PBA150 Dual Single-Pole OptoMOS® Relay INTEGRATED CIRCUITS DIVISION Parameter Blocking Voltage Load Current On-Resistance (max) Ratings 250 250 7 Units VP mArms / mADC Features • 3750Vrms Input/Output Isolation • Low Drive Power Requirements (TTL/CMOS Compatible) • High Reliability • Arc-Free With No Snubbing Circuits • FCC Compatible • VDE Compatible • No EMI/RFI Generation • Small 8-Pin Package • Machine Insertable, Wave Solderable • Surface Mount, Tape & Reel Versions Available Applications • Telecommunications • Telecom Switching • Tip/Ring Circuits • Modem Switching (Laptop, Notebook, Pocket Size) • Hook Switch • Dial Pulsing • Ground Start • Ringing Injection • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment-Patient/Equipment Isolation • Security • Aerospace • Industrial Controls Description PBA150 comprises two independent 250V, 250mA, 7 solid state relays: one single-pole, normally open (1-Form-A) relay and one single-pole, normally closed (1-Form-B) relay. Featuring low on-resistance, the PBA150 is designed to provide an ideal solution where a complementary Form-A/Form-B relay pair is required. Approvals • UL Recognized Component: File E76270 • CSA Certified Component: Certificate 1175739 • EN/IEC 60950-1 Certified Component: TUV Certificate B 09 07 49410 004 Ordering Information Part # PBA150 PBA150S PBA150STR Description 8-Lead DIP (50/Tube) 8-Lead Surface Mount (50/Tube) 8-Lead Surface Mount (1,000/Reel) Pin Configuration AC/DC Configuration + Control - Normally Closed - Control - Normally Closed + Control - Normally Open - Control - Normally Open 1 8 2 7 3 6 4 5 Normally Closed Pole Normally Open Pole Switching Characteristics of Normally Open Devices Form-A IF 90% 10% ILOAD ton toff Switching Characteristics of Normally Closed Devices Form-B IF ILOAD 90% 10% Pb DS-PBA150-R05 e3 toff www.ixysic.com ton 1 INTEGRATED CIRCUITS DIVISION PBA150 Absolute Maximum Ratings @ 25ºC Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 2 Ratings 250 5 50 1 150 800 3750 -40 to +85 -40 to +125 Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Units VP V mA A mW mW Vrms °C °C Derate linearly 1.33 mW / ºC Derate linearly 6.67 mW / ºC Electrical Characteristics @ 25ºC Parameter Output Characteristics Load Current 1 Continuous, AC/DC Configuration Peak On-Resistance Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics Input Control Current to Activate Input Control Current to Deactivate Input Voltage Drop Reverse Input Current Common Characteristics Capacitance, Input to Output 1 2 Conditions Symbol Min Typ Max Units 10ms IL=250mA VL=250VP IL ILPK RON ILEAK - - 250 ±500 7 1 mArms / mADC mAP VL=50V, f=1MHz ton toff COUT - 110 2.5 2.5 - IL=250mA IF=5mA VR=5V IF IF VF IR 0.4 0.9 - 0.7 1.2 - 5 1.4 10 mA mA V A - CI/O - 3 - pF IF=5mA, VL=10V A ms pF If both poles operate simultaneously, then the load current must be derated in order not to exceed the package power dissipation value. www.ixysic.com R05 INTEGRATED CIRCUITS DIVISION PBA150 Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating PBA150 / PBA150S MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time PBA150 / PBA150S 250ºC for 30 seconds Board Wash IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb R05 e3 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION PBA150 Mechanical Dimensions PBA150 2.540 ± 0.127 (0.100 ± 0.005) 9.652 ± 0.381 (0.380 ± 0.015) 8-0.800 DIA. (8-0.031 DIA.) 2.540 ± 0.127 (0.100 ± 0.005) 9.144 ± 0.508 (0.360 ± 0.020) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 PCB Hole Pattern 7.620 ± 0.254 (0.300 ± 0.010) 6.350 ± 0.127 (0.250 ± 0.005) 0.457 ± 0.076 (0.018 ± 0.003) 3.302 ± 0.051 (0.130 ± 0.002) 7.620 ± 0.127 (0.300 ± 0.005) 7.239 TYP. (0.285) 4.064 TYP (0.160) 0.254 ± 0.0127 (0.010 ± 0.0005) 7.620 ± 0.127 (0.300 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) PBA150S 9.652 ± 0.381 (0.380 ± 0.015) 2.540 ± 0.127 (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 0.635 ± 0.127 (0.025 ± 0.005) 3.302 ± 0.051 (0.130 ± 0.002) 9.525 ± 0.254 (0.375 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 ± 0.254 (0.300 ± 0.010) 0.254 ± 0.0127 (0.010 ± 0.0005) 0.65 (0.0255) 4.445 ± 0.127 (0.175 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) 4 www.ixysic.com R05 INTEGRATED CIRCUITS DIVISION PBA150 PBA150STR Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) K0 =4.90 (0.193) K1 =4.20 (0.165) Embossed Carrier Embossment W=16.00 (0.63) Bo=10.30 (0.406) Ao=10.30 (0.406) P=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice. 5 Specification: DS-PBA150-R05 ©Copyright 2012, IXYS Integrated Circuits Division OptoMOS® is a registered trademark of IXYS Integrated Circuits Division All rights reserved. Printed in USA. 12/22/2012