Surge Protection Module LED Lighting Surge Protection Module > LSP05 LSP05 Module Series RoHS Description The Littelfuse LSP05 thermally protected Surge Protective Device is a self-protected device which is specially designed to be used in outdoor and commercial LED lighting fixtures for transient overvoltage protection. It is constructed with Littelfuse thermally protected varistor technology. Its built-in thermal disconnect function provides additional protection to prevent catastrophic failure and fire hazard even under the extreme circumstances of varistor end-of-life or sustaining over voltage conditions. The LSP05 SPD facilitates customer’s product compliance to IEEE C62.41.2 Location Category C Low and US Dept of Energy MSSLC Model Spec. Agency Approvals Agency Features Standard Agency File Number UL1449 E320116 Applications • Outdoor and Commercial LED Lighting • Roadway lighting • Traffic lighting • Digital signage • • • • • Wash wall lighting Parking garage/lot lighting Flood lighting Tunnel lighting Street lighting Additional Information • Maximum Discharge Current, 10kA, 8/20us • Meets ANSI C136.2 Enhanced Level 10kV/5kA and IEEE C62.41.2 Location Category C Low Exposure • Parallel connected SPD device • Thermally protected Varistor technology • IP66 Water-proof and Dust-proof • Indication wire lead options for Parallel connected modules • UL1449 Type 4 Component Assembly Recognition • IEC61643-11 Class II/ EN61643-11 Type 2 Compliant1 • Compact form factor (48x48x30mm) with mounting tabs • 240Vac and 277Vac voltage ratings are CE compliant and available for Class I and Class II installation based on IEC luminaire protection classes Notes: 1. Self-declared compliance. Datasheet Resources Samples Absolute Maximum Ratings • For ratings of individual members of a series, see Device Ratings and Specifications chart LSP05 Series Units 150 to 510 V Continous: Steady State Applied Voltage: Max AC Voltage Range (VM(AC)RMS) Transient: Maximum Discharge Current 8/20μs Waveform (Imax) 10,000 A Nominal Discharge Current 8/20µs Waveform (In) 5,000 A Operating Ambient Temperature Range (TA) -45 to +85 °C Storage Temperature Range (TSTG) -45 to +125 °C Isolation Voltage Capability (When the thermal disconnect opens) Insulation Resistance 600 V >1,000 MΩ CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. 2 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/06/15 Surge Protection Module LED Lighting Surge Protection Module > LSP05 LSP05 Series Device Ratings & Specifications MCOV/Uc (VAC)5 Maximum Discharge Current (Imax)(A)2 LSP05120* 120 150 10,000 LSP05240* 240 275 10,000 LSP05277* 277 320 10,000 LSP05347* 347 420 10,000 LSP05480* 480 510 10,000 L-L:240 L-L:275 LSP05240LL* LSP05480LL* L-N/G:120 L-N/G:150 L-L:480 L-L:510 L-N/G:277 L-N/G:320 Nominal Discharge Current (In)(A)1 MLV (V)3 Up (V)4 L-N:680 L-G:680 800 N-G:630 L-N:1100 5,000 L-G:1100 1200 N-G:1100 L-N:1270 5,000 L-G:1270 1400 N-G:1220 Typical Dimensions (mm) L-N:1600 5,000 L-G:160056.0 ±0.51700 N-G:1580 L-N:1780 5,000 L-G:1780 1900 N-G:1730 Safety Compliance IEC/EN 61643-116 UL1449 5,000 10,000 5,000 10,000 5,000 L-L:1100 X X X X X X X L-L:1200 L-N/G:680 L-N/G:800 L-L:1780 L-L:1900 L-N/G:1270 L-N/G:1400 X 48.0±1.5 2x ø4.8±0.2 X X X LV UltraMOV™ Series Operating Voltage (VAC) Part Number7 Notes: 1. Nominal Discharge Current (In)(A): The nominal discharge current is a measure of the SPDs endurance capability; 15 impulses of discharge current uses the 8/20us current waveform. 2. Maximum Discharge Current (Imax)(A): The maximum discharge current is a measure of the100 SPDs maximum capability; current uses3 the 8/20us current indication wires ±20 100 ±20 48.0single ±1.5 impulse of discharge all use the AWG22. waveform. 3. MLV – UL1449 Measured limiting voltage; the highest value of residual voltage measurements during the application of impulses of 8/20us nominal discharge current (In); an average voltage value of 15 impulses 4. Up – IEC 61643-11 Voltage protection level; the highest value of residual voltage measurements during the application of impulses of 8/20us nominal discharge current (In); a rounding voltage value of maximum measurement. 30.0 ±1.0 2.3 ±0.2 5. MCOV/UC: Maximum Continuous Operating Voltage - maximum r.m.s. voltage that could be continuously applied to the SPD. 6. Part Numbers LSP05xxxPM Only. 7. * = - P or PM 6 ±2 64.0 ±1.5 6 ±2 Dimensions Typical Dimensions (mm) 56.0 ±0.5 48.0±1.5 2x ø4.8±0.2 100 ±20 48.0 ±1.5 100 ±20 30.0 ±1.0 2.3 ±0.2 6 ±2 3 indication wires all use the AWG22. 64.0 ±1.5 6 ±2 LSP05XXXXXP LSP05XXXXXPM Notes: 1. Black: Line; White: Neutral; Green: Ground (P/N with suffix X3333/X3316: Brown: Line; Blue: Neutral; Green-Yellow stripe: Ground) 2. Black: R1; Red: R2; Blue: R3 3. Wire Gauge: AWG14 wire Line in, AWG22 Wire for indication; Wire Length: 100mm or customized © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/06/15 3 Surge Protection Module LED Lighting Surge Protection Module > LSP05 Part Numbering System Application/Installation Schematic L L or N/G L L N N AC/DC Power Supply G Parallel Connection With LED indicating SPD status - ON (green): SPD is online - OFF: SPD needs replacement - LED Module R1 R2 R3 SPD LSP 05 480LL P Xxxxx + NC LED normally on LSP05xxxPM Device Family Littelfuse Surge Protection Module Nominal Discharge Current (In) Operating Voltage Connection mode LL: for L,L,N/G Blank: L-N, L-G, N-G R P or PM L L or N/G L L N N AC/DC Power Supply G (P: parallel connection; PM: parallel connection and with monitor indication wire) + - LED Module R1 Parallel Connection SPD LED normally off R2 R3 With LED indicating SPD status LSP05xxxPM - OFF: SPD is online - ON (red): SPD needs replacement Other non-standard option: X3333: with GND wire connection, available for 240Vac and 277Vac rating with CE Marking for Class I earthed installation X3316: without GND wire connection option R Notes: 1. LED indicator and associated circuitry are not included in the module. 2. R1 must be capped off by wire nut when not connected (NC). 3. R1 and R2 are AC line voltage (hot); R3 is AC neutral voltage. 4. R2 voltage is cut off when SPD needs replacement. 5. R is current limiting resistor; it resistance/wattage is determined by AC line voltage and desired current driving LED. Example: AC line voltage 240V, LED: 1.6mA, resistor: 150Kohm/0.5W. L L N/G or L L N N AC/DC Power - LED Module G Parallel Connection SPD L L N N Parallel Connection (for Class II Unearthed) AC/DC Power Supply G 4 + Supply + - LED Module SPD ~X3316 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/06/15