Data Sheet - Littelfuse

Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
MLA Automotive Varistor Series
RoHS
Description
The MLA Automotive Series of transient voltage surge
suppression devices is based on the Littelfuse Multilayer
fabrication technology. These components are designed
to suppress a variety of transient events, including those
specified in IEC 61000-4-2 or other standards used for
Electromagnetic Compliance (EMC). The MLA Automotive
Series is typically applied to protect integrated circuits and
other components at the circuit board level.
The wide operating voltage and energy range make the
MLA Automotive Series suitable for numerous applications
on power supply, control and signal lines.
The MLA Automotive Series is manufactured from
semiconducting ceramics, and is supplied in a leadless,
surface mount package. The MLA Automtove Series
is compatible with modern reflow and wave soldering
procedures.
Size Table
Metric
EIA
1608
0603
2012
0805
3216
1206
3225
1210
It can operate over a wider temperature range than Zener
diodes, and has a much smaller footprint than plastichoused components.
Features
Absolute Maximum Ratings
• For ratings of individual members of a series, see device ratings and specifications table.
MLA Auto
Series
Continuous
Units
Steady State Applied Voltage:
• AEC - Q200 compliant
• Halogen-Free and
RoHS compliant
• Leadless 0603, 0805,
1206 and 1210 chip sizes
DC Voltage Range (VM(DC))
3.5 to 48
V
AC Voltage Range (VM(AC)RMS)
2.5 to 40
V
Non-Repetitive Surge Current, 8/20µs
up to 500
Waveform, (ITM)
A
• -55°C to +125°C
operating temp. range
Non-Repetitive Surge Energy,
10/1000µs Waveform, (WTM)
J
• Operating voltage range
VM(DC) = 3.5V to 48V
Transient:
0.1 to 2.5
Operating Ambient Temperature Range (TA)
-55 to
+125
ºC
Storage Temperature Range (TSTG)
-55 to
+150
ºC
Temperature Coefficient (αV) of Clamping
Voltage (VC) at Specified Test Current
<0.01
%/º C
Additional Information
Datasheet
Resources
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15
Samples
• Multilayer ceramic
construction technology
•Rated for surge
current (8 x 20µs)
• Rated for energy
(10 x 1000µs)
•Inherent bi-directional
clamping
• No plastic or epoxy
packaging assures
better than UL94V-0
flammability rating
• Standard low
capacitance types
available
• Load Dump energy
rated per SAE
Specification J1113
Applications
• Suppression of
inductive switching
or other transient
events such as EFT
and surge voltage at
the circuit board level
• ESD protection for IEC
61000-4-2, MIL-STD883c method 3015.7,
and other industry
specifications
• Provides on-board
transient voltage
protection for ICS
and transistors
• Used to help achieve
electromagnetic
compliance of
end products
• Replaces larger surface
mount TVS Zeners in
many applications
Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
Device Ratings and Specifications
Maximum Ratings (125º C)
Part Number
Maximum
Continuous
Working
Voltage
VM(DC)
V3.5MLA0603NHAUTO
V3.5MLA0805NHAUTO
V3.5MLA0805LNHAUTO
V3.5MLA1206NHAUTO
V5.5MLA0603NHAUTO
V5.5MLA0805NHAUTO
V5.5MLA0805LNHAUTO
V5.5MLA1206NHAUTO
V9MLA0603NHAUTO
V9MLA0805LNHAUTO
V12MLA0805LNHAUTO
V14MLA0603NHAUTO
V14MLA0805NHAUTO
V14MLA0805LNHAUTO
V14MLA1206NHAUTO
V18MLA0603NHAUTO
V18MLA0805NHAUTO
V18MLA0805LNHAUTO
V18MLA1206NHAUTO
V18MLA1210NHAUTO
V26MLA0603NHAUTO
V26MLA0805NHAUTO
V26MLA0805LNHAUTO
V26MLA1206NHAUTO
V26MLA1210NHAUTO
V30MLA0603NHAUTO
V30MLA0805LNHAUTO
V30MLA1210NHAUTO
V30MLA1210LNHAUTO
V33MLA1206NHAUTO
V42MLA1206NHAUTO
V48MLA1210NHAUTO
V48MLA1210LNHAUTO
Specifications (25ºC)
Maximum
Maximum
Jump
Load
Non-repetitive Non-repetitive
Start
dump
Surge Current Surge Energy
Voltage
Energy
(8/20µs)
(10/1000µs)
(5 min)
VM(AC)
VJUMP
WLD
ITM
WTM
(V)
(V)
(V)
(J)
(A)
(J)
3.5
3.5
3.5
3.5
5.5
5.5
5.5
5.5
9.0
9.0
12.0
14.0
14.0
14.0
14.0
18.0
18.0
18.0
18.0
18.0
26.0
26.0
26.0
26.0
26.0
30.0
30.0
30.0
30.0
33.0
42.0
48.0
48.0
2.5
2.5
2.5
2.5
4.0
4.0
4.0
4.0
6.5
6.5
9.0
10.0
10.0
10.0
10.0
14.0
14.0
14.0
14.0
14.0
20.0
20.0
20.0
20.0
20.0
25.0
25.0
25.0
25.0
26.0
30.0
40.0
40.0
---------------24.5
24.5
24.5
24.5
24.5
27.5
27.5
27.5
27.5
27.5
29
29
29
29
36
48
48
--
---------------0.3
1
0.7
1.5
3
0.4
1
0.7
1.5
3
0.4
0.7
3
3
1.5
1.5
3
--
30
120
40
100
30
120
40
150
30
40
40
30
120
40
150
30
120
40
150
500
30
100
40
150
300
30
30
280
220
180
180
250
220
0.100
0.300
0.100
0.300
0.100
0.300
0.100
0.400
0.100
0.100
0.100
0.100
0.300
0.100
0.400
0.100
0.300
0.100
0.400
2.500
0.100
0.300
0.100
0.600
1.200
0.100
0.100
1.200
0.900
0.800
0.800
1.200
0.900
Maximum
Clamping
Voltage
at 1A (or
as Noted)
(8/20µs)
Nominal
Voltage at
1mA DC Test
Current
Typical
Capacitance
at f = 1MHz
(V)
VN(DC)
Min
(V)
VN(DC)
Max
(V)
(pF)
13.0
13.0
13.0
13.0
17.5
17.5
17.5
17.5
25.5
25.5
29.0
34.5
32.0
32.0
32.0
50.0
44.0
44.0
44.0
44.0 at 2.5
60.0
60.0
60.0
60.0
60.0 at 2.5
74.0
72.0
68.0 at 2.5
68.0 at 2.5
75.0
92.0
105.0 at 2.5
105.0 at 2.5
3.7
3.7
3.7
3.7
7.1
7.1
7.1
7.1
11.0
11.0
14.0
15.9
15.9
15.9
15.9
22.0
22.0
22.0
22.0
22.0
31.0
29.5
29.5
29.5
29.5
37.0
37.0
35.0
35.0
38.0
46.0
54.5
54.5
7.0
7.0
7.0
7.0
9.3
9.3
9.3
9.3
16.0
16.0
18.5
21.5
20.3
20.3
20.3
28.0
28.0
28.0
28.0
28.0
38.0
38.5
38.5
38.5
38.5
46.0
46.0
43.0
43.0
49.0
60.0
66.5
66.5
1270
176
1380
7500
960
1840
660
3500
490
520
410
180
560
320
1200
120
520
290
1270
2930
110
220
190
720
1480
90
130
900
600
500
425
400
380
VC
C
NOTES:
1. 'L' suffix is a low capacitance and energy version; Contact your Littelfuse sales representative for custom capacitance requirements
2.Typical leakage at 25ºC<25µA, maximum leakage 100µA at VM(DC)
3.Average power dissipation of transients for 0603, 0805, 1206 and 1210 sizes not to exceed 0.05W, 0.1W, 0.1W and 0.15W respectively
4. Load dump :min. time of energy input 40ms, interval 60sec(the load dump time constant Td differs from the time constant of energy input; load dump rating for ISO 7637-2 pulse 5a and
ISO16750-2 Table 5A.
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15
Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
Peak Current and Energy Derating Curve
Peak Pulse Current Test Waveform for Clamping Voltage
PERCENT OF RATED VALUE
100
PERCENT OF PEAK VALUE
When transients occur in rapid succession, the average
power dissipation is the energy (watt-seconds) per pulse
times the number of pulses per second. The power so
developed must be within the specifications shown
on the Device Ratings and Specifications Table for the
specific device. For applications exceeding 125°C ambient
temperature, the peak surge current and energy ratings
must be derated as shown below.
50
0
T
O1
Figure 2
100
TIME
T1
T2
80
60
40
20
0
-55
Figure 1
50
60
70
80
90
100
110
120
AMBIENT TEMPERATURE ( oC)
FIGURE 1. PEAK CURRENT AND ENERGY
DERATING CURVE
130 140 150
01 = Virtual Origin of Wave
T = Time from 10% to 90% of Peak
FIGURE
2. Time
PEAK =
PULSE
TEST WAVEFORM
T1 = Rise
1.25 xCURRENT
T
FOR CLAMPING VOLTAGE
T2 = Decay Time
Example - For an 8/20 µs Current Waveform:
O1 = VIRTUAL ORIGIN OF WAVE
8µsFROM
= T1 10%
= Rise
Time
t = TIME
TO 90%
OF PEAK
t1 = VIRTUAL
TIME = 1.25
xt
20µs =FRONT
T2 = Decay
Time
t2 = VIRTUAL TIME TO HALF VALUE
(IMPULSE DURATION)
EXAMPLE:
FOR AN 8/20 s CURRENT WAVEFORM
8 s = t1 = VIRTUAL FRONT TIME
20 s = t2 = VIRTUAL TIME TO
HALF VALUE
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15
Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
Limit V-I Characteristic for V3.5MLA0603NHAUTO to
V30MLA0603NHAUTO
Limit V-I Characteristic for V3.5MLA0805LNHAUTO to
V30MLA0805LNHAUTO
1000
1000
V30MLA0805LNHAUTO
V30MLA0603NHAUTO
V26MLA0805LNHAUTO
V26MLA0603NHAUTO
V18MLA0805LNHAUTO
V18MLA0603NHAUTO
100
Varistor Voltage (V)
Varistor Voltage (V)
V14MLA0603NHAUTO
V9MLA0603NHAUTO,
V9MLA0603LNHAUTO
V5.5MLA0603NHAUTO,
V5.5MLA0603LNHAUTO
V3.5MLA0603NHAUTO
10
100
V14MLA0805LNHAUTO
10
V12MLA0805LNHAUTO
V9MLA0805LNHAUTO
5MLA0805LNHAUTO
V3.5MLA0805LNHAUTO
1
10µA
100µA
1mA
Figure 3
10mA
Current (A)
100mA
1A
10A
1
10µA
100A
100µA
1mA
10mA
1A
10A
100A
Current (A)
Figure 4
FIGURE X. LIMIT V-I CHARACTERISTIC FOR V3.5MLA0603NHAUTO TO V30MLA0603NHAUTO
Limit V-I Characteristic
for V3.5MLA0805NHAUTO to
V26MLA0805NHAUTO
100mA
FIGURE
LIMIT V-I CHARACTERISTIC
FOR V3.5MLA0805LNHAUTO TO V30MLA0805LNHAUTO
Limit
V-IX.Characteristic
for V3.5MLA1206NHAUTO
to
V42MLA1206NHAUTO
1000
1000
V30MLA0805LNHAUTO
V26MLA0805LNHAUTO
100
10
V12MLA0805LNHAUTO
V9MLA0805LNHAUTO
5MLA0805LNHAUTO
Varistor Voltage (V)
Varistor Voltage (V)
V18MLA0805LNHAUTO
V14MLA0805LNHAUTO
100
V42MLA1206
V33MLA1206
V26MLA1206
V18MLA1206
V14MLA1206
V5.5MLA1206
V3.5MLA1206
10
V3.5MLA0805LNHAUTO
1
10µA
100µA
1mA
10mA
100mA
1A
10A
100A
Current (A)
Figure 5
1
10µA
FIGURE X. LIMIT V-I CHARACTERISTIC FOR V3.5MLA0805LNHAUTO TO V30MLA0805LNHAUTO
Limit V-I Characteristic for V18MLA1210NHAUTO to
V48MLA1210NHAUTO
Figure 7
100µA
1mA
10mA
100mA
Current (A)
1A
10A
100A
1000A
FIGURE 6. LIMIT V-1 CHARACTERISTIC FOR V3.5MLA1206 TO V68MLA1206
1000
MAXIMUM CLAMPING VOLTAGE
MAXIMUM LEAKAGE
Varistor Voltage (V)
100
V48MLA1210NHAUTO, V48MLA1210LNHAUTO
V30MLA1210NHAUTO, V30MLA1210LNHAUTO
V26MLA1210NHAUTO
10
V18MLA1210NHAUTO
1
10µA
Figure 6
100µA
1mA
10mA
100mA
1A
10A
100A
1000A
CURRENT (A)
FIGURE X. LIMIT V-I CHARACTERISTIC FOR V18MLA1210NHAUTO TO V120MLA1210NHAUTO
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15
Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
Clamping Voltage Over Temperature (VC at 10A)
Device Characteristics
At low current levels, the V-I curve of the multilayer
transient voltage suppressor approaches a linear (ohmic)
relationship and shows a temperature dependent effect.
At or below the maximum working voltage, the suppressor
is in a high resistance modex (approaching 106Ω at its
maximum rated working voltage). Leakage currents at
maximum rated voltage are below 100µA, typically 25µA.
CLAMPING VOLTAGE (V)
100
Typical Temperature Dependance of the Haracteristic
Curve in the Leakage Region
V26MLA1206
V5.5MLA1206
10
-60
VNOM VALUE AT 25 oC (%)
SUPPRESSOR VOLTAGE IN PERCENT OF
100%
-40
-20
0
Figure 9
20
40
60
80
TEMPERATURE ( oC)
100
120
140
FIGURE 12. CLAMPING VOLTAGE OVER TEMPERATURE
(VC AT 10A)
Energy Absorption/Peak Current Capability
25
10%
1E -9
o
50o 75o
1E -8
100o 125 oC
1E -7
1E -6
1E -5
1E -4
1E -3
1E -2
SUPPRESSOR CURRENT (ADC)
Figure 8
FIGURE 10. TYPICAL TEMPERATURE DEPENDANCE OF THE CHARACTERISTIC
CURVE IN THE LEAKAGE REGION
Speed of Response
The Multilayer Suppressor is a leadless device. Its response
time is not limited by the parasitic lead inductances found
in other surface mount packages. The response time of
the ZNO dielectric material is less than 1ns and the MLA
Automotive Series can clamp very fast dV/dT events such as
ESD. Additionally, in "real world" applications, the associated
circuit wiring is often the greatest factor effecting speed of
response. Therefore, transient suppressor placement within
a circuit can be considered important in certain instances.
Energy dissipated within the MLA Automotive Series is
calculated by multiplying the clamping voltage, transient
current and transient duration. An important advantage of
the multilayer is its interdigitated electrode construction
within the mass of dielectric material. This results in
excellent current distribution and the peak temperature per
energy absorbed is very low. The matrix of semiconducting
grains combine to absorb and distribute transient energy
(heat) (see Speed of Response). This dramatically reduces
peak temperature; thermal stresses and enhances device
reliability.
As a measure of the device capability in energy and peak
current handling, the V26MLA1206 part was tested with
multiple pulses at its peak current rating (150A, 8/20µs). At
the end of the test,10,000 pulses later, the device voltage
characteristics are still well within specification.
Repetitive Pulse Capability
Multilayer Internal Construction
100
METAL
ELECTRODES
PEAK CURRENT = 3A
8/20 s DURATION, 30s BETWEEN PULSES
V26MLA1206
VOLTAGE
FIRED CERAMIC
DIELECTRIC
METAL END
TERMINATION
DEPLETION
REGION
10
0
DEPLETION
Figure 11
REGION
Figure 10
GRAINS
FIGURE 11. MULTILAYER INTERNAL CONSTRUCTION
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15
2000
4000
6000
8000
NUMBER OF PULSES
FIGURE 13.
REPETITIVE PULSE CAPABILITY
10000
12000
Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
Lead (Pb) Soldering Recommendations
Wave soldering is the most strenuous of the processes.
To avoid the possibility of generating stresses due to
thermal shock, a preheat stage in the soldering process
is recommended, and the peak temperature of the solder
process should be rigidly controlled.
When using a reflow process, care should be taken
to ensure that the MLA Automotive Series chip is not
subjected to a thermal gradient steeper than 4 degrees
per second; the ideal gradient being 2 degrees per second.
During the soldering process, preheating to within 100
degrees of the solder's peak temperature is essential to
minimize thermal shock.
Once the soldering process has been completed, it is
still necessary to ensure that any further thermal shocks
are avoided. One possible cause of thermal shock is hot
printed circuit boards being removed from the solder
process and subjected to cleaning solvents at room
temperature. The boards must be allowed to cool gradually
to less than 50º C before cleaning.
250
250
TEMPERATURE
°C °C
TEMPERATURE
TEMPERATURE
°C
The recommended solder for the MLA Automotive Series
suppressor is a 62/36/2 (Sn/Pb/Ag), 60/40 (Sn/Pb) or 63/37
(Sn/Pb). Littelfuse also recommends an RMA solder flux.
Reflow Solder Profile
MAXIMUM TEMPERATURE
MAXIMUM230°C
TEMPERATURE
230°C
40-80
MAXIMUM TEMPERATURE
SECONDS
40-80
230°C
ABOVE 183°C
250
200
200
SECONDS
ABOVE 183°C
RAMP RATE40-80
SECONDS
<2°C/s RATE
RAMP
ABOVE 183°C
<2°C/s
PREHEAT DWELL
RAMP RATE
PREHEAT DWELL
<2°C/s
200
150
150
150
100
100
100
50
50
Figure
PREHEAT ZONE
PREHEAT
DWELL
PREHEAT
ZONE
50
0
00
0
120
0
0.5
0.5
Note: the Lead–free paste, flux and profile were used for
evaluation purposes by Littelfuse, based upon industry
standards and practices. There are multiple choices of all
three available, it is advised that the customer explores the
optimum combination for their process as processes vary
considerably from site to site.
3.0
3.0
TIME (MINUTES)
3.5
3.5
4.0
4.0
3.5
4.0
FIGURE 14. REFLOW SOLDER PROFILE
MAXIMUM WAVE 260°C
MAXIMUM WAVE 260°C
250
300
250
MAXIMUM WAVE 260°C
200
250
200
150
200
150
SECOND PREHEAT
SECOND PREHEAT
100
150
100
SECOND PREHEAT
FIRST PREHEAT
FIRST PREHEAT
50
100
50
0
500.0
0
130.0
Lead–free (Pb-free) Soldering Recommendations
FIRST PREHEAT
0.5
0.5
1.0
1.0
1.5
2.0
2.5
3.0
3.5
1.5 TIME
2.0(MINUTES)
2.5
3.0
3.5
TIME (MINUTES)
0.5
1.0 15.1.5
2.5 PROFILE
3.0
3.5
FIGURE
WAVE2.0SOLDER
TIME SOLDER
(MINUTES)PROFILE
FIGURE 15. WAVE
4.0
4.0
4.5
4.5
4.0
4.5
FIGURE 15. WAVE SOLDER PROFILE
Lead–free Re-flow Solder Profile
300
300
250
300
250
TEMPERATURE
°C °C
TEMPERATURE
TEMPERATURE
°C
The reflow profile must be constrained by the maximums
in the Lead–free Reflow Profile. For Lead–free wave
soldering, the Wave Solder Profile still applies.
1.5
2.0
2.5
1.5
2.0
2.5
TIME (MINUTES)
0.5
1.0
1.5
2.0
2.5PROFILE
3.0
FIGURE
14. REFLOW
SOLDER
TIME (MINUTES)
FIGURE 14. REFLOW
SOLDER PROFILE
0
0.0
The preferred solder is 96.5/3.0/0.5 (SnAgCu) with an RMA
flux, but there is a wide selection of pastes and fluxes
available with which the Nickel Barrier parts should be
compatible.
1.0
1.0
300
300
Figure
Littelfuse offers the Nickel Barrier Termination option (see
"N" suffix in Part Numbering System for ordering) for the
optimum Lead–free solder performance, consisting of a
Matte Tin outer surface plated on Nickel underlayer, plated
on Silver base metal.
PREHEAT ZONE
Wave Solder Profile
TEMPERATURE
°C °C
TEMPERATURE
TEMPERATURE
°C
The principal techniques used for the soldering of
components in surface mount technology are IR Re-flow
and Wave soldering. Typical profiles are shown on the right.
200
250
200
150
200
150
100
150
100
50
100
50
Figure
MAXIMUM TEMPERATURE 260˚C,
TIME WITHIN
5˚C OF PEAK 260˚C,
MAXIMUM
TEMPERATURE
20 SECONDS
MAXIMUM
TIME
WITHIN 5˚C
OF PEAK
20
SECONDS
MAXIMUM
MAXIMUM TEMPERATURE
260˚C,
RAMP RATE
TIME WITHIN 5˚C OF
PEAK
<3˚C/s
RAMP
RATE
20 SECONDS MAXIMUM
<3˚C/s
RAMP RATE
<3˚C/s
60 - 150 SEC
217˚C
60 >
- 150
SEC
> 217˚C
60 - 150 SEC
> 217˚C
PREHEAT ZONE
PREHEAT ZONE
PREHEAT ZONE
0
50 0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
0
0
1.0
2.0 TIME
3.0(MINUTES)
4.0
5.0
6.0
7.0
0
TIME (MINUTES)
0 FIGURE
1.0 16. LEAD-FREE
2.0
3.0 RE-FLOW
4.0
5.0
6.0
7.0
SOLDER
PROFILE
RE-FLOW SOLDER PROFILE
14 FIGURE 16. LEAD-FREE
TIME (MINUTES)
FIGURE 16. LEAD-FREE RE-FLOW SOLDER PROFILE
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15
Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
Product Dimensions (mm)
PAD LAYOUT DIMENSIONS
CHIP LAYOUT DIMENSIONS
C
E
B
NOTE
D
L
W
A
NOTE : Avoid metal runs in this area, parts not recommended for use in applications using
Silver (Ag) epoxy
paste. Avoid metal runs in this area.
NOTE:
Parts not recommended for use in
1210
Size
1206 paste.
Size
applications
using silver epoxy
Dimension
IN
MM
IN
MM
0805 Size
0603 Size
IN
MM
IN
MM
A
0.160
4.06
0.160
4.06
0.120
3.05
0.100
2.54
B
0.100
2.54
0.065
1.65
0.050
1.27
0.030
0.76
C
0.040
1.02
0.040
1.02
0.040
1.02
0.035
0.89
D (max.)
0.113
2.87
0.071
1.80
0.043
1.10
0.040
1.00
E
0.020
-/+0.010
0.50
-/+0.25
0.020
-/+0.010
0.50
-/+0.25
0.020 -/+
0.010
0.50 -/+
0.25
0.015
-/+0.008
0.4
-/+0.20
L
0.125
-/+0.012
3.20
-/+0.30
0.125
-/+0.012
3.20
-/+0.30
0.079
-/+0.008
2.01
-/+0.20
0.063
-/+0.006
1.6
-/+0.15
W
0.100
-/+0.012
2.54
-/+0.30
0.060
-/+0.011
1.60
-/+0.28
0.049
-/+0.008
1.25
-/+0.20
0.032
-/+0.060
0.8
-/+0.15
Part Numbering System
V 18 MLA 1206 X X X AUTO
AUTOMOTIVE SERIES
DEVICE FAMILY
Littelfuse TVSS Device
PACKING OPTIONS (see Packaging table for quantities)
H: 7in (178mm) Diameter Reel, Plastic Carrier Tape
MAXIMUM DC
WORKING VOLTAGE
MULTILAYER SERIES
DESIGNATOR
DEVICE SIZE:
0603 = .063 inch x .031 inch (1.6 mm x 0.8 mm)
0805 = .08 inch x .08 inch (2.0 mm x 1.25 mm)
1206 = .126 inch x .063 inch (3.2 mm x 1.6 mm)
1210 = .126 inch x .1 inch (3.2 mm x 2.5 mm)
END TERMINATION INDICATOR
N: Nickel Barrier
(Matte Tin outer surface, plated on Nickel underlayer
plated on silver base metal)
CAPACITANCE OPTION
No Letter: Standard
L: Low Capacitance Version
Packaging*
Quantity
Device Size
7” Inch Reel
("H" Option)
1210
1206
0805
0603
2,000
2,500
2,500
2,500
*(Packaging) It is recommended that parts be kept in the sealed bag provided and that parts be used as soon as possible when removed from bags.
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15
Metal-Oxide Varistors (MOVs)
Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series
Tape and Reel Specifications
D0
PRODUCT
IDENTIFYING
LABEL
P0
For T and H Pack Options: PLASTIC CARRIER TAPE
For R Pack Options: EMBOSSED PAPER CARRIER TAPE
P2
E
F
K0
W
B0
t1
D1
P1
Symbol
A0
Description
EMBOSSMENT
TOP TAPE
8mm
NOMINAL
178mm
OR 330mm
DIA. REEL
Dimensions in Millimeters
0603, 0805, 1206 & 1210 Sizes
A0
Width of Cavity
Dependent on Chip Size to Minimize Rotation.
B0
Length of Cavity
Dependent on Chip Size to Minimize Rotation.
K0
Depth of Cavity
Dependent on Chip Size to Minimize Rotation.
W
Width of Tape
8 -/+0.3
F
Distance Between Drive Hole Centers and Cavity Centers
3.5 -/+0.05
E
Distance Between Drive Hole Centers and Tape Edge
1.75 -/+0.1
P1
Distance Between Cavity Centers
4 -/+0.1
P2
Axial Drive Distance Between Drive Hole Centers & Cavity Centers
2 -/+0.1
P0
Axial Drive Distance Between Drive Hole Centers
D0
Drive Hole Diameter
1.55 -/+0.05
4 -/+0.1
D1
Diameter of Cavity Piercing
1.05 -/+0.05
T1
Top Tape Thickness
0.1 Max
NOTES:
• Conforms to EIA-481-1, Revision A
• Can be supplied to IEC publication 286-3
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/09/15