Semiconductor Product Catalog IXYS Integrated Circuits Division IXYS Integrated Circuits Division is a wholly owned subsidiary of IXYS Corporation. Conveniently located close to Boston, Massachusetts, USA, IXYS Integrated Circuits Division designs, manufactures, and markets a wide variety of semiconductor devices, and is a major provider of optically isolated electronic products. Clare, Inc., founded by Carl P. Clare in 1937 as C. P. Clare & Company, designed and manufactured electromechanical relays (EMR) for the rapidly growing power and telephony markets of the time. C. P. Clare & Company products found their way into aviation and communications products from the very beginning of World War II to the end. Continuously operating under various names from 1937 until the present, C. P. Clare & Company, as Clare, Inc., was purchased by IXYS Corporation in 2002, and is now known as IXYS Integrated Circuits Division (as of April, 2012). IXYS Integrated Circuits Division’s unique mix of high voltage wafer fab, isolation barrier expertise, multi-chip packaging experience, and expertise in analog, power, and mixed signal design, points the way to more functionality in a smaller footprint at lower cost for your designs. • High Voltage IGBT and MOSFET Drivers: High speed, high voltage IGBT and MOSFET drivers, some of which are AEC Q100 qualified. • Non-Volatile Digital Programmable Capacitors: For fine-tuning of capacitance-sensitive circuits. • High Voltage ICs: High voltage 8-channel and 16-channel Analog Switches for the medical and imaging markets, high voltage LED Drivers, and others. • Solid State Relays (SSR): One of the industry’s broadest lines of optically isolated SSRs, available in a wide selection of configurations, blocking voltages, and load currents. • Power Market: Power Solid State Relays; SCR-based AC Power Switches (Zero-Cross & Rapid Turn-On); and N-Channel, Depletion-Mode, Field Effect Transistors (FET). • Illumination: High voltage, grid-powered, high-brightness LED Drivers. • High Speed Digital Optical Isolators: New high speed isolators that pass DC signals, require no refresh clocking, and provide 3750Vrms of galvanic isolation. • I2C Optically Isolated Bus Repeaters: New high speed repeaters that buffer both I2C signals, require no refresh clocking, and provide 3750Vrms of galvanic isolation. • Portable reader devices: Display drivers for today’s popular electronic-paper readers. • Telecom: A broad range of products that includes Line Card Access Switch (LCAS) products, LITELINK® Silicon Data Access Arrangement (DAA), phone-line interface and monitoring devices, DC Termination devices for xDSL and ISDN applications, Cybergate™ DAA, and others. Hi-Reliability Program Building on over 20 years of experience supplying Hi-Rel parts to the aerospace industry, IXYS Integrated Circuits Division now offers a line of high-reliability Solid State Relays and Optocouplers that feature full product traceability, extremely low PPM failure rates, guaranteed operation from -40ºC to +85ºC (and up to 105ºC upon request), 100% burn-in (HTRB) 48 hours minimum, 100% post burn-in electrical tests at room temperature and at 85ºC, and thermal cycle (by sample or 100% for 20 cycles). Any IXYS Integrated Circuits Division Solid State Relay (SSR) or Optocoupler offered in this catalog can be provided as a Hi-Rel device based on extensive additional environmental stressing and screening performed on standard commercial parts. Please go to www.ixysic.com/Products/HiRelProgram.htm for full details. Custom High Voltage Semiconductor Design Services IXYS Integrated Circuits Division offers design services to the industry for the custom development of high voltage semiconductor devices. The company’s wafer fabrication facility features a 600V BCDMOS process on a bonded-wafer, silicon-on-insulator, trench-isolated technology for IC development. Monolithic silicon with high voltage vertical DMOSFETs, along with CMOS logic and bipolar transistors from IXYS Integrated Circuits Division, address many applications requiring a high voltage interface. In addition, the company’s techniques for optical isolation for relays and signal processing offer high voltage isolation between the load side and the system controller. 2 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com CONTENTS Part Number Index High Speed Digital Optical Isolators Numerical Index to all Product Catalog Devices ...............................4 Solid State Relays 1-Form-A Relays...............................................................................7 1-Form-B Relays.............................................................................10 1-Form-A & 1-Form-B Combination Relays ....................................11 1-Form-A Relays: Single-Pole, Normally Open, DC-Only ...............11 1-Form-A Relays: Normally Open, Voltage-Controlled ...................12 1-Form-B Relays: Normally Closed, Voltage-Controlled .................12 2-Form-A Relays: Common Input, Dual Pole, Normally Open ........12 1-Form-C Relays: Common Input ...................................................12 Multifunction Solid State Relays .....................................................13 Fault Protected Relays Current Limited SSRs with Thermal Management (ThM) ...............14 Current Limited SSR with Voltage Triggered Shutdown & ThM ......15 Power Relays 1-Form-A Power Relays: Single-Pole, Bidirectional ........................17 1-Form-A Power Relays: Single-Pole, Unidirectional ......................17 Optically Isolated AC Power Switches Optically Isolated AC Power Switches: ILOAD≤1A .............................18 Optically Isolated AC Power Switches: ILOAD>1A .............................19 Gate Drivers Low-Side Gate Drivers ...................................................................20 IX2113 600V High-Side & Low-Side Gate Driver ...........................21 IX2127 600V High-Side Gate Driver ...............................................21 IX21844 High Voltage Half-Bridge Gate Driver ...............................22 IX2204 Dual Low-Side IGBT Gate Driver .......................................22 IX3120 2.5A Output Optically Coupled Gate Driver .......................23 IX3180 2.5A High Speed Gate Driver Optocoupler ........................23 Optically Isolated Gate Drivers .......................................................24 Optically Isolated Dual MOSFET Gate Drivers ...............................24 High Voltage Products High Voltage Analog Switch Arrays ................................................25 High Voltage Isolated Analog Switches ..........................................26 CPC5001 Single-Channel, Each Direction Digital Optical Isolator .27 CPC5002 Dual High Speed Digital Optical Isolator ........................27 CPC5902 Optically Isolated I2C Bus Repeater ...............................28 CPC5903 Optically Isolated I2C Bus Repeater ...............................29 Optocouplers Optically Isolated Linear Error Amplifiers .......................................29 Single & Dual Optocouplers ...........................................................30 Linear Optocouplers .......................................................................31 Discrete Components N-Channel Depletion Mode FETs...................................................32 Diode Bridges .................................................................................32 Display Products High Voltage LED Drivers ...............................................................33 ePaper Gate & Source Drivers .......................................................34 Telecommunications Products Line Card Access Switches (LCAS) ...............................................36 CPC75282 Dual 6-Pole LCAS ........................................................37 CPC7508 LCAS for Ringing SLIC ..................................................37 LITELINK™ Silicon DAA, Phone Line Interface .............................38 Voltage Monitor Devices .................................................................39 DC Termination ICs (xDSL, ISDN) ..................................................40 Telecom Multifunction Solid State Relays .......................................41 M-949-11 Line Sense Relay ...........................................................41 Cybergate™ Data Access Arrangement (DAA) Module .................42 M-980-02 Call Progress Tone Detector ..........................................43 M-986-2R2 MFC Transceiver ..........................................................43 CPC2400E Embedded Modem Module .........................................44 Other Semiconductor Products MX887D/P Hall Effect Switches......................................................45 Solar Cells ......................................................................................45 MX877 & MX879 Load Drivers .......................................................46 CPC5608 Low Power Transistor Array ............................................46 NCD2100 Non-Volatile Digital Programmable Capacitor ................47 Note: Within the pages of this catalog are drawings and photographs of IXYS Integrated Circuits Division products. These drawings and photographs are for illustrative purposes only, and do not necessarily portray accurate marking or branding. They exist solely to provide additional useful information. +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 3 PART NUMBER INDEX CPC1001N 30 CPC1330 7 CPC1916Y 17 CPC1998J 19 CPC5712 39 IAD110 13 IXDN604 20 CPC1002N 11 CPC1333 10 CPC1918J 17 CPC2014N 9 CPC5902 28 IBB110 13 IXDN609 20 CPC1004N 11 CPC1335 7 CPC1926Y 17 CPC2017N 9 CPC5903 29 ITC117 41 IXDN614 20 CPC1006N 7 CPC1390 7 CPC1927J 17 CPC2025N 9 CPC7220 25 ITC117L 41 IXDN630 20 CPC1008N 7 CPC1393 7 CPC1943 18 CPC2030N 9 CPC7232 25 ITC135 41 IXDN630M 20 CPC1009N 7 CPC1394 7 CPC1945G 18 CPC2125N 10 CPC7508 37 ITC137 41 IXEP1400 34 CPC1014N 7 CPC1465 40 CPC1945Y 18 CPC2317N 11 CPC7512 26 IX2113 21 IXEP2300 34 CPC1016N 7 CPC1466 40 CPC1961 18 CPC2330N 11 CPC7514 26 IX2127 21 LAA100 CPC1017N 7 CPC1510 7, 14 CPC1963 18 CPC2400E 44 CPC75282 37 IX21844 22 LAA100L 9 CPC1018N 7 CPC1540 7, 14 CPC1964B 19 CPC3701 32 CPC7556 32 IX2204 22 LAA108 9 CPC1019N 7 CPC1560 7, 14 CPC1964BX6 19 CPC3703 32 CPC7557 32 IX3120 23 LAA110 9 CPC1020N 7 CPC1563 7, 14 CPC1964G 18 CPC3708 32 CPC7591 36 IX3180 23 LAA110L 9 CPC1025N 7 CPC1580 24 CPC1964Y 18 CPC3710 32 CPC7592 36 IX4423 20 LAA120 9 CPC1030N 7 CPC1590 24 CPC1965G 18 CPC3714 32 CPC7594 36 IX4424 20 LAA120L 9 CPC1035N 7 CPC1593 7, 15 CPC1965Y 18 CPC3720 32 CPC7601 25 IX4425 20 LAA125 9 CPC1106N 10 CPC1706Y 17 CPC1966 19 CPC3730 32 CPC7691 36 IX4426 20 LAA125L 9 CPC1114N 10 CPC1708J 17 CPC1966B 19 CPC3902 32 CPC7692 36 IX4427 20 LAA126 9 CPC1117N 10 CPC1709J 17 CPC1966YX6 19 CPC3909 32 CPC7695 36 IX4428 20 LAA126L 9 CPC1125N 10 CPC1718J 17 CPC1967J 17 CPC3960 32 CPC7701 25 IX9908 33 LAA127 9 CPC1130N 10 CPC1726Y 17 CPC1968J 17 CPC3980 32 CPC9909 33 IXDD604 20 LAA127L 9 CPC1135N 10 CPC1727J 17 CPC1972 18 CPC3982 32 CYG2000 42 IXDD609 20 LAA710 9 CPC1150N 10 CPC1777J 17 CPC1973Y 17 CPC40055ST 19 CYG2011 42 IXDD614 20 LBA110 11 CPC1215 12 CPC1779J 17 CPC1976 19 CPC44055ST 19 CYG2020 42 IXDD630 20 LBA110L 11 CPC1217 12 CPC1786J 17 CPC1976YX6 19 CPC5001 27 CYG2100 42 IXDD630M 20 LBA120 11 CPC1218 12 CPC1788J 17 CPC1977J 17 CPC5002 27 CYG2110 42 IXDF602 20 LBA120L 11 CPC1219 12 CPC1822 45 CPC1978J 17 CPC5601 * CYG2111 42 IXDF604 20 LBA126 11 CPC1225N 7 CPC1824 45 CPC1979J 17 CPC5602 32 CYG2217 42 IXDI602 20 LBA126L 11 CPC1230N 7 CPC1831 45 CPC1981Y 17 CPC5603 32 CYG2218 42 IXDI604 20 LBA127 11 CPC1231N 10 CPC1832 45 CPC1983B 17 CPC5608 46 CYG2320 42 IXDI609 20 LBA127L 11 CPC1301 30 CPC1906Y 17 CPC1983Y 17 CPC5620 38 FDA215 24 IXDI614 20 LBA710 11 CPC1302 30 CPC1907B 17 CPC1983YE 17 CPC5621 38 FDA217 24 IXDI630 20 LBA716 11 CPC1303 30 CPC1908J 17 CPC1986J 17 CPC5622 38 IAA110 13 IXDI630M 20 LBB110 10 CPC1317 7 CPC1909J 17 CPC1988J 17 CPC5710 39 IAB110 13 IXDN602 20 LBB120 10 * See additional information on IXYS Integrated Circuits Division web site: www.ixysic.com 4 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 9 PART NUMBER INDEX 9 PLA194 8 OMA160 8 PLB150 10 PAA110 9 PLB190 10 30 PAA110L 9 PM1204 18 LDA111 30 PAA127 9 PM1205 18 LDA200 30 PAA132 9 PM1206 18 7 LDA201 30 PAA140 9 PS1201 18 7 LDA202 30 PAA140L 9 PS2401 18 LCA125 7 LDA203 30 PAA150 9 PS2601 18 LCA125L 7 LDA210 30 PAA190 9 TS117 13 LCA126 7 LDA211 30 PAA191 9 TS117L 13 LCA127 7 LDA212 30 PAA193 9 TS118 13 LCA127L 7 LDA213 30 PBA150 11 TS120 13 LCA129 8 LIA120 29 PBB150 10 TS122 13 LCA182 8 LIA130 29 PBB190 10 TS190 13 LCA210 12 LOC110 31 PD1201 18 TS190L 13 LCA210L 12 LOC111 31 PD2401 18 XAA117 9 LCA220 12 LOC112 31 PD2601 18 XAA170 9 LCA701 8 LOC117 31 PLA110 8 XBA170 11 LCA710 8 LOC210 31 PLA110L 8 XBB170 10 LCA712 8 LOC211 31 PLA132 8 XCA170 8 LCA715 8 M-949-11 41 PLA134 8 XCB170 10 LCA717 8 M-980-02 43 PLA140 8 XS170 13 LCB110 10 M-986-2R2 43 PLA140L 8 LCB111 10 MX860 35 PLA143 8 LCB120 10 MX877 46 PLA150 8 LCB126 10 MX879 46 PLA160 8 LCB127 10 MX887D 45 PLA170 8 LCB710 10 MX887P 45 PLA171 8 LCB716 10 MXEI1480 35 PLA190 8 LCB717 10 MXEI2240 35 PLA191 8 LCC110 12 MXHV9910 34 PLA192 8 LCC120 12 NCD2100 47 PLA193 8 LBB126 10 LDA100 30 OAA160 LBB127 10 LDA101 30 LCA100 7 LDA102 30 LCA100L 7 LDA110 LCA110 7 LCA110L 7 LCA120 LCA120L * See additional information on IXYS Integrated Circuits Division web site: www.ixysic.com +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 5 SOLID STATE RELAYS The OptoMOS® line of Solid State Relays (SSRs) uses discrete semiconductor components and patented OptoMOS architecture to provide fast, reliable, bounce-free switching in a compact design. From one of the world’s smallest single pole, high voltage, 4-pin relays to multi-pole and multifunction devices, OptoMOS products are an ideal replacement for larger reed and electromechanical relays. Compared to older electromagnetic technologies, OptoMOS relays offer significantly lower drive current, smaller package size, no susceptibility to magnetic interference, and solid state reliability. All of these are key requirements for the design of today’s complex low-power, multi-channel products. Bidirectional Load Load IXYS Integrated Circuits Division Solid State Relays are provided in three main types: Unidirectional (UNI), Bidirectional (BI), and Bidirectional Plus (BI+). A UNI relay conducts load current in only one direction, a BI relay conducts load current in both directions, and a BI+ relay has a provision for connecting the output MOSFETs in such a way that the relay in UNI configuration conducts significantly more load current than when it is wired in BI configuration (see the diagram on this page). The accompanying tables reference these three types for all devices listed. Polarity Independent Unidirectional Load + These three main types are available in a variety of configurations: normally open (1-Form-A), normally closed (1-Form-B), dual 1-Form-A, dual 1-Form-B, 1-Form-A and 1-Form-B in the same package, 1-Form-A and 1-Form-B voltage-controlled relays, 2-Form-A, and 1-Form-C. Load – Polarity Dependent Drawings of all the available packages are shown below. For exact physical dimensions of any package, download the data sheet for the product that you are interested in from the web site page, a link to which is referenced in the note at the bottom of the page. The packages are referred to by number in the accompanying tables. Load Features: Applications: • Low Drive Current • High Reliability • No EMI/RFI Generation • Arc-Free with No Snubbing Circuits • AC or DC Switching • Current Limiting (Available) • FCC Compatible • Low Off-State Leakage • Telecommunications / Datacommunications • Instrumentation • Multiplexers • Data Acquisition / Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment (Patient / Equipment Isolation) • Security • Aerospace • Industrial Controls 6-Pin Surface Mount 10 12 14 Load BI Configuration Polarity Independent + Load – Load UNI Configuration Polarity Dependent 8-Pin DIP 17 20 4-Pin SIP (8-Pin Body) 8-Pin Surface Mount 8-Pin Flatpack Do Not Use 8-Pin SOP 6-Pin DIP 4-Pin SOP Bidirectional Plus 4-Pin DIP 21 22 4-Pin DIP (14-Pin Body) 41 42 6-Pin Flatpack (8-Pin Body) 4-Pin V-DIP 4-Pin Surface Mount 43 44 61 For data sheets, go to www.ixysic.com/Products/ProdList.htm 6 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 62 BI BI+ • 1-Form-A Relays 1-Form-A Relays: Single-Pole, Normally Open Part Number CPC1006N CPC1008N CPC1009N CPC1014N CPC1016N CPC1017N CPC1018N CPC1019N CPC1020N CPC1025N CPC1030N CPC1035N CPC1225N CPC1230N CPC1317 CPC1330 CPC1335 CPC1390 CPC1393 CPC1394 CPC1510 CPC1540 CPC1560 CPC1563 CPC1593 LCA100 LCA100L LCA110 LCA110L LCA120 LCA120L LCA125 LCA125L LCA126 LCA127 LCA127L Relay Type Blocking Voltage Load Current On Resistance BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ (VP) 60 100 100 60 100 60 60 60 30 400 350 350 400 350 70 350 350 400 600 600 250 350 60 600 600 350 350 350 350 250 250 300 300 250 250 250 (mA) 75 150 150 400 100 100 600 750 1200 120 120 100 120 120 150 120 100 140 90 120 200 120 300 120 120 120 120 120 120 170 150 170 170 170 200 170 () 10 8 8 2 16 16 0.8 0.6 0.25 30 30 35 30 30 16 30 35 22 50 35 15 25 5.6 35 35 25 25 35 35 20 20 16 20 15 10 15 Input Control Current (mA) 0.5 2 2 2 2 1 1 2 2 2 2 2 2 2 1 2 1 2 2 2 2 2 1.1 2 2 5 5 2 2 5 5 5 5 5 5 5 Switching Speeds ton / toff (ms) 10 / 10 2/1 2 / 0.5 2/1 2/1 10 / 10 3/2 3/3 3/3 2/1 2/1 2/1 2/1 2/1 2.5 / 2.5 2/1 10 / 10 1/1 5/5 5/3 2/2 2/2 0.1 / 0.4 2/2 2/2 5/5 5/5 3/3 3/3 3/3 3/3 5/5 5/5 5/5 5/5 5/5 Isolation Voltage Off-State Leakage (Vrms) 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 3750 5000 3750 5000 5000 5000 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 (A) 1 1 0.02 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Package Type (Page 6) 10 10 10 10 10 10 10 10 10 10 10 10 10 10 21 42, 43 21 42, 43, 44 42, 43, 44 42, 43, 44 12, 14 12, 14 20, 22 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 Features and Comments Low IF , EN 50130-4 Very Low Off-State ILEAK = 20nA EN 50130-4 Low IF , EN 50130-4 Low IF , EN 50130-4 High Load Current, Very Low On Resistance EN/IEC 60950-1 Supplementary Isolation Voltage (0.4mm Distance Through Isolation) EN/IEC 60950-1 Supplementary Isolation Voltage (0.4mm Distance Through Isolation) EN 50130-4 (Installation Class 3), Transient Voltage Suppression (TVS) Enhanced Isolation Voltage Low IF , EN 50130-4 (Installation Class 3), Transient Voltage Suppression (TVS) Enhanced Isolation Voltage Enhanced Isolation Voltage Enhanced Isolation Voltage Current Limited with Thermal Management - See Page 14 Current Limited with Thermal Management - See Page 14 Current Limited with Thermal Management - See Page 14 Current Limited with Thermal Management - See Page 14 Current Limited, Thermal Management, Voltage Triggered Shutdown - See Page 15 Current Limiting Current Limiting Current Limiting Current Limiting Current Limiting For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 7 BI+ BI 1-Form-A Relays: Single-Pole, Normally Open (Continued) Part Number LCA129 LCA182 LCA701 LCA710 LCA712 LCA715 LCA717 OMA160 PLA110 PLA110L PLA132 PLA134 PLA140 PLA140L PLA143 PLA150 PLA160 PLA170 PLA171 PLA190 PLA191 PLA192 PLA193 PLA194 XCA170 Relay Type Blocking Voltage Load Current On Resistance BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI BI+ BI+ BI+ BI+ BI+ BI+ (VP) 250 350 100 60 60 60 30 250 400 400 60 100 400 400 600 250 300 800 800 400 400 600 600 600 350 (mA) 170 120 1500 1000 1000 2200 2000 50 150 150 600 350 250 200 100 250 50 100 100 150 250 150 100 130 100 () 20 35 0.3 0.5 0.5 0.15 0.15 100 22 25 1 3 8 13 50 7 100 50 50 22 8 22 50 35 50 Input Control Current (mA) 2 0.25 2 10 10 5 2 10 5 5 2 5 5 5 2 5 10 5 2 5 5 5 5 2 5 Switching Speeds ton / toff (ms) 8/8 3/3 4/1 2.5 / 0.25 2.5 / 0.35 2.5 / 0.25 3/3 0.125 / 0.125 1 / 0.5 1 / 0.25 5/2 5/5 3/1 5/3 5/5 2.5 / 0.5 0.05 / 0.05 5/5 5/5 1 / 0.5 3/1 5/5 5/5 3/2 5/5 Isolation Voltage Off-State Leakage (Vrms) 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 4000 3750 3750 3750 5000 5000 5000 5000 5000 5000 3750 (A) 1 1 1 1 0.01 1 1 0.025 1 1 1 1 1 1 1 0.025 1 1 1 1 1 1 1 1 Package Type (Page 6) Features and Comments 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 62 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 1-Form-A Relays: CPC7514 Quad Single-Pole, Normally Open See Page 26 for full details. The CPC7514 Quad High Voltage Isolated Analog Switch Array provides the switching functionality of four independent 1-Form-A relays in a single small economical package. Designed to provide flexible single-ended or differential access to high voltage networks, up to ±320V, the CPC7514 is configured as two sets of matched-pair switches. The CPC7514 is self-biasing, and requires no external power supply. Shown to the right is one 2-switch channel. Very Low IF High Load Current High Load Current High Load Current, Low ILEAK High Load Current High Load Current Low ILEAK , Fast Switching Times Current Limiting Current Limiting Enhanced Isolation Voltage Low ILEAK , Fast Switching Times Enhanced Isolation Voltage (7mm Output Pin Separation) Enhanced Isolation Voltage Enhanced Isolation Voltage Enhanced Isolation Voltage, PLA192E is DIN EN 60747-5-5 Certified Enhanced Isolation Voltage, PLA193E is DIN EN 60747-5-5 Certified Enhanced Isolation Voltage 1/2 CPC7514 S3B S4 * S4A IN3 IN4 LATCH2 S4B L A T C H 2 TSD2 For data sheets, go to www.ixysic.com/Products/ProdList.htm 8 S3* S3A IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com Channel 3-4 S3 Switch Control Logic S4 * ±320V BI 1-Form-A Relays: Dual Single-Pole, Normally Open Part Number CPC2014N CPC2017N CPC2025N CPC2030N LAA100 LAA100L LAA108 LAA110 LAA110L LAA120 LAA120L LAA125 LAA125L LAA126 LAA126L LAA127 LAA127L LAA710 OAA160 PAA110 PAA110L PAA127 PAA132 PAA140 PAA140L PAA150 PAA190 PAA191 PAA193 XAA117 XAA170 Relay Type Blocking Voltage Load Current On Resistance BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI (VP) 60 60 400 350 350 350 100 350 350 250 250 350 350 250 250 250 250 60 250 400 400 280 60 400 400 250 400 400 600 60 350 (mA) 400 120 120 120 120 120 300 120 120 170 150 170 150 170 170 200 170 1000 50 150 150 200 600 250 200 250 150 250 100 150 100 () 2 16 30 30 25 25 8 35 35 20 25 16 18 15 20 10 15 0.5 100 22 25 10 1 8 13 7 22 8 50 16 50 Input Control Current (mA) 2 1 2 2 5 5 2 5 5 5 5 5 5 5 5 5 5 10 3 5 5 3 2 5 5 5 5 5 5 1 5 Switching Speeds ton / toff (ms) 2/1 3/3 2/1 2/1 5/5 5/5 3/3 3/3 3/3 5/5 5/5 5/5 5/5 5/5 5/5 5/5 5/5 2.5 / 0.25 0.125 / 0.125 1 / 0.25 1 / 0.5 0.5 / 0.5 5/2 3/1 5/3 2.5 / 0.5 1 / 0.5 3/1 5/5 5/5 5/5 Isolation Voltage Off-State Leakage (Vrms) 1500 1500 1500 1500 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 5000 5000 5000 3750 3750 (A) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0.025 1 1 0.025 1 1 1 1 1 1 10 1 1 Package Type (Page 6) 17 17 17 17 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 20, 22 20, 21, 22 20, 22 20, 22 20, 22 20, 21, 22 20, 21, 22 Features and Comments EN 50130-4 Low IF , EN 50130-4 Current Limiting Current Limiting Current Limiting Current Limiting Current Limiting Current Limiting Very Low ILEAK , Fast Switching Times Current Limiting Very Low ILEAK , Fast Switching Times Current Limiting Enhanced Isolation Voltage Enhanced Isolation Voltage Enhanced Isolation Voltage Low IF For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 9 • 1-Form-B Relays NEW ! BI BI+ 1-Form-B Relays: Single-Pole, Normally Closed Relay Type Blocking Voltage Load Current On Resistance CPC1106N BI (VP) 60 (mA) 75 CPC1114N CPC1117N CPC1125N CPC1130N CPC1135N CPC1150N CPC1231N CPC1333 LCB110 LCB111 LCB120 LCB126 LCB127 LCB710 LCB716 LCB717 PLB150 PLB190 XCB170 BI BI BI BI BI BI BI BI BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ 60 60 400 350 350 350 350 350 350 350 250 250 250 60 60 30 250 400 350 400 150 100 120 120 120 120 130 120 120 170 170 200 1000 500 1500 250 130 100 Part Number Switching Speeds ton / toff (ms) 10 / 10 Isolation Voltage Off-State Leakage () 10 Input Control Current (mA) 0.5 Package Type (Page 6) (Vrms) 1500 (A) 1 10 2 16 35 30 35 50 30 30 35 35 20 15 10 0.6 2 0.3 7 25 50 2 1 2 2 2 2 2 2 5 2 5 5 5 2 2 2 5 2 5 2/5 10 / 10 2/2 2/2 2/2 1/2 2/2 2/3 3/3 5/5 5/5 5/5 5/5 3/3 3/3 2/5 1 / 2.5 1 / 2.5 5/5 1500 1500 1500 1500 1500 1500 1500 5000 3750 3750 3750 3750 3750 3750 3750 3750 3750 5000 3750 1 1 5 5 5 5 5 1 1 1 1 1 1 1 1 1 1 1 1 10 10 10 10 10 10 10 42, 43 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 Features and Comments Low IF , EN 50130-4 Low IF , EN 50130-4 EN/IEC 60950-1 Supplementary Isolation Voltage (0.4mm Distance Through Isolation) Enhanced Isolation Voltage High Load Current High Load Current Enhanced Isolation Voltage BI 1-Form-B Relays: Dual Single-Pole, Normally Closed Part Number CPC2125N LBB110 LBB120 LBB126 LBB127 PBB150 PBB190 XBB170 Relay Type Blocking Voltage Load Current On Resistance BI BI BI BI BI BI BI BI (VP) 400 350 250 250 250 250 400 350 (mA) 100 120 170 170 200 250 130 100 () 35 35 20 15 10 7 25 50 Input Control Current (mA) 2 5 5 5 5 5 2 5 Switching Speeds ton / toff (ms) 2/2 3/3 5/5 5/5 5/5 2.5 / 2.5 1 / 2.5 5/5 Isolation Voltage Off-State Leakage (Vrms) 1500 3750 3750 3750 3750 3750 5000 3750 (A) 5 1 1 1 1 1 1 1 Package Type (Page 6) Features and Comments 17 20, 21, 22 20, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm 10 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com BI • 1-Form-A & 1-Form-B Combination Relays Part Number CPC2317N CPC2330N LBA110 LBA110L LBA120 LBA120L LBA126 LBA126L LBA127 LBA127L LBA710 LBA716 PBA150 XBA170 Relay Type Blocking Voltage Load Current On Resistance BI BI BI BI BI BI BI BI BI BI BI BI BI BI (VP) 60 350 350 350 250 250 250 250 250 250 60 60 250 350 (mA) 120 120 120 120 170 150 170 150 200 150 1000 1000 250 100 () 16 30 35 35 20 25 15 20 10 15 0.6 0.4 7 50 Input Control Current (mA) 1 2 2 5 5 5 5 5 5 5 2 2 5 2 Switching Speeds ton / toff (ms) 3/3 3/3 3/3 3/3 5/5 5/5 5/5 5/5 5/5 5/5 5/5 5/5 2.5 / 2.5 5/5 Isolation Voltage (Vrms) 1500 1500 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 Off-State Leakage A/B (A) 1/1 1/5 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 Package Type (Page 6) 17 17 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 20, 22 20, 21, 22 20, 22 20, 22 20, 22 20, 22 20, 21, 22 Features and Comments Low IF Current Limiting Current Limiting Current Limiting Current Limiting High Load Current High Load Current UNI • 1-Form-A Relays: Single-Pole, Normally Open, Unidirectional (DC-Only) Part Number CPC1002N CPC1004N Relay Type Blocking Voltage Load Current On Resistance UNI UNI (VP) 60 100 (mA) 700 300 () 0.55 4 Input Control Current (mA) 2 2 Switching Speeds ton / toff (ms) 5/2 3/1 Isolation Voltage Off-State Leakage (Vrms) 1500 1500 A) 1 1 Package Type (Page 6) 10 10 Features and Comments EN 50130-4 Extended Operating Temperature Range: -40ºC to +110ºC For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 11 BI • 1-Form-A Relays: Single-Pole, Normally Open, Voltage-Controlled Part Number CPC1215 CPC1217 CPC1218 Relay Type Blocking Voltage Load Current On Resistance BI BI BI (VP) 400 60 60 (mA) 500 200 600 () 6 16 1.1 Input Control Voltage (V) 5 - 12 5 - 12 5 - 12 Switching Speeds ton / toff (ms) 5/3 5/5 5/5 Isolation Voltage Off-State Leakage (Vrms) 3750 2500 2500 (A) 1 1 1 Package Type (Page 6) 61 41 41 Features and Comments Direct drop-in reed relay replacement EN 50130-4, Direct drop-in reed relay replacement EN 50130-4, Direct drop-in reed relay replacement BI • 1-Form-B Relays: Single-Pole, Normally Closed, Voltage-Controlled Part Number CPC1219 Relay Type BI Blocking Voltage Load Current On Resistance Switching Speeds ton / toff (ms) Isolation Voltage Off-State Leakage () Input Control Voltage (V) (VP) (mA) 60 200 (Vrms) (A) 16 5 - 12 5/5 2500 1 Package Type (Page 6) Features and Comments 41 EN 50130-4, Direct drop-in reed relay replacement BI • 2-Form-A Relays: Common Input, Dual-Pole, Normally Open Part Number LCA210 LCA210L LCA220 Relay Type Blocking Voltage Load Current On Resistance BI BI BI (VP) 350 350 250 (mA) 85 85 120 () 35 35 20 Input Control Current (mA) 8 8 10 Switching Speeds ton / toff (ms) 3/3 4/4 5/5 Isolation Voltage Off-State Leakage (Vrms) 3750 3750 3750 (A) 1 1 1 Package Type (Page 6) Features and Comments 20, 22 20, 22 20, 22 Current Limiting BI • 1-Form-C Relays: Common Input Part Number LCC110 LCC120 Relay Type Blocking Voltage Load Current On Resistance BI BI (VP) 350 250 (mA) 120 170 () 35 20 Input Control Current (mA) 8 10 Switching Speeds ton / toff (ms) 4/4 5/5 Isolation Voltage Off-State Leakage (Vrms) 3750 3750 (A) 1 1 Package Type (Page 6) Features and Comments 20, 21, 22 20, 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm 12 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com • Multifunction Solid State Relays The OptoMOS line of Multifunction SSR Products combines several optically isolated discrete component functions into a single package. These products mix and match solid state relays, optocouplers, and Darlington transistors to create highly functional circuits in a single, small package. Multifunction devices allow designers to consolidate circuit functions into a single device, freeing up valuable board space and reducing component count. Features: Applications: • 3750Vrms Input to Output Isolation • Multiple Functionality in a Single Package • Current Limiting (Part Numbers with “L” Suffix) • Machine Insertable, Wave Solderable • TTL and CMOS Compatible • Telecommunication / Datacommunication • Instrumentation • I/O Subsystems / Electronic Switching • Medical Equipment (Patient / Equipment Isolation) • Security • Aerospace • Industrial Controls A B E Relay Characteristics Part Number Style IAA110 IAB110 IAD110 IBB110 TS117 TS117L TS118 TS120 TS122 TS190 TS190L XS170 B C A D E E F G E E E E F D G Optocoupler Characteristics Blocking Voltage Current Handling On Resistance (VP) 350 350 350 350 350 350 350 350 250 400 400 350 (mA) 100 100 100 100 120 120 120 120 170 150 150 100 () 35 35 35 35 35 35 35 35 20 22 25 50 Input Control Current (mA) 5 5 5 5 2 2 5 5 5 5 5 2 16-Pin Low-Profile SOIC 4 C Breakdown Voltage (V) 20 20 20 20 20 20 20 20 20 20 20 20 Current Transfer Ratio (%) 33 33 33 33 33 33 33 300 33 33 33 33 Saturation Voltage (V) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 0.5 0.5 0.5 0.5 Input Control Current (mA) 6 6 6 6 6 6 6 2 6 6 6 6 8-Pin DIP 20 Isolation Voltage Package Type (Vrms) 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 4 4 4 4 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 21 20, 21, 22 Features and Comments Two 1-Form-A Relays, One Optocoupler One 1-Form-A Relay, One 1-Form-B Relay, One Optocoupler One 1-Form-A Relay, Two Optocouplers Two 1-Form-B Relays, One Optocoupler One 1-Form-A Relay, One Optocoupler One Current-Limiting 1-Form-A Relay, One Optocoupler One 1-Form-B Relay, One Optocoupler One 1-Form-A Relay, One Darlington Optocoupler One 1-Form-A Relay, One Optocoupler One 1-Form-A Relay, One Optocoupler One Current-Limiting 1-Form-A Relay, One Optocoupler One 1-Form-A Relay, One Optocoupler 8-Pin Flatpack 21 8-Pin Surface Mount 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 13 FAULT PROTECTED RELAYS • Current Limited SSRs with Thermal Management (ThM) These specialized OptoMOS relays are single-pole, current limited, normally open (1-Form-A) Solid State Relays that can replace electromechanical relays in many critical industrial and commercial applications. They are constructed using a highly efficient infrared LED for actuation control and an integrated monolithic die for the switch output. The active current-limit circuitry in these relays also has a thermal management feature that provides excellent power-cross immunity for improved survivability in harsh environments. These features greatly improve the robustness of end systems that use these devices when compared to systems using relays without integrated current limit. These devices may be used in both unidirectional DC applications and bidirectional AC applications. CPC1540 and CPC1563 incorporate an additional fault feature, Voltage Triggered Shutdown (VTS), that quickly shuts the device down if a high voltage transient, >100V, occurs in the load while current limiting is in effect. These two devices are ideal for use in noisy environments where such transients can be expected. Features: Applications: • Integrated Active Current-Limit • Thermal Management • Low Input Control Current • Low Drive Power Requirements • 3750Vrms Isolation, Input-to-Output • Telephony Hook Switch • VoIP Gateways • I/O Subsystems • Electronic Switching • Medical Equipment (Patient / Equipment Isolation) Part Number CPC1510 CPC1540 CPC1560 CPC1563 Blocking Voltage Input Control Current On Resistance (Maximum) Load Current (Maximum) Current Limit (Maximum) DC-Only AC DC-Only AC DC-Only AC * VTS Threshold • Security • Aerospace • Industrial Controls Switching Speed Isolation Voltage Package Type Features & Comments ton / toff (VP) (mA) () () (mA) (mA) (mAP) (mAP) (V) (ms) (Vrms) 250 350 60 600 2 2 1.1 2 3.75 6.75 1.4 11.75 15 25 5.6 35 350 250 600 250 200 120 300 120 920 570 1500 570 450 285 900 285 100 100 2/2 2/2 0.1 / 0.4 2/2 3750 3750 3750 3750 12, 14 12, 14 20, 22 12, 14 Industrial Applications PSTN Hook Switch Applications Fast Switching Speeds High Blocking Voltage * Provides additional current limiting after primary current limit has been enabled due to a fault condition. CPC1510 6-Pin Surface Mount 6-Pin DIP Gate Drive Control Thermal Management 12 14 8-Pin Surface Mount 8-Pin DIP 20 For data sheets, go to www.ixysic.com/Products/ProdList.htm 14 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 22 • Current Limited SSR with Voltage Triggered Shutdown & Thermal Management The new CPC1593 OptoMOS solid state relay (SSR) adds a special Voltage Triggered Shutdown (VTS) feature to current limiting and thermal management. The 21V VTS level, if enabled during current limiting, shuts the switch down, thus limiting the power dissipated by the switch, and preventing damage to the device due to extended fault conditions. CPC1593 OUT1 Gate Drive Control The CPC1593 is designed for use in AC environments where fault conditions can persist for long periods of time, and where, upon removal of the fault, return to normal operation is expected. The CPC1593 is designed to survive extended power-cross conditions. Thermal Management When all fault conditions have been removed, the CPC1593 recommences normal operation, and automatically resets all of its protection circuits. No intervention is necessary. Part Number CPC1593 Blocking Voltage (VP) 600 On Resistance (Maximum) Load Current (Maximum) Current Limit (Maximum) DC-Only AC DC-Only AC DC-Only AC () 11.75 () 35 (mA) 250 (mA) 120 (mAP) 570 (mAP) 285 Input Control Current OUT1 Voltage Triggered Shutdown (VTS) This three-level, self-resetting fault scheme not only protects the CPC1593’s load, but also helps to protect the CPC1593 itself, thus creating a highly effective switching mechanism that can survive in the harshest operating environments. S1 OUT2 S2 S1 S2 OUT2 Switching Speed Isolation Voltage * VTS Threshold Package Type (Vrms) 3750 (V) 21 12, 14 Features & Comments ton / toff (mA) 2 (ms) 2/2 Power Supply Start-Up * Provides additional current limiting after primary current limit has been enabled due to a fault condition. Voltage Threshold Shutdown Delay VTH Voltage Threshold Reactivation Delay ILMT Features: Time • 600VP Blocking Voltage • Integrated Active Current-Limit • Integrated Thermal Management • Integrated Voltage Triggered Shutdown res l! Ensu Surviva ross C r e Pow 6-Pin Surface Mount 6-Pin DIP ILMT 12 VTH 14 Current Through Switch Note: Performance into resistive load. Line Voltage For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 15 POWER RELAYS IXYS Integrated Circuits Division’s line of power relays features OptoMOS technology, reliability, and compact size in the Power SOIC, Power SIP, i4-PAC™ and ISOPLUS™-264 series of power solid state relays. Development of these products was founded on the blending of our traditional strengths in the design and manufacture of photovoltaic integrated circuits (ICs), leadframe design, and multi-chip packaging with IXYS’ expertise in power MOSFETs, power packages, and substrate technology. Our Power Relays are now offered in four package types, which offer between 2500Vrms and 5000Vrms of input to output isolation. The Power SIP package offers pin-to-pin compatibility with other solid state relays providing an easy upgrade path for existing designs, and compatibility for new designs. The i4-PAC and the ISOPLUS-264 packages feature a unique assembly process whereby the silicon is soft soldered onto a Direct Copper Bond (DCB) substrate rather than traditional bonding onto an epoxy encapsulated copper frame. This structure allows for a substantially lower junction-to-case thermal impedance when compared to conventionally assembled power relays. The i4-PAC package has a thermal resistance of 0.35°C/W while the ISOPLUS-264 package has an even lower thermal impedance of 0.30°C/W. Our Power SSRs are provided in two types: Unidirectional (UNI) and Bidirectional (BI). The polarity independent BI relay conducts load current in both directions, while the polarity dependent UNI relay conducts load current in only one direction. The accompanying tables reference these two types for all devices listed. On the back of the i4-PAC and ISOPLUS-264 packages, the metallized external surface of the DCB substrate maintains 2500Vrms isolation to the device’s internal structure and all external pins. This electrically isolated, low thermal impedance pad makes the new i4-PAC and ISOPLUS-264 power relays an ideal solution for power applications preferring a non-biased heat sink with superior thermal management properties. Features: Applications: • Handles Loads up to 32A • Voltage Ratings up to 1000VP • Low On Resistance • Isolated, Low Thermal Impedance Pad for Heat Sink Applications • Industry Standard 4-Pin SIP Package • Low Input Control Current • Low Thermal Impedances: 0.30°C/W - ISOPLUS-264 0.35°C/W - i4-PAC 1.50°C/W - Power SIP • Robotics • Medical Equipment • Railroad / Traffic Controls • Consumer Appliances • Industrial Control • Test and Measurement Equipment 66 - Power SOIC Metallized External DCB Surface 36 - Power SIP 37 - ISOPLUS-264 For data sheets, go to www.ixysic.com/Products/ProdList.htm 16 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 29 - i4-PAC BI NEW ! • 1-Form-A Power Relays: Single-Pole, Bidirectional Part Number Relay Type (VP) CPC1906Y CPC1907B CPC1908J CPC1909J CPC1916Y CPC1918J CPC1926Y CPC1927J CPC1967J CPC1968J CPC1973Y CPC1977J CPC1978J CPC1979J CPC1981Y CPC1983B CPC1983Y CPC1983YE CPC1986J CPC1988J BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI Load Current (Arms) Free Air 5ºC/W Heat Sink TC=25ºC () Input Control Current (mA) 2 6 3.5 6.5 2.5 5.25 0.7 2.7 1.35 2 0.35 1.25 0.75 1.4 0.18 0.5 0.5 0.5 0.65 0.9 8.5 15 13 6.7 3.35 5 3.1 1.85 3.5 1.6 2.25 15 15 15 15 13.15 15 12.25 7.25 14.5 6.5 9.4 0.3 0.06 0.3 0.1 0.34 0.1 1.4 0.2 0.85 0.35 5 1 2.3 0.75 18 6 6 6 3 2.5 10 5 10 10 10 10 10 10 10 10 10 10 10 10 10 5 5 5 10 10 Blocking Voltage 60 60 60 60 100 100 250 250 400 500 400 600 800 600 1000 600 600 600 1000 1000 On Resistance Switching Speeds ton / toff (ms) Isolation Voltage Off-State Leakage (Vrms) (A) 10 / 5 5/1 20 / 5 25 / 10 5/3 25 / 10 10 / 10 25 / 10 20 / 5 20 / 5 5/3 20 / 5 20 / 5 25 / 5 10 / 5 5/2 5/2 5/2 20 / 5 20 / 5 2500 5000 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 5000 2500 4000 2500 2500 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Package Type (Page 16) Features & Comments 36 66 29 37 36 37 36 37 29 37 36 29 29 37 36 66 36 36 29 37 Enhanced Isolation Voltage Enhanced Isolation Voltage Enhanced Isolation Voltage UNI • 1-Form-A Power Relays: Single-Pole, Unidirectional Part Number Relay Type Blocking Voltage (VP) CPC1706Y CPC1708J CPC1709J CPC1718J CPC1726Y CPC1727J CPC1777J CPC1779J CPC1786J CPC1788J UNI UNI UNI UNI UNI UNI UNI UNI UNI UNI 60 60 60 100 250 250 600 600 1000 1000 Load Current (A) On Resistance Free Air 5ºC/W Heat Sink TC=25ºC () Input Control Current (mA) 4 4 9 6.75 1 3.4 1.5 1.65 0.65 1 11.85 22.8 17.5 8.6 4.6 4.12 1.75 2.45 24 32 32 20 15 15 6.9 10.3 0.09 0.08 0.05 0.075 0.75 0.09 0.5 0.4 2 1.25 5 10 10 10 10 10 10 10 10 10 Switching Speeds ton / toff (ms) Isolation Voltage Off-State Leakage (Vrms) (A) 5/2 20 / 5 20 / 5 20 / 5 5/2 20 / 5 20 / 5 20 / 5 20 / 5 20 / 5 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 1 1 1 1 1 1 1 1 1 1 Package Type (Page 16) Features & Comments 36 29 37 37 36 37 29 37 29 37 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 17 OPTICALLY ISOLATED AC POWER SWITCHES • Optically Isolated AC Power Switches: ILOAD ≤1A The OptoMOS line of power products uses dual power-SCR outputs to produce an alternative to optocoupler and Triac circuits. These AC Power Switches provide a blocking voltage of up to 800VP . In addition, tightly controlled zero-cross circuitry ensures switching of AC loads while minimizing the generation of transients. The input and output circuits are optically coupled to provide 3750Vrms of isolation and noise immunity between control and load circuits. Long life and environmental integrity make these power switches ideal for controlling a variety of AC circuits in industrial environments where electromagnetic interference would disrupt the operation of electromechanical relays. Features: Applications: • Load Current up to 1Arms • Blocking Voltage up to 800VP • 5mA Input Sensitivity • Zero-Cross Turn-On Switching Speed ≤ ½ Cycle Low EMI and RFI Generation • DC Control, AC Switching • Optically Isolated • TTL and CMOS Compatible • High Noise Immunity • Machine Insertable, Wave Solderable • Programmable Controls • Process Control • Power Control Panels • Remote Switching • Gas Pump Electronics • Large Relay Control Circuits • Contactors • Solenoids • Motor Controls • Heater Controls ZC Zero-Cross Turn-On NEW ! 4-Pin DIP (16-Pin Body) Part Number Blocking Voltage Load Current (VP) (Arms) Input Control Current (mA) Operating Frequency Min / Max (Hz) Isolation Voltage Package Type CPC1943 400 0.5 5 20 - 500 3750 15, 16 CPC1945G CPC1945Y CPC1961 CPC1963 CPC1964G CPC1964Y CPC1965G CPC1965Y CPC1972 PD1201 PD2401 PD2601 PM1204 PM1205 PM1206 PS1201 PS2401 PS2601 400 400 600 600 800 800 600 600 800 400 500 600 400 500 600 400 500 600 1 1 0.25 0.5 1 1 1 1 0.25 1 1 1 0.5 0.5 0.5 1 1 1 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 20 - 400 20 - 400 20 - 500 20 - 500 20 - 500 20 - 500 20 - 400 20 - 400 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 3750 3750 3750 3750 2500 2500 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 2 23 20, 22 15, 16 2 23 2 23 12, 14 2 2 2 15, 16 15, 16 15, 16 23 23 23 2 12 (Vrms) 6-Pin Power DIP 6-Pin DIP 14 15 6-Pin Power DIP Surface Mount 8-Pin DIP 16 20 8-Pin Surface Mount 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm 18 6-Pin Surface Mount IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 4-Pin SIP (8-Pin Body) 23 • Optically Isolated AC Power Switches: ILOAD >1A Our solid state AC Power Switches have blocking voltages up to 800V, and are capable of handling very high load currents. These robust AC Power Switches, with their tightly controlled zero-cross circuitry, ensure AC load switching while minimizing the generation of transients. Devices noted as “Rapid Turn-On” in the table below do not include zero-cross circuitry, and are therefore ideal for switching AC loads independent of the load voltage phase. Optically coupled input and output circuits provide up to 5000Vrms of isolation and noise immunity between control and load circuits. These arc-free, heavy-duty AC power switches are ideal for controlling a variety of AC circuits in industrial environments where electromagnetic interference would disrupt the operation of electromechanical relays or where explosive atmospheres exist. Features: Applications: • Load Current up to 50Arms • Blocking Voltage up to 800VP • Zero-Cross Turn-On Low EMI and RFI Generation Switching Speed ≤ ½ Cycle • Non-Zero-Cross Turn-On Switching Speed <500s • 5mA Input Sensitivity • High Noise Immunity • DC Control, AC Switching • Optically Isolated I/O • TTL and CMOS Compatible • Machine Insertable, Wave Solderable • Programmable Controls • Process Control • Power Control Panels • Remote Switching • Gas Pump Electronics • Contactors • Large Relay Control Circuits • Solenoids • Motor Controls • Heater Controls • Lighting Zero-Cross Turn-On R 64 - SuperSIP 29 - i4-PAC ZC Rapid Turn-On (Non-Zero-Cross) 36 - Power SIP 66 - Power SOIC Part Number CPC1964B CPC1964BX6 CPC1966 CPC1966B CPC1966YX6 CPC1976 CPC1976YX6 CPC1998J CPC40055ST CPC44055ST Blocking Voltage (VP) 800 600 600 800 600 600 600 800 800 800 Load Current No Heat Sink (Arms) 1.5 1.5 3 3 3 2 2 5 5 5 5ºC/W Heat Sink (Arms) 20 20 20 TC=25ºC (Arms) 50 40 40 Input Control Current Input Control Voltage Operating Frequency Min / Max (mA) 5 5 5 5 5 5 5 5 5 - (V) 9 - 16 (Hz) 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 Turn-On: Zero-Cross or Rapid Zero-Cross Rapid Zero-Cross Zero-Cross Rapid Zero-Cross Rapid Zero-Cross Zero-Cross Zero-Cross Switching Speed ton / toff Isolation Voltage Package Type (max) ½ Cycle 500s / ½ Cycle ½ Cycle ½ Cycle 500s / ½ Cycle ½ Cycle 500s / ½ Cycle ½ Cycle ½ Cycle ½ Cycle (Vrms) 5000 5000 3750 5000 3750 3750 3750 2500 2500 2500 66 66 36 66 36 36 36 29 64 64 NEW ! Features Enhanced Isolation Voltage, 12.5mm Creepage Rapid Turn-On, Enhanced Isolation Voltage Enhanced Isolation Voltage Rapid Turn-On Rapid Turn-On High Load Current High Load Current, 9.5mm Creepage High Load Current, 9.5mm Creepage For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 19 GATE DRIVERS These ultra-fast, high current MOSFET and IGBT gate drivers are optimized for high efficiency performance in motor drive and power conversion applications. With output current ratings of 1.5A to 30A, they are designed to switch the largest MOSFETs and IGBTs with minimum switching times and at frequencies up to 10MHz. Depending on the output current rating, these gate drivers are offered in DFN (56), SOIC (54), Power SOIC (53), DIP (20), TO-220 (57), and TO-263 (58) packages. “F” versions include one inverting driver and one non-inverting driver, “I” versions are inverters, “N” versions are non-inverters, and “D” versions are non-inverters that include an enable function. Features: • Low-Side Gate Drivers 14SI 6 _ D X I d n a _609SI, D X I , A I S & d! IXD_604SI e AEC Q100 Qualifie ar Part Number Output Type IX4423 IX4424 IX4425 IX4426 IX4427 IX4428 IXD_602 IXD_604 IXD_609 IXD_614 IXD_630 IXD_630M DUAL DUAL DUAL DUAL DUAL DUAL DUAL DUAL SINGLE SINGLE SINGLE SINGLE IPEAK TC=25ºC (AP) 3 3 3 1.5 1.5 1.5 2 4 9 14 30 30 Output Resistance () 4 4 4 9 9 9 4 2.5 1 0.8 0.4 0.4 Available Logic Configurations I N F I N F F, I, N F, I, N, D I, N, D I, N, D I, N, D I, N, D Enable Function • (D) • (D) • (D) • (D) • (D) Undervoltage Lockout (V) VCC < 12.5 VCC < 9 • 1.5A to 30A Peak Source / Sink Drive Current • Wide Operating Voltage Range: 4.5V to 35V • -40°C to +125°C Extended Operating Temperature Range • Logic Input Withstands Negative Swing of up to -5V • Matched Rise and Fall Times • Low Propagation Delay Time • Low 10A Supply Current • Low Output Impedance NEW ! Package Type Applications: • Efficient Power MOSFET and IGBT Switching • Switch Mode Power Supplies • Motor Controls • DC to DC Converters • Class-D Switching Amplifiers • Pulse Transformer Driver 54 54 54 54, 56 54, 56 54, 56 20, 53, 54, 56 20, 53, 54, 56 20, 53, 54, 56, 57, 58 20, 53, 57, 58 57, 58 57, 58 8-Pin DIP 8-Pin Power SOIC 20 53 8-Pin SOIC ENA INA A OUTA INA A OUTA INA A OUTA INA 8-Pin DFN 56 54 A OUTA B OUTB 5-Pin TO-220 ENB INB B OUTB INB F B OUTB INB I B OUTB INB N 5-Pin TO-263 57 D EN IN OUT IN OUT IN OUT For data sheets, go to www.ixysic.com/Products/ProdList.htm 20 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 58 • IX2113 600V High-Side & Low-Side MOSFET and IGBT Gate Driver The IX2113 is a high voltage integrated circuit that can drive high speed MOSFETs and IGBTs that operate at up to +600V. The IX2113 is configured with independent high-side and low-side referenced output channels, both of which can source and sink 2A. The floating high-side channel can drive an N-channel power MOSFET or IGBT 600V from the common reference. IX2113 is supplied in a 16-pin SOIC package or a 14-pin DIP package. VDD HIN SD NEW ! IX2113 Input Control Logic & Cycle-by-Cycle Edge-Triggered Shutdown Level Shift VDD / VCC VSS / COM VB Pulse Generator High Voltage Level Shift UVLO R S R Q Buffer HO Level Shift VDD / VCC VSS / COM VSS LS Delay Control • Floating Channel for Bootstrap Operation up to 600V with an Absolute Maximum Rating of 700V • Outputs Capable of Sourcing and Sinking 2A • Gate Drive Supply Range From 10V to 20V • Enhanced Robustness due to SOI Process • Tolerant to Negative Voltage Transients: dV/dt Immune • 3.3V Logic Compatible • Undervoltage Lockout for Both High-Side and Low-Side Outputs • Matched Propagation Delays VS VCC UVLO LIN Features: Buffer LO COM • IX2127 600V High-Side MOSFET and IGBT Gate Driver The IX2127 is a high voltage, high speed power MOSFET and IGBT driver. The device’s high voltage level-shift technique enables it to operate at up to 600V. Proprietary common-mode design techniques provide stable operation in high dV/dt noise environments. The IX2127 detects an over-current condition in the driven MOSFET or IGBT device, and shuts down drive to that device. An open-drain output, FAULT, indicates that an over-current shutdown has occurred. The gate driver output typically can source 250mA and sink 500mA, which is suitable for fluorescent lamp ballast, motor control, SMPS, and other converter drive topologies. Available in 8-pin DIP and 8-pin SOIC packages. Features: • Floating Channel Designed for Bootstrap Operation up to 600V • Tolerant to Negative Transient Voltages; dV/dt Immune • Undervoltage Lockout • 3.3V, 5V, and 12V Input Logic Compatible • Open-Drain FAULT Indicator Pin Shows Over-Current Shutdown • Output in Phase with the Input IX2127 VCC Low Side Buffer IN Data Latch Transmitter Low-High Level Shift HO Receiver Enable VS 8-Pin DIP Applications: • High Speed Gate Driver • Motor Drive Inverter VB Undervoltage Lockout High Side Blanking Signal Delay FAULT Q Enable R Receiver 8-Pin SOIC COM S High-Low Level Shift Transmitter + Data Latch _ CS Comparator For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 21 • IX21844 High Voltage Half-Bridge Gate Driver The IX21844 is a high voltage IC that can drive high speed MOSFETs and IGBTs that operate at up to +600V. The IX21844 is configured with dependent high-side and low side referenced output channels that can source 1.4A and sink 1.8A. The floating high-side channel can drive an N-channel power MOSFET or IGBT 600V from the common reference. A programmable dead-time can be set between 400ns and 5s to ensure that both the high-side and low-side power MOSFET or IGBT are not enabled at the same time. Features: • Floating Channel for Bootstrap Operation to +600V with an Absolute Maximum Rating of +700V • Programmable Dead Time • Outputs Can Source 1.4A and Sink 1.8A • Gate Drive Supply Range From 10V to 20V • Tolerant to Negative Voltage Transients: dV/dt Immune • 3.3V and 5V Logic Compatible • Undervoltage Lockout for Both High-side and Low-Side Outputs • Matched Propagation Delays NEW IX21844 Typical Application ! VCC VCC up to 600V HO VB IN IN SD SD VS LOAD DT Applications: RDT • Switch Mode Power Supplies • Motor Driver Inverters • DC/DC Converters • Uninterruptable Power Supplies (UPS) VSS COM VSS LO • IX2204 Dual Low Side IGBT Gate Driver The IX2204 is a dual high current gate driver specifically designed to drive the gates of high current IGBTs. The IX2204 provides two high current outputs capable of sourcing 2A and sinking 4A. The outputs can be paralleled for IGBT gates that require higher drive current. The outputs have a wide operating voltage range, and are able to provide a negative gate drive voltage to ensure the turn-off of high power IGBTs. A desaturation detection circuit protects the power IGBT during a short circuit. The IX2204 has a programmable two-level turn-off feature that protects the device against excessive voltages when the IGBT is being turned off due to an over-current situation. The IX2204 has under voltage lockout circuitry, a fault status output, and is available in a 16-lead thermally enhanced SOIC package. Features: IX2204 Functional Block Diagram A Channel Level Shift INB MODE TRISTATE DESAT 1.4V GND OUTHB Applications: OUTHA OUTLA Control Logic BLANK FAULT VLA VHB VHA UVLO INA • High Output Current: 2A Source / 4A Sink • Wide Operating Voltage Range: -10V to +26V • Negative Gate Drive Capability • Desaturation Detection Circuit • Separate Source and Sink Outputs • Programmable Blanking and Output Tristate • TTL Compatible Inputs • -40ºC to +125ºC Extended Operating Temperature Range • Under-Voltage Lockout Circuitry • Fault Status Output B Channel Level Shift OUTLB • Efficient IGBT Switching • Motor Controls • Switch Mode Power Supplies VLB For data sheets, go to www.ixysic.com/Products/ProdList.htm 22 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com NEW ! • IX3120 2.5A Output Current Optically Coupled Gate Driver The IX3120 Gate Driver includes an input infrared LED that is optically coupled to a power output stage. The power output stage is capable of sourcing or sinking 2.5A of peak current, which is ideal for driving IGBTs and MOSFETs in the mid-power range. The gate driver optocoupler with its low input LED current, high output peak current, and high noise immunity (25kV/s) is ideally suited for use in motor control and inverter applications. The IX3120 is provided in an 8-pin DIP package and an 8-pin surface mount package. Features: IX3120 • 2.5A Maximum Peak Output Current • 25kV/µs Minimum Common Mode Rejection (CMR) at 1500VCM • Wide Operating Voltage Range: 15V to 30V • Undervoltage Lockout with Hysteresis • 3750Vrms Input to Output Isolation • Wide Temperature Range: -40°C to +100°C N/C 1 8 VCC ANODE 2 7 VO CATHODE 3 6 VO N/C 4 5 VEE Applications: • Isolated IGBT / MOSFET Gate Drive • Switch Mode Power Supplies • Industrial Inverters • Motor Drivers • IX3180 2.5A Output Current High Speed Gate Driver Optocoupler The IX3180 is a high speed MOSFET gate drive optocoupler. It consists of an input infrared LED that is optically coupled to an integrated power gate driver that is capable of sourcing and sinking 2.5A of peak current. The IX3180 is ideally suited for high frequency driving of power MOSFETs used in high performance, DC/DC converters, motor control inverter applications, and high performance switching power supplies. The IX3180 is available in an 8-pin DIP package and an 8-pin surface mount package. IX3180 Features: • 2.5A Maximum Peak Output Current • 200ns Maximum Propagation Delay Over Temperature Range • 20ns Typical Pulse Width Distortion • 10kV/µs Minimum Common Mode Rejection (CMR) at 1500VCM • Wide Operating Voltage Range: 10V to 20V • Undervoltage Lockout with Hysteresis • 3750Vrms Input to Output Isolation • Wide Temperature Range: -40°C to +100°C N/C 1 8 VCC ANODE 2 7 VO CATHODE 3 6 VO N/C 4 5 VEE NEW ! Applications: • Isolated Power MOSFET Gate Drive • Switch Mode Power Supplies • Industrial Inverters • Motor Drivers For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 23 • Optically Isolated Gate Drivers The CPC1580 and CPC1590 are high speed, optically isolated Gate Driver ICs. On-chip circuitry charges an external capacitor from the load voltage which eliminates the need for an external IC power supply. These Gate Drivers are ideal for low duty cycle switching applications. Both devices are provided in an 8-pin flatpack package. 8-Pin Flatpack CPC1590 8 1 4 VCAP NC CST 7 LOAD VD NC +VLOAD 5 2 VIN VG 3 Q1 6 Input Control Current (mA) 2.5 2.5 CPC1580 CPC1590 • No External IC Power Supply • Low Drive Power Requirements (TTL/CMOS Compatible) • Load Voltages up to 200V • Fast Switching Times - On: 40sec / Off: 400sec Applications: -VLOAD VS Part Number Features: Gate Voltage @ IF=5mA (VG) 7.5 - 12 7.5 - 12 • Instrumentation • Medical Equipment (Patient / Equipment Isolation) • Multiplexers • Security • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Aerospace • Industrial Controls Blocking Voltage (VP) 65 200 Regulated Capacitor Voltage (VCAP-MAX) VDS - 0.2V 16 Switching Speeds ton / toff (s) 40 / 400 40 / 400 Isolation Voltage (Vrms) 3750 3750 • Optically Isolated Dual MOSFET Gate Drivers These Dual Optically Isolated Photodiode Arrays, which can produce an open-circuit voltage of up to 12V, are well suited for use in discrete solid state relay designs. The FDA215 and the FDA217 are provided in either an 8-pin DIP package or in an 8-pin surface-mount package. 8-Pin DIP Features: Input PV Output • Isolated 5.5V to 12V Photovoltaic Output • Floating Outputs for Parallel or Series Configuration 8-Pin Surface Mount Applications: Input Part Number FDA215 FDA217 PV Input Control Current (mA) 5 5 Output • MOSFET Driver • Isolated Floating Power Source Nominal Open-Circuit Voltage VOC (V) 5.5 11.75 Nominal Short-Circuit Current ISC (A) 2.5 4.5 Switching Speeds ton / toff (ms) 5/5 2 / 0.5 Isolation Voltage (Vrms) 3750 3750 For data sheets, go to www.ixysic.com/Products/ProdList.htm 24 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com Package Type 8-Pin DIP, 8-Pin Surface Mount 8-Pin DIP, 8-Pin Surface Mount HIGH VOLTAGE PRODUCTS • High Voltage Analog Switch Arrays Our High Voltage Analog Switches are low charge injection 8-channel & 16-channel, high voltage analog switch ICs for use in applications requiring high voltage switching. Control of the high voltage switching is via low voltage, TTL logic level compatible inputs for direct connectivity to the system controller. Switch manipulation is managed by serial to parallel shift registers whose outputs are buffered and stored by a transparent latch. Level shifters buffer the latch outputs, and operate the high voltage switches. Construction of the switches using reliable BCDMOS process technology on SOI (Silicon On Insulator) enables the switches to be organized as solid state switches with direct gate drive. Applications: Features: • Flexible High Voltage Supplies up to VPP - VNN=200V • Output Switch On Resistance Typically 20 • Low Charge Injection, Low Capacitance Analog Switches • Very Low Quiescent Current: 30nA Typical • -58dB Off-Isolation at 5MHz • Internal Bleed Resistors: CPC7232 & CPC7701 Part Number Number of Channels Channel On Resistance () Bleed Resistors (k) Clock Frequency (MHz) Turn-On Time (s) Turn-Off Time (s) Package Type CPC7220 8 20 - 5 5 5 50, 51 CPC7232 CPC7601 CPC7701 8 16 16 21 25 25 20 - 50 20 - 50 5 8 8 5 5 5 5 5 5 50, 51 50 50 CPC7220 8-BIT SHIFT REGISTER DIN DOUT LATCHES LEVEL SHIFTERS SWITCHES SW0 DIN DOUT D LE CL SW0 D LE CL L2 D LE CL SW2 L4 D LE CL CLK D LE CL SW5 D LE CL L6 D LE CL SW4 SW6 L7 D LE CL D LE CL SW7 VNN SWITCHES LEVEL SHIFTERS VPP OUTPUT SWITCHES DOUT D LE CL SW0 D LE CL SW1 D LE CL SW2 D LE CL SW3 D LE CL SW4 D LE CL SW5 D LE CL SW6 D LE CL SW15 SW1 L2 D LE CL SW2 CLK SW3 SW4 L5 D LE CL SW5 L6 D LE CL SW6 L15 D LE CL SW6 LATCHES DIN SW0 SW5 D LE CL LE L0 D LE CL L4 D LE CL SW3 CPC7701 16-BIT SHIFT REGISTER VPP L3 D LE CL SW2 D LE CL SW4 L5 D LE CL SW1 CLK SW3 LATCHES LEVEL SHIFTERS L1 D LE CL SW1 L3 D LE CL CL DOUT 28-Pin PLCC CPC7601 16-BIT SHIFT REGISTER OUTPUT SWITCHES DIN L0 D LE CL L1 D LE CL CLK LATCHES VPP LEVEL SHIFTERS VPP 48-Pin LQFP 50 51 CPC7232 8-BIT SHIFT REGISTER • Piezoelectric Transducer Drivers • Ultrasound Imaging • Printers • Industrial Controls and Measurement SW15 VNN CL LE D LE CL 8 Switches SW7 CL LE VNN RGND 16 Switches CL LE VNN RGND For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 25 • High Voltage Isolated Analog Switches 20-Pin SOIC CPC7514 Quad High Voltage Isolated Analog Switch Array ply! p u VS The CPC7514 Quad High Voltage (HV) Isolated Analog Switch Array builds upon our Line Card Access Switch (LCAS) design and fabrication expertise for telecom and non-telecom applications. This monolithic solid state device provides the switching functionality of four normally open (1-Form-A) relays in one small economical package. Designed to provide flexible single-ended or differential access to high voltage networks, the CPC7514 High Voltage Array (HVA) is configured as two sets of matched, paired switches for improved differential performance. Additionally, sensitive differential applications will benefit from the matched pairs excellent pair-to-pair isolation. The self-biasing switches do not require external high voltage supplies for proper operation. Independent switch current limiting and switch-pair thermal shutdown features provide enhanced protection for devices connected to high voltage networks up to +320V. 3.3 CPC7514 VDD = 3.3V S1* Features: Applications: S1A • Low, Matched RON • Switch Voltage up to ±320V • 320V Logic Input to Switch Output Isolation • 110dB Switch-to-Switch Isolation at 5kHz • Flexible Switch Configurations • Smart Logic for Power Up / Hot Plug State Control • 3.3V Operation with Very Low Power Consumption • Switch Current Limiting Protects Against Fault Conditions • Thermal Shutdown Protects Against Fault Conditions • Latched TTL Logic Level Inputs • Clean, Bounce-Free Switching • Monolithic IC Reliability • Instrumentation • Industrial Controls and Monitoring Automatic Test Equipment (ATE) Battery Charging Circuits • Telephony VoIP Gateways Central Office (CO) and Remote Terminal (RT) Concentrators PBX Systems Optical Network Terminals (ONT) Optical Network Units (ONU) Hybrid Fiber Coax (HFC) S2A S1B S2* Channel 1-2 S2B IN1 IN2 LATCH1 TSD1 L A T C H 1 Channel 1-2 Switch Control Logic S1 S2 * ±320V S3* S3A S4* Channel 3-4 S4A S3B S4B IN3 IN4 LATCH2 TSD2 L A T C H 2 Channel 3-4 Switch Control Logic S3 S4 CPC7512 Dual Shunt-Isolated High Voltage High Frequency Analog Switch This dual 1-Form-A high voltage, high frequency, isolated analog switch provides the switching functionality of two normally open (1-Form-A) solid state relays in one small economical package. Both switches incorporate a compensation method to minimize open-state capacitance for improved off-isolation over frequency. Designed to provide flexible single-ended or differential access to high voltage networks, the CPC7512 is configured as two independent switches with optimized state control. The self-biasing switches do not require external high voltage supplies for proper operation. An integrated thermal shutdown feature provides enhanced protection for devices connected to high voltage networks up to +320V, and an external signal to indicate the device is shut down. Applications: Features: CPC7512 S1A SW1B S1COM S1Sel0 S1Sel1 S1B SW1C L A T C H S1C Switch 1 Control Logic LATCH1 • Instrumentation • Industrial Controls and Monitoring • Low, Matched RON • Guaranteed Break-Before-Make (BBM) • Multiplexed Ultrasonic Transducer Switching • Automatic Test Equipment (ATE) • Switch Voltage up to 320V • Battery Monitoring and Charging • 60dB Off Isolation at 1MHz • Smart Logic for Power Up / Hot Plug State Control • 5V Operation with Very Low Power Consumption • Thermal Shutdown Protects Against Fault Conditions • Latched TTL Logic Level Inputs NEW ! TSD SW2A SW2B S2A S2B SW2C 20-Pin SOIC S2COM S2Sel0 S2Sel1 S2C L A T C H LATCH2 For data sheets, go to www.ixysic.com/Products/ProdList.htm 26 SW1A IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com Switch 2 Control Logic HIGH SPEED DIGITAL OPTICAL ISOLATORS NEW ! • CPC5001 Single-Channel, Each Direction Digital Optical Isolator The CPC5001 is a non-inverting digital optical isolator with buffered-logic inputs and open-drain outputs. Channel1 propagates a signal from SideA to SideB, while Channel2 sends a signal from SideB to SideA. It provides galvanic isolation across voltage differences up to 3750Vrms. When the two sides are powered by different supply voltages, it also functions as a logic level translator for levels as low as 2.7V or as high as 5.5V. Available in an 8-pin DIP or 8-pin surface mount package, it functionally replaces two logic buffers and two single-channel optoisolators. Internal bandgap references regulate the LED drive currents to 3mA to reduce peak power requirements. Unlike transformer or capacitive isolators, optical isolation passes DC signals, and does not need to be clocked periodically to refresh state. Buffered signals will always return to their proper value after a transient interruption at either side. Applications: CHANNEL1 CPC5001 1 INA1 VDDB 8 VDDA VDDB VDDB LED 2 GNDA 7 B VDDA B OUTB1 Features: A CHANNEL2 3 OUTA2 VDDB GNDB 5 INB2 B VDDA LED 4 VDDA 6 A A • Isolates One Signal in Each Direction • Operates From 2.7V to 5.5V • Buffered Inputs - No External LED Drive Required • Voltage Level Translation • Hysteresis at Inputs for Noise Rejection • Slew-Limited Drivers Reduce EMI • Power Down to Hi-Z Does Not Load Outputs • 5Mbd Data Rate • Isolated Signal Monitoring and Control • Power-Over-Ethernet • Power Supply High-Side Interface • Logic Level Translation • Microprocessor System Interface • Inter Integrated Circuit (I2C) Interface • Serial Peripheral Interface • Full Duplex Communication • Isolated Line Receiver • Isolated Data Acquisition Systems • CPC5002 Dual High Speed Digital Optical Isolator The CPC5002 is a high speed dual optical logic isolator with open-drain outputs. It galvanically isolates two open-drain logic signals across voltage differences up to 3750Vrms. Turning on the LED forces the output to turn on, which pulls the voltage at any external pullup resistor towards ground. Its high-gain CMOS comparator requires only 1.4mA of supply current, and only 1.5mA of LED drive current. Unlike transformer or capacitive isolators, optical isolation passes DC logic level signals, and does not need to be clocked periodically to refresh state. Buffered signals will always return to their proper value after a transient interruption at either side. Available in 8-pin DIP and surface mount packages. Features: Applications: • Dual Optics Isolates Two Signals • Operates Over 2.7V < VDD < 5.5V • 3750Vrms Galvanic Isolation • Power Down to Hi-Z Does Not Load Outputs • Low-Power CMOS Reduces Supply Current • LED Drive Current Only 1.5mA • High Speed: 10Mbaud Typical • Isolated Line Receiver • Ground Loop Elimination • ADC/DAC Digital Noise Isolation • 4-Wire I2C Bus Isolation 10 ANO1 1 CPC5002 8 LED 2 7 3 6 CAT1 CAT2 ! d u a Mb VDD OUT1 OUT2 LED 4 ANO2 5 GND For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 27 • CPC5902 Optically Isolated I2C Bus Repeater The CPC5902 is a dual, optically isolated, bidirectional logic bus repeater. It galvanically isolates two open-drain logic signals, and provides a galvanic isolation of 3750Vrms. When the two sides’ supply voltages are configured with different voltages, the CPC5902 also functions as a logic level translator for levels as low as 2.7V or as high as 5.5V. Unlike transformer or capacitive isolators, this optically isolated repeater passes logic level DC signals, and does not need to be clocked periodically to sustain logic states. Buffered signals will always return to their proper value after a transient interruption on either side. As a result, the CPC5902 does not generate the clocking or modulation signal interference that other types of bus repeaters can generate. Available in 8-pin DIP and surface mount packages. Features: Applications: • Bidirectionally Buffers Both I2C Signals • Extends and Isolates I2C Interfaces • Supports Standard and Fast Mode I2C (400kbps) • Supports I2C Clock Stretching • Operates on 2.7V to 5.5V 3750Vrms Optical Isolation VDDA IOA1 VDDB 1 A VDDA GNDA VDDB VDDB VDDB 8 B D Q CLR VDDB LED 2 A LED 7 IOB1 B A • Power-Over-Ethernet • I2C Bus Length Extender • Isolated Control and Signal Monitoring • Power Supply High-Side Interface • Supports DC Logic Level Buffering Without Refresh • Glitch-Free Operation • Power Down to Hi-Z Does Not Load I2C • Slew-Limited Drivers Reduce EMI ions s s i m RF E & EM mal lation i n i o RFI -M s I d k n e c l Clo h Voltag al EMI a a n r rn nte Hig Exte No I o t une m m I Optical Isolation Barrier CPC5902 VDDA IOA2 VDDA VDDA 3 6 A VDDA VDDA 4 VDDA LED VDDB VDDB B VDDA B D Q CLR SCL_B CPC5902 SDA_A SDA_B IOB2 I2C Master I2C Slave GNDA GNDB Visit our web site and download our Tech Brief, TB-101: “Optically Isolating an I2C Interface” For data sheets, go to www.ixysic.com/Products/ProdList.htm 28 VDDB VDDB VDDB SCL_A VDDB 5 LED B A GNDB IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com I2C Master I2C Slave • CPC5903 Optically Isolated I2C Bus Repeater The CPC5903 is a dual, optically isolated, logic bus repeater. It galvanically isolates two open-drain logic signals, and provides galvanic isolation across voltage differences up to 3750Vrms. When the two sides are powered by different supply voltages, it also functions as a logic level translator for levels as low as 2.7V or as high as 5.5V. It enables full bidirectional isolation of the I2C data signal and unidirectional isolation of the I2C clock signal. Unlike transformer or capacitive isolators, optical isolation passes DC logic level signals, and does not need to be clocked periodically to refresh state. Buffered signals will always return to their proper value after a transient interruption at either side. Available in 8-pin DIP and surface mount packages. Features: Applications: 2 • Bidirectionally Buffers SDA I C Signal • SideA Extends and Isolates I2C Interfaces • Standard-Mode and Fast-Mode I2C • SideB Fast-mode Compliant: VDDB > 4.5V • Operates on 2.7V to 5.5V • No Internal Clock - Low EM & RF Generation • Voltage Level Translation • Slew-Limited Drivers Reduce EMI • Power Down to Hi-Z Does Not Load I2C • 3750Vrms Galvanic Isolation CPC5903 VDDA • Isolated Signal Monitoring and Control • Power-Over-Ethernet • Power Supply High-Side Interface • I2C Bus Length Extenders • I2C Logic Level Translation IA VDDB VDDA 1 VDDB 8 B LED B VDDB GNDA 2 7 OB 6 GNDB A VDDB VDDA LED A 3 IOA VDDB D B Q CLR VDDA VDDB LED VDDA OPTOCOUPLERS 4 VDDA 5 B IOB A • Optically Isolated Linear Error Amplifiers Optically Isolated Linear Error Amplifiers combine our optical technology with an industry standard 431-type precision programmable shunt regulator to provide linear isolated feedback for power supply designs. The LIA120 features matched photodiodes for linear high-gain response with excellent temperature stability for a total gain error of less than 2dB. These devices are well suited for isolated high-gain feedback amplifiers that require excellent linearity and low temperature variation such as power supply feedback stages, modem and audio transformer replacements, industrial control signals, and sensor feedback. Features: Application: 8-Pin Surface Mount LIA120 • 70dB Linearity Typical • Power Supply Feedback • Optocoupler, Precision Reference, 8-Pin DIP and Error Amplifier in a Single Package • Low Voltage Operation: 2.7V Part Number LED LED (Input) Reference Voltage (V) VREF Tolerance (%) CTR K1 (%) CTR K2 (%) CTR Matching K3 (%) Linearity LIA120 1.24V 1 1-3 1-3 85 - 115 70 3750 8-Pin Surface Mount LIA130 1.24V 1 - - - - 3750 8-Pin DIP, 8-Pin Surface Mount (dB) LIA130 Isolation Voltage (Vrms) K COMP C FB A FB E COMP Package Type GND GND For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 29 • Single & Dual Optocouplers Single and Dual OptoMOS Optocouplers provide an optically isolated means of current detection or control of switching circuits. These devices offer a single or dual anti-parallel LED input stage for unidirectional or bidirectional signal control to the optically coupled output. The output can be either a single transistor or, for greater gain, a Darlington transistor. These optocouplers are ideal for use in circuits where electrical isolation of control circuitry or voltage detection is crucial. Features: Applications: • AC and DC Compatible Inputs • 1500Vrms, 3750Vrms, 5000Vrms I/O Isolation • Machine Insertable, Wave Solderable • Modem Switching (Laptops, Notebooks, PDAs) • Voltage Detection • TIP / RING Circuits Part Number Minimum Breakdown Voltage (BVCEO) 30 350 350 30 30 Typical Current Transfer Ratio (%) 330 5500 5500 1000 300 Maximum Saturation Voltage (V) 0.3 1.2 1.2 0.5 0.5 Input Control Current LDA101 LDA102 LDA110 LDA111 30 30 30 30 300 350 8500 8500 LDA200 30 LDA201 LDA202 LDA203 LDA210 LDA211 LDA212 LDA213 30 30 30 30 30 30 30 CPC1001N CPC1301 CPC1302 CPC1303 LDA100 4-Pin SOP 10 Package Type Configuration (mA) 0.2 1 1 0.2 1 Minimum Isolation Voltage (Vrms) 1500 5000 3750 5000 3750 10 42, 43 20, 22 42, 43 12, 14 A B I A E 0.5 0.5 1 1 1 1 1 1 3750 3750 3750 3750 12, 14 12, 14 12, 14 12, 14 C C F D 300 0.5 1 3750 20, 22 L 300 300 300 8500 8500 8500 8500 0.5 0.5 0.5 1 1 1 1 1 1 1 1 1 1 1 3750 3750 3750 3750 3750 3750 3750 20, 22 20, 22 20, 22 20, 22 20, 22 20, 22 20, 22 K H G N M J I 6-Pin Surface Mount 12 • Ringing Detection • Loop Detection • Current Sensing Configurations 8-Pin DIP 6-Pin DIP 8-Pin Surface Mount 14 20 • Telecom Switching A B C D E F G H I J K L M N 4-Pin DIP 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm 30 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 42 4-Pin Surface Mount 43 • Linear Optocouplers OptoMOS Linear Optocouplers feature an infrared LED optically coupled to a pair of photodiodes. The input photodiode is used to generate a feedback signal that provides a servomechanism to the LED drive current thus compensating for the LED’s nonlinear characteristics. The output photodiode provides an isolated output signal that is linear with respect to the servo LED current. Features: Applications: • Couples Analog & Digital Signals • 3750Vrms Input / Output Isolation • Bandwidth >200kHz in Photoconductive Mode • Bandwidth 40kHz in Photovoltaic Mode • High Gain Stability • Low Input / Output Capacitance • Low Power Consumption • 0.01% Servo Linearity • THD 87dB Typical • Machine Insertable, Wave Solderable 16-Pin SOIC • Power Supply Feedback Voltage / Current • Medical Sensor Interfacing • Isolation of Process Control Transducers • Isolated 4-20mA Converters • Digital Telephone Isolation 4 8-Pin DIP 20 Part Number Servo Gain K1=I1/IF (Min / Max) Forward Gain K2=I2/IF (Min / Max) Transfer Gain K3=K2/K1 (Min / Max) Input Control Current (mA) Isolation Voltage (Vrms) Package Type LOC110 0.004 / 0.03 0.004 / 0.03 0.668 / 1.179 2 - 10 3750 20, 21, 22 LOC111 LOC112 LOC117 LOC210 LOC211 0.008 / 0.03 0.004 / 0.03 0.008 / 0.03 0.004 / 0.03 0.008 / 0.03 0.006 / 0.03 0.004 / 0.03 0.006 / 0.03 0.004 / 0.03 0.006 / 0.03 0.733 / 1.072 0.733 / 1.072 0.887 / 1.072 0.773 / 1.072 0.773 / 1.072 2 - 10 2 - 10 2 - 10 2 - 10 2 - 10 3750 3750 3750 3750 3750 20, 21, 22 20, 21, 22 20, 21, 22 4 4 Two Fundamental Operating Configurations: Photoconductive Mode: • Wide Bandwidth (>200kHz) • 8-bit Linearity LOC11x LOC21x – LED – LED 8-Pin Flatpack + LED + LED C1 C2 C1 A1 A2 A1 21 C2 A2 – LED 8-Pin Surface Mount + LED C2 C1 A2 A1 22 Isolation Amplifier (Photovoltaic Mode) VCC VIN LOC110, LOC111 or LOC112 IF – + Photovoltaic Mode: • 14-bit Linearity • 40kHz Bandwidth I1 1 8 2 7 3 6 – 5 + I2 = K3I1 VOUT 4 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 31 DISCRETE COMPONENTS • N-Channel Depletion Mode FETs SOT-89 Our N-channel depletion mode Field Effect Transistors (FETs) utilize a proprietary third generation vertical DMOS process. The third generation process realizes world class, high voltage MOSFET performance in an economical silicon gate process. The vertical DMOS process yields a robust device for low-power applications with high input impedance. These highly reliable FET devices have been used extensively in our solid state relays for industrial and telecommunications applications. These normally on MOSFETs are well suited for low cost, pre-regulator applications that are tolerant of high voltage drop and power dissipation between the power source and the output regulator stage. Part Number CPC3701 CPC3703 CPC3708 CPC3710 CPC3714 CPC3720 CPC3730 CPC3902 CPC3909 CPC3960 CPC3980 CPC3982 CPC5602 CPC5603 V(BR)DSX (V) 60 250 350 250 350 350 350 250 400 600 800 800 350 415 RDS(on) Max () 1 4 14 10 14 22 30 2.5 9 44 45 380 14 14 VGS(off) Min (V) -0.8 -1.6 -2 -1.6 -1.6 -1.6 -1.6 -1.4 -0.9 -1.4 -1.4 -1.4 -2 -2 VGS(off) Max (V) -2.9 -3.9 -3.6 -3.9 -3.9 -3.9 -3.9 -3.1 -3.1 -3.1 -3.1 -3.1 -3.6 -3.6 IDSS @ VGS = 0V Min (mA) 600 360 220 240 130 140 400 300 100 100 20 - ID @ VGS = -0.57V Min (mA) 130 130 130 SOT-223 Package Type Features & Comments SOT-89 SOT-89 SOT-89, SOT-223 SOT-89 SOT-89 SOT-89 SOT-89 SOT-223 SOT-89, SOT-223 SOT-223 SOT-223 SOT-23 SOT-223 SOT-223 NEW ! Designed for Use with LITELINK Designs Designed for Use with LITELINK Designs • Diode Bridges The CPC7556N integrated diode bridge offers protection from high voltage transients by means of an adjustable voltage clamp. The clamp performs two actions, first to limit the voltage across the diode bridge rectified outputs to a value determined by external resistors and the gate voltage, and second to fully discharge the V+ to V− outputs when the gate’s trigger threshold is exceeded during the voltage limiting function. The rectified outputs are discharged as a result of the voltage fold-back function of the OVP device. Voltage fold-back of the OVP circuit will continue until the current through the protector falls below the hold current threshold. The CPC7557N is an integrated diode bridge built on our High Voltage SOI technology. Very small in size, this integrated diode bridge device offers a space-saving method for inclusion of a highly reliable, monolithic, full-wave bridge rectifier into today’s miniature circuit designs. 8-Pin SOIC Features: Applications: • Monolithic Construction • Surface Mount Package • Telecommunications Protection Clamp • High Voltage Multiplexer / Switch • High Voltage ESD Clamp Part Number CPC7556 CPC7557 Reverse Voltage (V) 100 100 Forward Current (mArms) 240 240 A/B A B/A Diode VF Drop (V) 0.97 0.97 Thyristor Current (mA) 120 - K G A/B Reverse Leakage ILEAK (A) 1 1 + CPC7557 For data sheets, go to www.ixysic.com/Products/ProdList.htm 32 + CPC7556 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com B/A - DISPLAY PRODUCTS • High Voltage LED Drivers IX9908 High Voltage, Dimmable LED Driver with PFC Control The IX9908 is a quasi-resonant controller optimized for phase-cut dimmable, off-line LED applications. Precise PWM generation supports phase-cut dimming and power factor correction. The product features a wide operating range, up to 600V, and low power consumption. Multiple safety features ensure full system protection in failure situations. The IX9908, with its strong feature set and low cost, is an excellent choice for quasi-resonant flyback LED bulb designs. IX9908 Typical Application COUT CZCV CVCC + - Aux NEW • Single Stage, Primary Control with PFC and Dimming Features • >90% Efficiency • >98% Power Factor • Wide Operating Voltage Range: Up to 600V 8-Pin SOIC • Digital Soft Start • Cycle-by-Cycle Peak Current Control DOUT SNUBBER RZCV1 AC Features: T1 DVCC CIN ! RZCV2 VCC Q1 ZCV HV GD LEDs IX9908 RIN1 RIN2 GND CS VR CC RCS DVR CVR CPC9909 High Efficiency, High Brightness Off-Line LED Driver The CPC9909 is a low-cost, high-efficiency, off-line, high-brightness (HB) LED Driver manufactured using our high voltage BCDMOS on SOI process. It has an internal regulator that allows it to operate from 8VDC to 550VDC. Available in an 8-pin SOIC and a thermally enhanced 8-pin Power SOIC. The wide input operating voltage range enables the driver to be used in a broad range of HB LED applications. CPC9909 VDD Voltage Regulator VIN RT RT 8-Pin SOIC Voltage Reference Features: • 8V to 550V Input Voltage Range • >90% Efficiency • Stable Operation at >50% Duty Cycle • Drives Multiple LEDs in Series / Parallel • Regulated LED Current • Linear or PWM Brightness Control Inputs • Resistor-Programmable Minimum Off-Time • Buck or Boost Configuration + 250 mV Q S Minimum Off Time One Shot TRIG Q GATE R 8-Pin Power SOIC LD + CS PWMD GND For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 33 MXHV9910 High Voltage, Off-Line LED Driver The MXHV9910 features a fixed-frequency, peak-current control method, which provides an ideal solution for driving multiple LEDs in series and in parallel. Internal circuitry allows it to operate from a universal AC line, or from 8VDC to 450VDC. This highly versatile input operating voltage enables this IC to be used in a broad range of HB LED applications. In addition, LED dimming can be implemented by applying a small DC voltage to the LD pin, or by applying a low-frequency digital PWM signal to the PWMD pin. Applications include flat-panel display RGB backlighting, signage, decorative LED lighting, and DC & AC/DC LED driver applications. Available in an 8-pin SOIC and a thermally enhanced 8-pin Power SOIC. 8-Pin Power SOIC VDD MXHV9910 VIN Voltage Regulator Voltage Reference 250mV RT OSC Features: 8-Pin SOIC • 8V to 450V Input Voltage Range • >90% Efficiency • Drives Multiple LEDs in Series / Parallel Combinations • Regulated LED Drive Current • Linear or PWM Brightness Control Inputs • Resistor-Programmable Oscillator Frequency - PWM Control + LD GATE + PWMD GND CS • ePaper Gate & Source Drivers IXEP1400 400-Channel ePaper Source Driver IXEP1400 The IXEP1400 is a 400-channel e-Paper source driver. The IXEP1400 features a 400-bit long, 2-bit wide serial-input parallel-output digital shift register with a level conversion on each parallel output. This converts the 2 digital bits into either VPOS, VSS, or VNEG analog output voltages. An 8-bit input bus simultaneously inputs 4 groups of 2 bits each. The IXEP1400 is designed to operate over a temperature range of -40°C to +85°C, and is available as Gold Bumped Die in Wafer Form or Waffle Pack. Features: Applications: • +/-15 Volt Output Driver Supply Voltage • Drives Segment or Active Matrix Displays • 3-Level Gray Scale • 50MHz Clock Frequency • Bidirectional Data Transfer • 2.7V to 5.5V Logic Supply Voltage • Cascadable • eBooks / eReaders • Electronic Shelf Labels / Point Of Purchase Displays • Mobile Phones / Portable Handheld Devices • Smart Cards • Signage OUT1 VPOS VSS2 VNEG OUT399 OUT400 LEVEL SHIFTER/DRIVER DECODE OE LATCH LE 4-way Interleaved 2-bit Register Stages NEW ! 4x(1-100) Data path when SHR=1 D(7_0) VDD VSS Data path when SHR=0 CONTROL LOGIC Clock Direction SHR CE CL RST IXEP2300 300-Output ePaper Gate Driver IXEP2300 The IXEP2300 is a 300-channel, 42V display gate driver. It has an internal pattern generator for applications where minimal controller interface is desirable. It also has global blanking and inversion to facilitate powering up and down the display in the inactive state. The IXEP2300 features token passing capability and a sleep mode to reduce power consumption. IXEP2300 is available as gold-bumped die in wafer form and in a waffle pack. Features: Applications: • 300 Output Gate Driver • 42V HV Output Drive Capable (VDD to VEE) • 3.3V Logic Operation • Internal Pattern Generator • Reset, Blanking, Polarity Inversion • Bypass Function • Cascadable With Bidirectional Shift Control • eBooks / eReaders • Electronic Shelf Labels / Point Of Purchase Displays • Mobile Phones / Portable Handheld Devices • Smart Cards • Signage NEW 1 HV Out o[1:300] 300 Level Translators & Drivers INV/, BLANK/ HALF Data Inversion & Overwrite tknl Bidirectional Shift Registers ! CK, mode[1:2], DCR, UP, RST/, BYPASS For data sheets, go to www.ixysic.com/Products/ProdList.htm 34 OUT2 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com Pattern Generator & Control Bias Control tknr ON/ MXEI2240 240-Output ePaper Gate Driver MXEI2240 is a 240-bit serial shift register, level translator, and high voltage buffered driver. MXEI2240 is an excellent choice for driving the displays of eBooks and eReaders, mobile phones and other portable handheld devices, smart cards, and other electronic display devices. MXEI2240 output switching modes are: one pulse, continuous two pulse, jumping two pulse, or no pulse pattern. MXEI2240 can be cascaded up to a maximum of four devices. MXEI2240 is available as gold bumped die in wafer form and in a waffle pack. CE1 CE2 R/L SPV CKV Features: • CMOS Technology • Drives Segment or Active Matrix Displays • 16V to 57V Output Drive (VDD to VEE) • Selectable Output Shift Direction and Polarity LEVEL TRANSLATORS MXEI2240 WALK0 TEST1 MODE1 MODE2 SHIFT REGISTER / PULSE GENERATOR CONTROLLER VBIAS GENERATOR BIT1 BIT2 ... BIT240 LS/AMP LS/AMP ... LS/AMP BUFFER/ DRIVER BUFFER/ DRIVER ... VDD VDD BUFFER/ DRIVER VDD ESD DIODES MXEI1480 ±15V ePaper Source Driver VEE The MXEI1480 is a selectable 400-bit or 480-bit long, 2-bit wide, serial-input, parallel-output digital shift register with level conversion on each parallel output, which converts the 2 digital bits into VPOS, VSS, or VNEG analog output voltages. An 8-bit input bus simultaneously inputs 4 groups of 2 bits each. MXEI1480 is available as gold-bumped die in waffle pack, gold-bumped die in wafer form, 70mm Wide Tape Carrier, and 40mm wide chip-on-film (COF). Features: • CMOS Technology • ±15V Output Driver Supply Voltage • Drives Segment or Active Matrix Displays • 4-Level Gray Scale • 25MHz Clock Frequency • Bidirectional Data Transfer • Selectable Register Length • 2.7V to 5.5V Logic Supply Voltage • Cascadable VEE OG1 VPOS VSS VNEG OUT2 OUT479 OE DECODE LE LATCH CLOCK DIRECTION D(7...0) SHR MODE CE CL 4 x (1-100) 101-120 WHEN SHR = 0 MODE 400 480 CONTROL LOGIC MX860 ±15V ePaper Source Driver • CMOS Technology • ±15V Output Driver Supply Voltage • Drives Segment or Active Matrix Displays • 4-Level Gray Scale • 25MHz Clock Frequency • Bidirectional Data Transfer • Selectable Register Length • 2.7V to 5.5V Logic Supply Voltage • Cascadable OUT480 LEVEL SHIFTER / DRIVER DATA PATH WHEN SHR = 1 Features: OG240 MXEI1480 OUT1 4-WAY INTERLEAVED 2-BIT REGISTER STAGES The MX860 is a selectable 240-bit, 256-bit, or 268-bit long 2-bit wide serial-input, parallel-output digital shift register with level conversion on each parallel output, which converts the 2 digital bits into VPOS, VSS, or VNEG analog output voltages. An 8-bit input bus simultaneously inputs 4 groups of 2 bits each. MX860 is available as gold-bumped die in waffle pack, gold-bumped die in wafer form, and 48mm Super Wide Tape Carrier. VEE OG2 MX860 VPOS VSS VNEG OUT1 OUT2 OUT267 OUT268 LEVEL SHIFTER / DRIVER OE DECODE LE LATCH 4-WAY INTERLEAVED 2-BIT REGISTER STAGES DATA PATH WHEN SHR = 1 CLOCK DIRECTION D(7...0) SHR MODE1 MODE0 CE CL 4 x (1-60) 61-64 WHEN SHR = 0 MODE 240 256 65-67 268 CONTROL LOGIC For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 35 TELECOMMUNICATIONS PRODUCTS • Line Card Access Switches (LCAS) 28-Pin SOIC 8 32 16-Pin SOIC 34 20-Pin SOIC The LCAS product family consists of monolithic ICs that contain high voltage switches for TIP and RING line break, power ringing, line test access, test in access, and ringing generator testing. They provide the necessary functions to replace all 2-Form-C electromechanical relays found on both traditional voice and integrated voice and data (IVD) line cards found in Central Office, Digital Loop Carriers, and Channel Banks. LCAS ICs enable low-power, high-density line cards. New features include: (1) TTL compatible inputs, (2) smart logic for safe power up and hot plug state control, and (3) increased dV/dt immunity. Applications: Features: • PBX Systems • VoIP Gateways • Channel Banks • Pair Gain Systems • Central Offices (CO) • Fiber in the Loop (FITL) • Hybrid Fiber Coax (HFC) • Digital Loop Carriers (DLC) • Digitally Added Main Line (DAML) • Monolithic IC Reliability • Impulse Noise Reduction • Low, Matched On Resistance • Built-in Zero-Cross Switching • Small Surface Mount SOIC Packages • Ultra-Low Power Consumption of <10.5mW • Robust Power-Cross and Lightning Surge Performance • Current Limiting, Thermal Shutdown, and SLIC Protection 1 itch 5 0 0 V CP dV/d / s ! t C7 69x Imm Fa m u n i t i ly y Sw NEW ! LCAS Devices Switch Pairs Test Out Protection Features Part Number CPC7691BA CPC7691BB Minimum 1500V/s dV/dt • • # Switches 4 4 Break • • Ringing • • CPC7692BA CPC7692BB CPC7692BC • • • 6 6 6 • • • • • • • • • CPC7695xA CPC7695xB • • 10 10 • • • • • • • • CPC7695xC • 10 • • • • CPC7591BA CPC7591BB 4 4 • • • • CPC7592BC 6 • • CPC7594BA 6 • • Test In • • Ringing Test Zero-Cross Switching • • Current Limit • • Diode Bridge • • Protection SCR • Minimum Hold Current (mA) 110 Logic States 3 3 • • • • • • • • • • 110 • 110 4 4 5 32 32 32 • • • • • • • • • 110 7 7 8, 34 8, 34 • • • • • 110 8 8, 34 • • • • • • • 110 3 3 32 32 • • • • 110 5 32 • • • • 110 4 32 For data sheets, go to www.ixysic.com/Products/ProdList.htm 36 Package Type (Page 35) IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com 32 32 • CPC75282 Dual 6-Pole LCAS 44-Pin TQFP The CPC75282 Dual Line Card Access Switch (LCAS), a member of our next generation Line Card Access Switch family, is a monolithic solid state device that provides the switching functionality of four 2-Form-C relays in a single, small, economical package. The CPC75282 Dual LCAS device is designed to provide ringing and test access to the telephone loop in Central Office, Digitally Added Main Line, Private Branch Exchange, Digital Loop Carrier, and Hybrid Fiber Coax / Fiber in the Loop analog line card applications. Test access switches provide access to the telephone loop for line (drop) test or message waiting in the PBX application. Available in a 44-pin TQFP package. ½ CPC75282 VDD TTEST1 CHANNEL 1 of 2 TRINGING1 Features: Applications: • Improved Switch dV/dt Immunity of 1500V/µs • Smart Logic for Power Up / Hot Plug State Control • Low, Matched RON • Eliminates the Need for Zero-Cross Switching • Flexible Switch Timing to Transition from Ringing Mode to Talk Mode • Tertiary Protection Consisting of Integrated Current Limiting, Voltage Clamping, and Thermal Shutdown for SLIC Protection • 5V Operation with Very Low Power Consumption • Intelligent Battery Monitor • Latched Logic Level Inputs, No External Drive Circuitry Required • VoIP Gateways • Central Office (CO) • Digital Loop Carrier (DLC) • PBX Systems • Digitally Added Main Line (DAML) • Hybrid Fiber Coax (HFC) • Fiber in the Loop (FITL) • Pair Gain System • Channel Banks SW3 X X SW5 TLINE1 TBAT1 X SW1 BATTERY MONITOR SW2 RLINE1 RBAT1 X SW4 X SW6 X RRINGING1 CH1 RTEST1 SWITCH CONTROL LOGIC CH2 FGND1 VBAT P1 P2 P3 LATCH1 LATCH2 TSD1 TSD2 OFF1 OFF2 L A T C H DGND CFG • CPC7508 LCAS for Ringing SLIC The CPC7508 is a member of our next generation Line Card Access Switch (LCAS) family. Used with ringing SLICs, it provides the necessary functions to replace the two 2-Form-C electromechanical test relays used in contemporary Fiber to the Home (FTTH) and Optical Network Unit (ONU) deployments, as well as Voice over IP (VoIP) telephony terminals. Solid state switches provide the mechanism for TIP and RING line break, drop test, and channel test while requiring only a single +12V supply for operation. Interface compatibility with 3.3V or 5V logic for switch state control is provided by the TTL logic level inputs. The CPC7508 is designed for fiber access units where EMR’s are used for test access and line monitoring functions, but solid state switches are desired due to reduced operating noise, lower power consumption, and longer lifetimes. Available in a 16-pin SOIC package. Features: • TTL Logic Level Inputs for 3.3V Logic Interfaces • Smart Logic for Power Up / Hot Plug State Control • Monolithic IC Reliability • Low, Matched RON • Clean, Bounce-Free Switching • Tertiary Protection Consisting of Integrated Current Limiting and Thermal Shutdown for SLIC Protection TTEST_IN (TCHAN_TEST) CPC7508 +12VDC TTEST_OUT (TDROP_TEST) 1 VDD 8 7 X SW7 16-Pin SOIC Tip X SW3 TLINE 6 X SW5 5 TBAT X SW1 Secondary Protection Ring Applications: • Fiber to the Home (FTTH) • Fiber in the Loop (FITL) • VoIP Gateways • PBX Systems • Digitally Added Main Line (DAML) • Hybrid Fiber Coax (HFC) RLINE 11 Ringing SLIC SW2 X X SW4 12 RBAT X SW6 X RTEST_OUT (RDROP_TEST) 10 L A T C H Switch Control Logic SW8 9 2 GND 16 INA 15 INB 14 13 INC LATCH 3 TSD RTEST_IN (RCHAN_TEST) For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 37 • LITELINK™ Silicon DAA, Phone Line Interface The LITELINK Phone Line Interface is the industry’s only single-package silicon Data Access Arrangement (DAA) featuring a 32-pin, small outline, low profile, surface mount package. It is ideal for both voice and data (V.22bis to V.90/V.92) and applications in particularly dense circuit environments. The internal optical isolation barrier eliminates high-cost transformer or capacitive isolation circuits. This solution saves cost relative to competitive circuits through reduced passive component count and smaller printed circuit board space. The 3kVrms internal isolation barrier exceeds all worldwide regulatory requirements. In addition, the LITELINK application circuit is capable of surviving 6kV (10sec x 700sec) lightning surge waveforms making it the most robust silicon DAA on the market. LITELINK offers the lowest operational phone line quiescent current. The device easily interfaces to commonly available standard single-ended or differential voice and modem codecs on the market. Contact IXYS Integrated Circuits Division for information on codec reference designs that offer programmable AC termination impedance for global applications. LITELINK complies with international PSTN agency requirements. The newest device is the CPC5622 that offers continuous Caller-ID (CID) signal monitoring, which is ideal for telephony applications in countries where CID information is present before the ringing signal. The CPC5622 also offers both full-wave and half-wave ringing signal detection, enabling the designer to choose the appropriate interface to the codec/DSP block. Available in a 32-pin SOIC package. Features: • Voice and Data Applications • Modem DAA for Speeds up to V.92 • Half-Wave or Full-Wave Ringing Detection • Worldwide Telephone Network Compatibility • Caller-ID Reception • Line Side Powered from Telephone Line • 3.3V to 5V Power Supply • Easy Interface with Modem ICs and Voice Codecs • High Power Transmit Option for Voice Applications (>3dBm) • Small 32-Pin SOIC Package Part Number Isolation Voltage (Vrms) Power Supply (V) Caller ID Ringing Detect CPC5622 3000 3.3 - 5 Continuous Half-Wave & Full-Wave CPC5621 CPC5620 3000 3000 3.3 - 5 3.3 - 5 Selectable Selectable Full-Wave Half-Wave CPC5622 Isolation Barrier Tx+ Tx- Transmit Diff. Amplifier TIP Applications: • Computer Telephony • VoIP Gateways • PBXs • Satellite Set-Top Box • V.92 Modems • Fax Machines • Voice Mail Systems • Embedded Modems • Vending Machines • Automated Banking • Remote Metering • Surveillance • Security Systems Transmit Isolation Amplifier MODE 32-Pin SOIC TX Gain Trim OH RX Gain Trim Rx- Receive Diff. Amplifier RING Half Wave Rx+ RING2 Receive Isolation Amplifier RING RX MUX & Ringing Det. Full Wave CSNOOP RSNOOP Snoop Amplifier CSNOOP RSNOOP Ringing Detect Outputs For data sheets, go to www.ixysic.com/Products/ProdList.htm 38 Transconductance Stage 2-4 Wire Hybrid AC/DC Termination Hook Switch IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com • Voltage Monitor Devices The CPC5712 is a special-purpose Voltage Monitor with Detectors integrated circuit that is used in various high voltage telephony applications such as VoIP gateways and IP-PBXs, as well as non-telephony applications in instrumentation and industrial control. The device monitors the TIP/RING potential through a high-impedance divider (resistor isolation) to derive two resistor-programmable signal level detects, polarity information, and a scaled, linear representation of the phone line voltages. The CPC5710 is a versatile building block for designing telephone line-monitoring circuits. The device has two outputs: a scaled, linear representation of the input TIP/RING voltage, and a switchable, internally set comparator output. The comparator output provides a ringing detect signal, the level of which is set by the resistor values selected for the input network. A formula for selecting these input resistors is given in the CPC5710 Data Sheet that is available on our web site. The Data Sheet also includes an application circuit that derives Line-in-Use (LIU) and line polarity information from the scaled output signal. This high-impedance, resistive-barrier application circuit is fully compliant to the EN 60950 safety standard, and meets the ITU-T K.21 over voltage and over current specifications (with appropriate PCB layout). In use, the resistor divider and the high input impedance of both the CPC5710 and the CPC5712 make the circuits practically undetectable on the line. CPC5712 Features: CPC5710 Features: • Two Independent, Programmable Level Detectors with Programmable Hysteresis • Fixed-Level Polarity Detector with Hysteresis • Differential Linear Output • Excellent Common-Mode Rejection Ratio (CMRR) • 16-Pin SOP Package • Worldwide Telephone Network Compatibility • Minimum External Components • High Differential Input Impedance, Very Low Common-Mode Input Impedance • Fixed Gain 16-Pin SOP • 3V to 5.5V Operation • Low Power Consumption • CMOS Logic Level Output (TTL Compatible) • Differential or Single-Ended Linear Output • Full-Wave Ringing Level Detector Comparator with Internal Threshold, Large Hysteresis, and TTL Logic Level Output • High Common-Mode Rejection Ratio (CMRR) • 8-Pin SOIC Package • Worldwide Telephone Network Compatibility • High Differential Input Impedance, Very Low Common-Mode Input Impedance • Fixed Gain • 3V to 5.5V Operation 8-Pin SOIC • CMOS Logic Level Output (TTL Compatible) CPC5712 Applications: • VoIP Gateways, IP-PBX, xDSL • TIP/RING Monitoring: Polarity Detection for Caller ID, Enhanced 911, Line-in-Use, Battery Detection, PSTN Check • Non-Telephony Voltage Level Detection Applications: Instrumentation and Industrial Control V+ CPC5712 CPC5710 Applications: • Display Feature (Caller ID) Signal Buffering • Line-in-Use Detection (Another Phone-Off-Hook) • Ringing Signal Detection • Battery Presence Monitoring • TIP/RING Voltage Monitoring • Line Polarity CPC5710 1 VCC LIN/CMP RIN1 TIP OUT+ 5 7 IN+ 8 RIN2 IN- 3 - 1 + Analog Output G=5 DET1 3 DET2 2 VREF 15 14 VDD CMPOUT + OUT - 6 GND 2 - VDD 1.625V POLARITY 4 16 VDD 50kΩ + + RDIFF RING VDD VL1 9 VH1 10 Polarity Output IN+ IN- 6 12 + + AV=6 - - 7 Voltage Level Detect 2 13 R2 R3 R4 5 LINOUT+ 2V 4 LINOUT- VSS 8 + - R1 0V Switch shown in Detector Mode Voltage Level Detect 1 VH2 VL2 11 - Analog Output 1.25V R5 GND GND For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 39 • DC Termination ICs DC Termination IC: CPC1465 SHDSL/ISDN The CPC1465 provides a polarity-insensitive DC termination for wetting (sealing) current on the CPE side conforming to ITU-T G.991.2 to eliminate corrosion on G.SHDSL/ISDN lines. The CPC1465 has excellent linearity (70dB typ.) to minimize harmonic distortion, and well-controlled turn-on and turn-off characteristics to minimize injecting impulse noise with in-band signal energy into the G.SHDSL channel. This DC termination IC, which interfaces with the TIP/RING pair, is rated at 300V, and is able to handle power-cross and lightning transients with appropriate protection. Manufactured in our proven 320V Silicon-On-Insulator (SOI) process, the CPC1465 is packaged as a 16-pin SOIC or as a 16-pin DFN. Features: CPC1465 & Application Circuit • Meets Wetting (Sealing) Current Requirements Per ITU-T G.991.2 • Integrated Bridge Rectifier for Polarity Correction • Uses Inexpensive Optocoupler for DC Signaling 16-Pin DFN • Electronic Inductor, Breakover, and Latch Circuits • Current Limiting and Excess Power Protection Circuits • ANSI SHDSL and ISDN Compatible • MLT and SARTS Compatible • Excellent Linearity (70dB typ.) TIP 16-Pin SOIC Applications: RING 2.2k: 5% 4W • G.SHDSL • ISDN • Router and Bridge Customer Premises Equipment • Leased Line Equipment • T1/E1 Network Line Cards and Repeaters • Network Termination 1 (NT1) Equipment • Mechanized Loop Test (MLT) Networks • Switched Access Remote Test System (SARTS) Networks TC 16 NC 15 NC 14 RS 13 PD 12 NC NC 11 NC NC 10 1 PR+ 2 NC 3 NC 4 TIP 5 RING 6 7 8 PR- Electronic Inductor, Breakover, Latch, and Opto Driver Bridge Rectifier DC Blocking Capacitor 1mF 68: 1% 1/4W Transceiver Current Limit and Excess Power Protection COM 9 VCC 1 6 2 5 3 4 75k: Digital Control Circuitry DC Termination IC: CPC1466 Broadband ADSL/VDSL The CPC1466 is a DC Termination IC for broadband ADSL/VDSL applications. The high voltage, monolithic device provides a path for DC wetting (sealing) current in customer premises equipment (CPE) to eliminate phone line corrosion on DSL twisted-pair copper lines without telephone voice services (i.e. broadband-only services). Features: CPC1466 1 PR+ 2 NC 3 TIP 4 NC Electronic Inductor, Breakover, Latch, and Opto Driver Bridge Rectifier TC 16 NC 15 NC 14 RS 13 NC 12 5 NC 6 RING PD 11 7 NC NC 10 8 Current Limit and Excess PRPower Protection COM 9 16-Pin DFN 16-Pin SOIC • Meets Wetting (Sealing) Current Requirements Per ITU-T G.992.3 • Integrated Bridge Rectifier for Polarity Correction • Uses Inexpensive Optocoupler for DC Sealing Current Monitoring • Electronic Inductor, Breakover, and Latch Circuits • Current Limiting and Excess Power Protection Circuits • ADSL/VDSL Compatible with Low-Pass Filter Network • MLT and SARTS Compatible • Compatible with Portable Test Sets Applications: • ADSL/VDSL Broadband Modems • Router and Bridge Customer Premises Equipment • Leased Line Equipment • Mechanized Loop Test (MLT) Networks • Switched Access Remote Test Systems (SARTS) Networks For data sheets, go to www.ixysic.com/Products/ProdList.htm 40 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com • Telecom Multifunction Solid State Relays The OptoMOS line of Multifunction Products combines several optically isolated discrete component functions into a single package. These products mix and match solid state relays, optocouplers, bridge rectifiers, Darlington transistors, and Zener diodes to create highly functional circuits in a single, small package. Multifunction devices allow designers to consolidate circuit functions into a single device, freeing up valuable board space and reducing component count. Designed specifically for the telecommunications industry, the Integrated Telecom Circuit (ITC) series is well suited for voice telephony and modem applications, providing most of the major functions required when designing DAA (Data Access Arrangement) or voice (FXO) line interface circuits. Available in a 16-pin SOIC package. Features: Zener Protection Unidirectional Opto-Input No Zener Protection Bidirectional Opto-Input (1-Form-A) • 3750Vrms Input to Output Isolation • Multiple Functionality in a Single Package • Current Limiting (Part Numbers with “L” Suffix) • Machine Insertable, Wave Solderable • TTL and CMOS Compatible Zener Protection Bidirectional Opto-Input (1-Form-A) (1-Form-A) 16-Pin SOIC PV PV PV Applications: ITC117(L) ITC135 ITC137 Relay Parameters Part Number ITC117 ITC117L ITC135 ITC137 Blocking Voltage (VP) 350 350 350 350 Load Current (mA) 120 120 120 120 On Resistance () 15 20 15 15 • Telecommunication / Datacommunication • Instrumentation • I/O Subsystems • Electronic Switching • Medical Equipment (Patient / Equipment Isolation) • Security • Aerospace • Industrial Controls Optocoupler Parameters Input Control Current (mA) 5 5 5 5 Breakdown Voltage (V) 20 20 20 20 Current Transfer Ratio (%) 33 33 33 33 Saturation Voltage (V) 0.5 0.5 0.5 0.5 Input Control Current (mA) 6 6 6 6 Isolation Voltage (Vrms) 3750 3750 3750 3750 Package Type Features Full-Wave Ringing Detect Full-Wave Ringing Detect, Current Limiting Half-Wave Ringing Detect Full-Wave Ringing Detect 16-Pin SOIC 16-Pin SOIC 16-Pin SOIC 16-Pin SOIC • M-949-11 Line Sense Relay M-949-11 Balanced Dual Coil Telephone Line Current Sensing Relay • Senses Telephone Line Current From 15mA to 200mA • Used by Control Circuitry for: On-Hook / Off-Hook Monitoring Switch Hook Flash Detection Rotary Dial Pulse • Meets High Isolation Voltage Requirement of 4000V • Meets UL and British Standard Specifications • Includes 1-Form-A Relay Contact CO PBX Switching Equipment M-949 Tip 2 + Ring 3 - - 1 + + 4 6 - 5 LC Note: These relays are not polarity sensitive. The Positive and Negative indicators show the series-aiding coil configuration. Other Circuit (Dial Pulse Counter) DATA Strobe Off-hook For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 41 • Cybergate™ Data Access Arrangement (DAA) Modules The Cybergate family is a turnkey modular DAA solution. The V.34 family provides the circuitry required in a single, completely functional DAA circuit in a 1.07” x 1.07” x 0.4” plastic module. This plug-and-play design allows the user to choose the necessary options to minimize costs and maximize value. Standard features include surge protection, transient protection Zeners, ringing detection, hook switch circuitry, gyrator circuitry (impedance balancing), and a transformer. Caller-ID (CID) and loop current detection are also available as options. Part Number Features: Applications: • 28.8kbps • Optional Caller ID and Loop Current Sense • Ringing Detection • Low Power Hook Switch • Surge Protection • Gyrator Circuitry • Meets Most Regulatory Agency Requirements • Modems • Remote Data Acquisition • Fax Machines • Security / Metering • Computer Telephony • PBX • Voice Mail Systems Region Hook Switch Resistance DC Loop Current Return Loss (Min) () (mA) (dB) 15 20-120 18 15 20-120 18 15 20-120 18 35 5-120 14 CYG2100 N. America Asia N. America Asia N. America Asia European Union Except France & Spain CYG2110 France 35 5-120 14 CYG2111 CTR-21 35 5-60 14 CYG2217 15 20-120 39 CYG2218 N. America Asia N. America Asia 15 20-120 39 CYG2320 Australia - 5-120 14 CYG2000 CYG2011 CYG2020 Small Package Size! 1.07" x 1.07" x 0.4" 27.18mm x 27.18mm x 10.16mm Insertion Loss (Max) Ringing Voltage Detection Range Isolation Voltage TX - Transmit (dB) RX - Receive (dB) (Vrms) (Vrms) 20-150 1000 20-150 1000 20-150 1000 • 20-150 1500 • 29-150 1500 • 29-150 1500 • 20-150 1000 • • 20-150 1000 • • 29 MIN 1500 • TX 7 RX 7 TX 7 RX 7 TX 7 RX 7 TX 7 RX 7 TX 7 RX 7 TX 7.5 RX 7.5 TX1 RX 1 TX 1 RX 1 TX 7 RX 7 FEATURES Ringing Detection Full Wave Half Wave Loop Current Detect 2-4 Wire Conversion • • For data sheets, go to www.ixysic.com/Products/ProdList.htm 42 Caller ID IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com • • • M-980-02 Call Progress Tone Detector This Call Progress device is an inexpensive band detector that provides an accurate method of detecting common call progress tones including busy tone, dial tone, call waiting tones, and others. The detector is available in both DIP and SOIC packages, and operates on a 3V to 5V supply. Features: Applications: • Receive Common Call Progress Tones • The M-980-02 Operates with a Single 3-5 Volt Supply • Linear Input (Detector) • Inexpensive Band Detector with Wide Dynamic Range (>38dB) • Low Power Consumption • PBX Circuits • Billing Systems • Test Equipment • Point-of-Sale Terminals M-980-02: Call Progress Tone Detector VSS V REF VDD Ref Gen 16-Pin SOIC Bandpass Filter SIGIN Part Number M-980-02 Function (315 - 640Hz) Tone Detector Package Types 8-Pin DIP Level Sense Osc Digital Control Detect Clock Gen 16-Pin SOIC, 8-Pin DIP XIN XOUT Enable • M-986-2R2 MFC Transceiver The M-986-2R2 two-channel MFC Transceiver contains all the logic necessary to transmit and receive CCITT R2F (forward) and R2B (backward) multifrequency signals on one small 40-pin DIP IC or one 44-pin PLCC device. Operating with a 20.48 MHz crystal, the M-986 is capable of providing a direct digital interface to an A-law encoded PCM digital input. Each channel can also be connected to an analog source with the addition of a coder-decoder (codec) in the circuit. Features: M-986-2R2 Block Diagram • Direct A-Law PCM digital input • 2.048 Mb/s clocking • Programmable forward/backward mode • Programmable compelled/direct control • Operates with standard codecs for analog interfacing • Microprocessor read/write interface • Binary or 2-of-6 data formats • 5V power Applications: • Test equipment • Trunk adapters • Paging terminals • Traffic recorders • PBXs 40-Pin DIP 44-Pin PLCC For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 43 • CPC2400E Embedded Modem Module The Embedded Modem Module (EMM) combines a datapump and microcontroller with the Data Access Arrangement (DAA) to deliver an all-in-one solution for V.22bis modem transaction-oriented applications. This plug-and-play module provides a total solution complete with transferable FCC registration. It supports a standard serial V.24 TTL interface to the DTE equipment. The CPC2400E features a quick handshake time of 1.6 seconds. This offers a clear advantage for short connection sessions when compared to V.34 and V.90 modems which have a data handshake period greater than 10 seconds. Features: • Easy Integration and Installation • Small Footprint of 1.00” x 2.50” • Low Power Consumption • 5V Power Supply Operation • Supports V.22bis, V.22, V.23 • FCC Part 15B Compliant • FCC Part 68 User Transferable Registration • UL Approved CPC2400E +5V DTE Applications: CONTROLLER V.24 SERIAL • Point-Of-Sale (POS) • Gaming Equipment • Utility Metering • Lock Boxes • Remote Monitoring • Embedded Applications • Medical Appliances V.22BIS DATA PUMP TIP DAA RING AUDIO OUT GND For data sheets, go to www.ixysic.com/Products/ProdList.htm 44 LINE INTERFACE PARALLEL IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com OTHER SEMICONDUCTOR PRODUCTS • MX887D/P Hall-Effect Switches The MX887D and MX887P integrated Hall-Effect switches target the requirements of low-power portable devices with battery operating voltages from 2.5V to 5.5V. On-chip power management circuitry reduces the effective average current to just 5µA at 3V supply voltage. Both devices turn on when either a north or south magnetic pole is applied, and turn off when the magnetic field is removed. The MX887D switches between GND and high-impedance state, while the output of the MX887P switches between the supply voltage and GND. MX887D and MX887P are ideal reed relay replacements, especially in low-power portable device applications. Available in a TSOT-23 package. VSUPPLY Applications: VSUPPLY MX887D MX887P • Handheld Portable Devices • White Goods • Automotive - Body Systems • Security Systems • High-Reliability Reed Switch Replacement Ground Output Latch Hall Sensor Offset Cancellation Output Switch Power Management Logic Output Latch Switch Hall Sensor Offset Cancellation Power Management Logic Output Ground • Solar Cells Our Solar Cells address the diverse needs of the growing number of power solar applications. The SOI process, which also creates isolation trenches on the die, produces multiple solar cells on a single, monolithic piece of monocrystalline silicon. These isolated solar cells can then be interconnected to give a useful level of voltage from a small, SOIC package that can be easily installed in an automated process. Ideal for use in applications where high current is not needed, but where voltages higher than those provided by single solar cells is required. These solar cells are offered in 8-pin and 16-pin SOIC packages. Features: Part Number CPC1822 CPC1824 CPC1831 CPC1832 Open-Circuit Voltage (V) 4 4 8 8 Short-Circuit Current (A) 50 100 25 50 Package Type 8-Pin SOIC 16 Pin SOIC 8-Pin SOIC 16-Pin SOIC • Provides True Wireless Power • Triggers with Natural Sunlight or Artificial Light • Semiconductor Miniature Size and Reliability Applications: • Power Wireless Sensors • Solar Tracking • Portable Electronics • Solar Battery Chargers • Battery Operated Equipment • Consumer Electronics • Sunlight / Light / Flame Detection For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 45 • MX877 & MX879 Load Drivers These devices are 8-channel, high voltage switches with 8-bit parallel or serial input control. The 3-wire serial interface connects directly to a microprocessor using an industry standard protocol. These devices are designed to operate over a temperature range of -40°C to +85°C, and are available in a 28-pin QFN package. The MX877, with push-pull output configuration, can drive up to 60V at 80mA. Outputs can be paralleled for increased drive current up to a device total of 400mA sink or source. The MX879, with open-drain pullup output configuration, can drive up to 60V at 120mA. Outputs can be paralleled for increased drive current up to a device total of 600mA source. VCC CS SDO IN7 Features: Applications: • 6V to 60V Drive Supply Voltage • 2.7V to 5.5V Logic Supply Range • 3-Wire Serial Interface Plus Chip Select • Captures Serial and Parallel Input Data • Outputs can be Paralleled • Small 28-Pin QFN Package • White Goods • Automatic Test Equipment (ATE) • Industrial Equipment • Automotive Relay Control VPWR IN6 IN5 IN4 IN3 IN2 IN1 I/O Register Parallel Inputs Shift Direction Latch Register Driver Parallel In & Out Level Translator OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT0 IN0 28-Pin QFN SCK SDI OE GND • CPC5608 Low Power Transistor Array The CPC5608 is a 5-channel, low-power transistor array IC with a simple 2-state logic control input. A logic low input turns on switches OUT1, OUT2, and OUT3; a logic high turns on switches OUT4 and OUT5. Output transistors are capable of sinking 50mA in low output voltage (<7V) circuits. The IC features a low supply voltage range of 2.5V to 5.5V and no static supply bias current draw, making it ideal for portable battery and on-hook telephone applications. Available in an 8-pin SOIC package. CPC5608 8 VCC GND Features: Applications: • No Static Current Draw from Power Supply (CMOS Control) • Low-Voltage Operation (VCC = 2.5V) • Low Output Transistor Leakage • Portable Battery Equipment • Telephony • Instrumentation 3 7 6 INPUT 8-Pin SOIC OUT1 1 2 5 OUT2 OUT3 OUT4 4 OUT5 For data sheets, go to www.ixysic.com/Products/ProdList.htm 46 IXYS Integrated Circuits Division − 78 Cherry Hill Drive − Beverly, MA USA 01915 − www.ixysic.com • NCD2100 Non-Volatile Digital Programmable Capacitor The NCD2100 is an EEPROM-based digitally programmable variable capacitor that provides capacitive offset trimming for capacitance sensitive circuits. Programming the non-volatile EEPROM register value or implementing on demand capacitance value changes are easily accomplished by means of the simple two-wire serial bus. Providing 1024 discrete capacitance values over a nominal value range of 6.6pF to 37.553pF with very small step sizes, the NCD2100 is well suited to ensure proper operation of capacitive critical circuits. Additionally, to ensure interoperability over a broad array of design environments, the NCD2100 is rated for operation with supply voltages of 2.5V to 5.5V across the temperature range of -40ºC to +85ºC. Capacitance Range: 6.6pF to 37.553pF Features: • Very small capacitance step size • 1024 programmable capacitance values • Operating supply voltage: 2.5V to 5.5V • Operating temperature range: -40ºC to +85ºC • Device size: 2mm x 2mm (DFN-6), 2.9mm x 2.8mm (TSOT-6) NCD2100 VDD CDAC1 Applications: • VCXOs • Crystal Oscillators • Tunable RF Stages • RFID Tags • Industrial Wireless Control • Capacitor Sensor Trimming NEW X1 C0 ! PV DIGITAL INTERFACE CDAC2 TSOT Package: 2.8mm x 2.9mm DA CDAC3 DFN Package: 2mm x 2mm CLK VSS For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 − Customer Service +1 978 524 6768, +1 978 524 4900 47 Worldwide Sales Offices Americas Europe Asia World Headquarters IXYS Integrated Circuits Division 78 Cherry Hill Drive Beverly, MA USA 01915-1048 European Customer Service Centre IXYS CH GmbH Mattenstrasse 6A CH-2555 Brügg b. Biel, Bern Switzerland Asian Headquarters IXYS Taiwan Room N1016, Chia-Hsin, Bldg. II, 10F, No. 96, Sec. 2 Chung Shan North Road Taipei, Taiwan +1 978 524 6700 +1 978 524 4700 Toll-Free: 1 800 272 5273 +41 323 744 020 +41 323 744 029 E-mail: [email protected] Customer Service +886 2 2523 6368 +886 2 2523 6369 E-mail: [email protected] +1 978 524 6768 +1 978 524 4900 IXYS Integrated Circuits Division Copyright © December, 2014, IXYS Integrated Circuits Division Inc. All rights reserved.