If application requires, the INT pull-up resistor can be tied to the backup supply voltage, in order to generate an interrupt even when main supply voltage VDD is off. 32/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 8.1. RECOMMENDED REFLOW TEMPERATURE (LEADFREE SOLDERING) Maximum Reflow Conditions in accordance with IPC/JEDEC J-STD-020C “Pb-free” Temperature Profile Average ramp-up rate Ramp down Rate Time 25°C to Peak Temperature Preheat Temperature min Temperature max Time Tsmin to Tsmax Soldering above liquidus Temperature liquidus Time above liquidus Peak temperature Peak Temperature Time within 5°C of peak temperature Symbol (Tsmax to Tp) Tcool Tto-peak Condition 3°C / second max 6°C / second max 8 minutes max Unit °C / s °C / s m Tsmin Tsmax ts 150 200 60 - 180 °C °C Sec TL tL 217 60 – 150 °C sec Tp tp 260 20 - 40 °C sec 33/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 9. PACKAGES 9.1. DIMENSIONS AND SOLDERPADS LAYOUT C7 Package: Package dimensions (bottom view): Recommended solderpad layout: All dimensions in mm typical. 34/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 9.2. MARKING AND PIN #1 INDEX C7 Package: 35/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 10.PACKING INFORAMTION 10.1. CARRIER TAPE 12 mm Carrier-Tape: Material: Polystyrene / Butadine or Polystyrol black, conductive Cover Tape: Base Material: Adhesive Material: Peel Method: Polyester, conductive 0.061 mm Pressure-sensitive Synthetic Polymer Middle part removed, sticky sides remain on carrier C7 Package: User Direction of Feed Tape Leader and Trailer: 300 mm minimum. All dimensions in mm. 36/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 10.2. PARTS PER REEL C7 Package: Reels: Diameter 7” 7” Material Plastic, Polystyrol Plastic, Polystyrol RTC’s per reel 1’000 5’000 10.3.REEL 7 INCH FOR 12 mm TAPE Reel: Diameter 7” Material Plastic, Polystyrol 37/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 10.4. HANDLING PRECAUTIONS FOR CRYSTALS OR MODULES WITH EMBEDDED CRYSTALS The built-in tuning-fork crystal consists of pure Silicon Dioxide in crystalline form. The cavity inside the package is evacuated and hermetically sealed in order for the crystal blank to function undisturbed from air molecules, humidity and other influences. Shock and vibration: Keep the crystal / module from being exposed to excessive mechanical shock and vibration. Micro Crystal guarantees that the crystal / module will bear a mechanical shock of 5000g / 0.3 ms. The following special situations may generate either shock or vibration: Multiple PCB panels - Usually at the end of the pick & place process the single PCBs are cut out with a router. These machines sometimes generate vibrations on the PCB that have a fundamental or harmonic frequency close to 32.768 kHz. This might cause breakage of crystal blanks due to resonance. Router speed should be adjusted to avoid resonant vibration. Ultrasonic cleaning - Avoid cleaning processes using ultrasonic energy. These processes can damages crystals due to mechanical resonance of the crystal blank. Overheating, rework high temperature exposure: Avoid overheating the package. The package is sealed with a seal ring consisting of 80% Gold and 20% Tin. The eutectic melting temperature of this alloy is at 280°C. Heating the seal ring up to >280°C will cause melting of the metal seal which then, due to the vacuum, is sucked into the cavity forming an air duct. This happens when using hot-air-gun set at temperatures >300°C. Use the following methods for rework: Use a hot-air- gun set at 270°C. Use 2 temperature controlled soldering irons, set at 270°C, with special-tips to contact all solder-joints from both sides of the package at the same time, remove part with tweezers when pad solder is liquid. 38/39 Micro Crystal Ultra Small Real Time Clock / Calendar Module RV-4162 11.DOCUMENT REVISION HISTORY Date Revision # Revision Details April 2010 1.2 First release December 2013 2.0 New version January 2014 2.1 Static characteristics corrections Information furnished is believed to be accurate and reliable. However, Micro Crystal assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use . In accordance with our policy of continuous development and improvement, Micro Crystal reserves the right to modify specifications mentioned in this publication without prior notice. This product is not authorized for use as critical component in life support devices or systems. 39/39